Purkeys DIRECT PLUS Guía de configuración
A MISSION CRITICAL ELECTRONICS BRAN
D
DIRECT™PLUS
DIAGNOSTIC GUIDE
300-48 R1.01
1
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
CONTENTS
Cover Assembly..................................................................................................2
Interior Light Module (optional) .....................................................................2
Connections Inside Nosebox............................................................................3
Connections Outside Nosebox.........................................................................3
Wire Diagram .....................................................................................................4
Basic Troubleshooting .......................................................................................4
No Lights on Face of the Nosebox..........................................................4
Batteries Not Being Charged ...................................................................6
Interior Lights Not Working (if installed)...........................................11
Limited Commercial Warranty Policy...........................................................13
2
COVER ASSEMBLY
INTERIOR LIGHT MODULE (OPTIONAL)
3
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
DIRECT PLUS DIAGNOSTIC GUIDE
CONNECTIONS INSIDE NOSEBOX
CONNECTIONS OUTSIDE NOSEBOX
4
Step 1: Make sure that connections
are tight and inspect wiring for
defects.
BASIC TROUBLESHOOTING
Step 2: Check the 2 amp fuse in
the battery box at the DC/DC
converter.
• If blown , replace
• If good, proceed
WIRE DIAGRAM
NO LIGHTS ON FACE OF THE NOSEBOX
5
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
DIRECT PLUS DIAGNOSTIC GUIDE
Step 3: Using a voltmeter, measure
the voltage at the 2-pin terminal
strip on the DC/DC converter
charging plate:
• Place the positive lead on the
ligate batt+ stud.
• Place the negative lead on the
ground stud.
• If there is a battery voltage
reading, skip to step 5.
• If no voltage is shown, proceed
to step 4.
Step 4: Check the 30 amp circuit
breaker using a voltmeter:
• Place the positive lead on
the circuit breaker stud that
connects to the red junction
stud closest to the DC/DC
converter on the plate.
• Place the negative lead on the
negative post of the battery.
• If there is a battery voltage
reading, proceed to the next
step.
• If no voltage is shown, reset the
circuit breaker.
• If there is still no voltage, check
wiring for defects.
• If no defects are found, replace
the circuit breaker
6
BATTERIES NOT BEING CHARGED
Step 1: Connect the tractor 7-way
cable to the trailer and start the
tractor.
• Place the voltmeter positive
lead on the stud labeled
positive input.
• Place the negative lead on the
negative battery post.
• If there is a voltage reading,
proceed to the next step.
• If there is no voltage reading,
skip to step 8.
Step 5: On the front of the trailer,
remove the hardware holding the
cover assembly to the nosebox
base.
• Place the voltmeter positive
lead where the orange wire is
connected.
• Place the negative lead where
the white wire is connected.
• Check the battery voltage
reading.
• If there is a battery voltage
reading, replace the cover
assembly on the base.
• If there is no voltage reading,
inspect the wiring for defects
and repair any issues.
7
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
DIRECT PLUS DIAGNOSTIC GUIDE
Step 2: Next:
• Place the voltmeter positive
lead on the yellow wire stud
labeled ignition.
• Place the negative lead on the
negative battery post.
• Battery voltage should read
approximately 10-13 volts.
Step 3: Unplug the 4-pin connector
from the DC/DC converter.
• Place the voltmeter positive
lead in pin #1 (12v + input).
• Place the negative lead in pin
#3 (ground).
Readings should be approximately
the tractor voltage:
• If yes, go to the next step.
• If no, inspect the wiring and
plug.
Step 4: Next:
• Place the voltmeter negative
lead in pin #3 (ground).
• Place the positive lead in pin #4
(ignition).
Reading should be approximately
10-13 volts.
• If yes, go to the next step.
• If no, inspect the wiring and
plug.
8
Step 5: Next:
• Place the voltmeter negative
lead on the negative battery
post.
• Place the positive lead on the
red junction stud closest to the
converter.
Reading should be 13+ volts.
• If yes, proceed to the next step.
• If no, replace the wiring from
the converter to the converter
plug.
Step 6: Next:
• Place the voltmeter negative
lead on the negative battery
post.
• Place the positive lead on the
circuit breaker post away from
the battery.
Reading should be 13+ volts.
• If yes, proceed to the next step.
• If no, inspect the wiring
between the junction stud and
the circuit breaker and repair
any issues.
Otros manuales para DIRECT PLUS
1
Tabla de contenidos
Otros manuales de Cargador de baterías de Purkeys
Purkeys
Purkeys SOLAR BOLT Manual de usuario
Purkeys
Purkeys Select P1020-K Manual de usuario
Purkeys
Purkeys BOSS-01 Manual de usuario
Purkeys
Purkeys Liftgate Double Check Manual de usuario
Purkeys
Purkeys DIRECT FLEX Guía de configuración
Purkeys
Purkeys DIRECT Guía de configuración
Purkeys
Purkeys SELECT Guía de configuración
Purkeys
Purkeys SOLAR BOLT Manual de usuario
Purkeys
Purkeys DIRECT PLUS Manual de usuario
Purkeys
Purkeys DIRECT-03 Manual de usuario
