Pyle view PLVSHR77 Manual de usuario
7" WIDE SCREEN 16:9 TFT-LCD MONITOR
PLVSHR77
1
1. Table of Contents------------------------------------- 1
2. Warning ----------------------------------------------- 1
3. Installation -------------------------------------------- 2
5. Installation for Monitor ------------------------------ 5
6. Accessories ------------------------------------------- 7
7. Specifications ---------------------------------------- 7
4. Features ----------------------------------------------- 3
4.1 Features ------------------------------------------- 3
4.2 Remote Control Bar ------------------------------ 3
4.3 Function keys at front panel --------------------- 4
3. INSTALLATION
1. Rotate the locking knob on the neck of the
mounting stand clockwise.
2. Slide the engagement head on the mounting
stand into the slide bracket slot on the rear of
the monitor housing.
3. Rotate the locking knob counterclockwise
until it is hand-tight and the monitor is securely
fastened to the neck of the mounting stand.
4. Locate a desirable spot in your vehicle for the
monitor. Hold it place there, with the mounting
plate resting in approximately the right location
and have a friend sit in the seat from which you
intend viewing of this monitor to take place to
confirm the location of the monitor. If necessary,
loosen the angle adjustment knob and rotate the
monitor to a more ideal angle and retighten.,
5. Once you have confirmed the location of the
monitor, remove the adhesive backing from
the underside of the mounting plate and firmly
press all the "petals" of the mounting plate
down to the car surface. Temporarily remove
the monitor by loosening the locking knob, and
use three screws in the locations indicated in
the drawing below to further secure the monitor
mounting plate. If necessary, drill pilot holes to
assist in inserting the screws.
6. Reinstall the monitor onto the neck of the mounting
stand and tighten the locking knob. Adjust the monitor
angle again as required, being sure to tighten the angle
adjustment knob when you are done.
2
3
4. Function:
4.1 Features
4.2 Remote Control Bar
1. Headphone Jack
2. Power
3. UP key
5. Down key
6. Menu
7. AV-IN Jack
8. Interface cable
9. System Cable
10. Audio in (Red RCA Jack)
11. Video in ( Yellow RCA Jack)
12. Power Wire (Red)
13. Grounding Wire (Black)
8
9
10 RED
11 YELLOW
12 RED 13 BLACK
4. IR Sensor
1234
5678
90
POWER
MUTE
TV/AV
TV/CATV
SETUP
FM/AM
Monitor
FUNC
UP
+
MODE
DN
-
CHVOL
POWER
MUTE
FUNC
UP
DOWN
To adjustfunctions of Monitor, use only 5keys:
Power: Press the Power button for ON/OFF
Mute: To shutdownAudio output
Function: Press the Function button to accessOn Screen
Display Menu of:CONTRAST / BRIGHTNESS /
COLOR / SHARPNESS / SOURCEIN /
VOLUME / MODE /LEFT RIGHT
/ RECALL / EXIT
UP+: To Adjust Volume Up
DN-: To Adjust Volume Down
MODE: Selection button forAV1 / AV2
MODE
4
4.3 FUNCTION KEYS AT FRONT PANEL
1. MENU FUNCTIONS
1. POWER
Press the POWER button once it will be power ON. Press it
again. The will be power OFF.
2. UP / DOWN
Press "UP+" or "DN--"directly is to adjust volume. Using MENU
button together can adjust the other functions.
CONTRAST: Press or to adjust Contrast.
BRIGHTNESS: Press or to adjust Brightness.
COLOR: Press or to adjust Color.
SHARPNESS:
VOLUME: Press or to adjust Volume.
MODE: 16:9 / 4:3
LEFT / RIGHT: Left/Right Revolving
RECALL: The Display will Return to The
Original by Factory.
EXIT: Exit Menu Mode.
Press or to adjust Sharpness.
SOURCE IN: Selection button AV1 / AV2for
5
5. Installation for Monitor
Note
It is recommended that the fitting is carried
out at a specialist workshop.
6
8
Release Key
7
6. ACCESSORIES
(1) Monitor Stand x 1
(2) System Cable x 1
(3) Operation Manual x1
(4) Release Key x1
(5) Remote Controller x 1
(6) Warranty Card x 1
The specifications are subject to change without prior notice.
7. Specifications
1. Supply voltage 12Vdc 10%
5. Monitor screen size 7" ( 16: 9)
6. Operating system TFT active matrix.
7. Resolution 1440 x 234 dots.
11. Viewing angle (L/R; T/D): L/R:45/45 :Top/down :30/60 degrees
10. System NTSC / PAL Dual System View Area
2. Power consumption:
3. Operating temperature: 0 C ~+ 60 C
4. Storage temperature: -25 C ~ +70 C
9. Monitor weight: 450 20 g
12. Video input range: 0.5~1.25Vp-p/75 Ohms composite signal.
8. Monitor overall dimension: 190(W) x 126.8(H) x 36(D) mm.
14. Audio output power: 0.5W(Max.)
1A 10%
13. Audio input range: 0~1.5Vp-p/620 Ohms 50Hz ~ 20K Hz.
Tabla de contenidos
Otros manuales de Monitor de Pyle view
Pyle view
Pyle view PLVHR75 Manual de usuario
Pyle view
Pyle view PLVW1350IR Manual de usuario
Pyle view
Pyle view PLMRVW155 Manual de usuario
Pyle view
Pyle view PLVWR740 Manual de usuario
Pyle view
Pyle view PLVW1782R Manual de usuario
Pyle view
Pyle view PYLE PLHR58 Manual de usuario
Pyle view
Pyle view PLD7HB Manual de usuario
Pyle view
Pyle view PLYWR2200 Manual de usuario
Pyle view
Pyle view PLHR70 Manual de usuario
Pyle view
Pyle view PLVW1550IR Manual de usuario
Pyle view
Pyle view PLVHR75 Manual de usuario
Pyle view
Pyle view PLVWR1542 Manual de usuario
Pyle view
Pyle view PLHR58 Manual de usuario
Pyle view
Pyle view PLVHR72 Manual de usuario
Pyle view
Pyle view PLVWR1442 Manual de usuario
Pyle view
Pyle view PLVG7IR Manual de usuario
Pyle view
Pyle view PLHR7SP Manual de usuario
Pyle view
Pyle view PLVW1692R Manual de usuario
Pyle view
Pyle view PLVW1770IR Manual de usuario
Pyle view
Pyle view PLVWR910 Manual de usuario
