PVI Industries PV 19A Guía del usuario

PV 19A 7/12

START-UP OF STEAM AND BOILER WATER HEATERS

**FOR DETAILED INFORMATION SEE INSTALLATION & MAINTENANCE MANUAL **

WARNING: These startup instructions are prepared for a qualified service installer, service

agency or gas supplier and require and rely on the experience and training of these

qualified gas appliance technicians to be safely completed. Attempting to follow these

instructions without such training and experience can result in property damage, exposure

to hazardous materials, personal injury or death.

1. When placing a unit into operation, open relief valve to purge air from top of tank and begin to fill the tank with

cold water. Check for plumbing leaks. Be sure the tank is completely filled before closing the relief valve.

2. Push control switch, located on the control box, to “ON” to activate the control valves (steam or boiler water) and

thermostats. Check the valves for proper operation.

3. Check operating thermostat settings. The operating thermostat is set at the factory at approximately 120°F and the

upper operating thermostat (if supplied) is set at approximately 125°F. Adjustment may be made by turning the

thermostat’s dial to the desired temperature. The temperature limiting device is factory set at 200°F.

4. Push the operating switch to “OFF” before opening manual main steam or boiler water supply valve. The heating

supply should be introduced gradually until all passages of the heat exchanger are filled

5. Start operation gradually. Do not admit steam or boiler water to the unit suddenly when empty or cold. Do not

shock unit with cold fluid when unit is hot. . Slowly bring the unit up to temperature.

6. Do not operate unit under conditions in excess of those specified on nameplate.

7. Open nearby hot water tap to maintain a flow of water through the tank when starting up units. Regulate flow of

water through the tank to allow the control valve to cycle off and on, and check operation of all safety and

operating controls.

8. In all installations there should be no pulsation or water hammer since this causes vibration and strain with

resulting leaks.

9. Retighten bolting on all gasketed joints after the heat exchanger has reached temperature to prevent leaks and

gasket failures. Retightening should be done uniformly and in a diametrically staggered pattern

10. Complete the attached startup report.

Important – Contact PVI Customer Service, 800-433-5654, if any recommended setpoint or analysis

reading falls outside of the recommended ranges before completing startup.

PV 19 7/12 817-335-9531 ●800-433-5654 ●FAX 800-880-2019 ●www.pvi.com

START-UP REPORT

STEAM/WATER - TO - WATER HEATERS

QUICKDRAW®– CSX – ISX – HOT WATER GENERATOR

Warning: Startup must be performed by a qualified service installer, service agency or the gas supplier.

Model Number: Serial Number:

Job Name:

Address:

GENERAL INFORMATION

Restart? Yes No Installation is: New Replacement/Renovation Indoor Outdoor

Primary operating voltage: VAC Voltage from neutral to earth ground: (should be zero)

Thermostat Set Points: Hi-Limit °F Upper Operating: °F Operating °F

Operating (optional): °F Operating (optional): °F

Cold Water Inlet Temperature: °F Hot Water Outlet Temperature: °F

T & P Relief Valve(s) plumbed to a suitable drain? Yes No

WATER HEATER INSTALLATION

Type of piping connected to heater: Copper Brass Galvanized

Is there a check valve in the supply water piping? Yes No

Is there a water softener on the cold water supply? Yes No Operational? Yes No

Is there a mixing valve on the hot water supply? If yes; temperature setting: °F No

Is there expansion relief in the cold water supply? If yes, what type: tank valve No

Is there a recirculation loop? Yes Circulating pump horsepower: No

Is there a floor drain in the room? Yes No

STEAM SYSTEM

Static Steam Pressure: PSI Flow Steam Pressure: PSI Operating Steam Pressure: PSI

Is steam supplied from utility company or installed boilers

Is there a condensate trap in the steam supply main? Yes No

Is there lift in the condensate return line? (Before receiver tank) Yes No Lift in feet: FT

Is there a steam strainer ahead of the appliance steam valve? Yes No Size: in. Mesh:

Is there a steam trap ahead of the appliance steam valve? Yes No

Is there a steam trap in the appliance condensate line? Yes No

Does steam flow stop completely when steam valve is de-energized? Yes No

Page 1 of 2

PV 19 7/12 817-335-9531 ●800-433-5654 ●FAX 800-880-2019 ●www.pvi.com

Model Number: Serial Number:

HEATING WATER SUPPLY

Is heating water supplied from boiler? Yes No

If No, describe:

Heating water pump flow rate: GPM Pump Horsepower: HP

Supply water temperature: °F Return Water temperature: °F

Comments:

Service Company Name: Phone:

Service Company Address:

Start-up Performed By: Date:

Customer Representative: Date:

Important: You must submit the original copy of the completed form to your PVI representative before the

warranty will become effective on this product. Contact Customer Service for assistance at 1-800-433-5654.

Page 2 of 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de agua de PVI Industries

PVI Industries

PVI Industries CONQUEST 20 L 100 A-GCL Manual de instrucciones

PVI Industries

PVI Industries PV 6113b Manual de usuario

PVI Industries

PVI Industries TURBOPOWER 1000 N 225A-TPO Manual de usuario

PVI Industries

PVI Industries MAXIM 20 N 119A-MXS Manual de usuario

PVI Industries

PVI Industries 1000P1250A-TPGO Manual de usuario

PVI Industries

PVI Industries CONQUEST 20 L 100 A-GCL Manual de instrucciones

PVI Industries

PVI Industries PLATINUM 199 SS A-PN Manual de usuario

PVI Industries

PVI Industries 1000P600A-TPGO Manual de usuario

PVI Industries

PVI Industries 1000P900A-TPGO Manual de usuario

PVI Industries

PVI Industries COBREX Manual de instrucciones

PVI Industries

PVI Industries 150LX-250 A-PVIF Manual de instrucciones

PVI Industries

PVI Industries TURBOPOWER 1000 P 175A-TPL Manual de usuario

PVI Industries

PVI Industries MAXIM Manual de usuario

PVI Industries

PVI Industries 1000N600A-TPO Manual de usuario

PVI Industries

PVI Industries MAXIM 20 P 125A-MXS Manual de usuario

PVI Industries

PVI Industries TURBOPOWER 99 Manual de usuario

PVI Industries

PVI Industries 250P225A-TPL Manual de usuario

PVI Industries

PVI Industries 45N300A-E Manual de usuario

PVI Industries

PVI Industries 1000PHE125A-TPGO Manual de usuario

PVI Industries

PVI Industries QuickDraw Manual de instrucciones

PVI Industries

PVI Industries 1000N400A-TPO Manual de usuario

PVI Industries

PVI Industries 50 L 130 A-GCML Manual de instrucciones

PVI Industries

PVI Industries MAXIM 40 P 90A-MXG Manual de usuario

PVI Industries

PVI Industries TURBOPOWER 1000 P 250A-TPL Manual de usuario

Manuales populares de Calentador de agua de otras marcas

Kenmore

Kenmore 153.582400 Manual de usuario

Applimo

Applimo Edel AIR Manual de usuario

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manual de usuario

clage

clage E-Mini Series Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-180 Manual de usuario

Bradford White

Bradford White EF Series Manual de usuario

Eccotemp

Eccotemp 40-H Manual de usuario

Dimplex

Dimplex ECSd125-580 Guía

Dux

Dux 32FCR6N Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guía de solución de problemas

Noritz

Noritz N-132M Manual de instrucciones

TESY

TESY GCV7/4S 10047 Hoja de especificaciones

A.O. Smith

A.O. Smith Gphe 50 Manual de usuario

Koryo

Koryo KWHZF15Y Manual de usuario

Pentair

Pentair PSC-14-4-02 Manual de usuario

GE 40M06AAG Instrucciones de montaje

Thermor

Thermor AEROMAX SPLIT 2 Manual de usuario

American Hometec

American Hometec AHQ-B03X Manual de usuario