Puretec Sparq S4 Manual de usuario
Sparq S4 User Guide
Sparkling, Chilled & Still Water System
For correct operation & installation it is essential to observe these instructions.
APR2018
SODA
COLD
CHILLING
WMTS 105
Certicate No. 23291
Australian Certication
Services
2
Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
AUSTRALIA
Customer Service: 1300 140 140
Email: [email protected]
Web: www.puretec.com.au
NEW ZEALAND
Customer Service: 0800 130 140
Email: [email protected]
Web: www.puretec.co.nz
What's Inside
What's Inside
Puretec Customer Service ...........................................................................................................................3
Installation Record ...........................................................................................................................................3
SPARQ-S4 .............................................................................................................................................................3
Before Installation.............................................................................................................................................4
Parts Included......................................................................................................................................................4
Specications.......................................................................................................................................................5
Dimensions............................................................................................................................................................5
Tap Button Identication ...............................................................................................................................6
Installation Procedure ....................................................................................................................................8
How To Use Quick Connect Fittings......................................................................................................10
How to operate the tap:..............................................................................................................................12
Filter Maintenance - Every 12 Months or when taste returns ..............................................12
Gas Replacement - As Required.............................................................................................................13
Troubleshooting...............................................................................................................................................14
Warranty..............................................................................................................................................................15
3
Copyright © Puretec Pty Ltd 2018 Puretec Sparq S4 User Guide
Introduction
Puretec Customer Service
Thank you for purchasing a Puretec Sparq S4 Drinking Water Appliance. The Sparq S4 is
a proven performer manufactured from only quality materials and components. It will
give years of reliability and trouble free operation if maintained properly.
Caution: Do not use with water that is microbiologically unsafe or without adequate
disinfection before or aer the system.
The Puretec Sparq S4 is designed for metropolitan supply water only.
Puretec Drinking Water Appliances are designed to run economically for many years and
this is dependant on the initial installation and periodic maintenance.
Flush system for 5 minutes or more, aer any period of non-use, more than 2 weeks.
Note: Where maximum line pressure exceeds 500 kPa, the supplied multivalve must
be installed to comply with Australian Plumbing Standards.
PRODUCT INFORMATION
Model Number SPARQ-S4
Serial / Batch Number
(Refer to label on the rear of the unit)
Purchased from:
Date of Installation
Installer / Plumber Details
Installation Record
For future reference, ll in the following data
All installation and service work should be completed by qualied tradespeople. Faulty
operation due to unqualied persons will result in voided warranty.
All plumbing must comply with AS 3500.1 and AS3500.2.15
4
Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
Before Installation
Read the instructions and check if there is adequate space to mount all of the
components. Measurements min. required.
Check the mains water pressure is between 172 - 500kPa
NOTE: This product must be connected to MAINS WATER ONLY
Check the appliance rating plate and ensure correct power is available for the appliance.
Check the under counter cupboard supporting the appliance is adequate for the total net
weight of 24kg (including the gas bottle).
Ensure there is adequate ventilation available through the cupboard. If there is
inadequate ventilation, and the cupboard temperature rises to above 40°C, the system
may become damaged and malfunction which will void the product warranty. To ensure
there is sucient cross-ow ventilation suitable holes or vents will need to be cut into
the cupboard and door.
Parts Included
Pre-installation
Sparq Unit Faucet/Tap
Wiring loom
SmartTeeTM
CO2Bottle
TubingMultivalve
Regulator
SODA
COLD
CHILLING
Power CordStraight
Connector
Spacer
5
Copyright © Puretec Pty Ltd 2018 Puretec Sparq S4 User Guide
Specications
Specications
A Ø26mm hole required for faucet (Max. 30mm)
^Warranty cover parts and labour for the period of 1 year where applicable subject to approval.
Dimensions
Model: SPARQ-S4
Throughput L/hour: 20
Chilled temperature: 4°C to 10°C
Power requirements: 50Hz / 220~240 V
Max power consumption: 100 W
Tap Dimensions 423 (H) x 205 mm (W)
Appliance Dimensions 230 (W) x 370 (D) x 390 mm (H)
Warranty: 1 year^
205mm
minimum
150mm
air gap
370mm230mm
390mm
260mm
402 mm
115mm
6
Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
System Identication
Tap Button Identication
Cold
Sparkling
Ambient
Fig.1
Pressure Regulator
CO2Bottle
CO2Tube (Black)
7
Copyright © Puretec Pty Ltd 2018 Puretec Sparq S4 User Guide
System Identication
Fig.2
Note: All lines are 1/4" tube
Water inlet connection
(Blue)
multivalve
Water outlet
(White)
CO2 connector
(Black)
straight connector
Unit power supply
Wiring loom
Smart Tee
Tap
Water inlet
8
Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
Installation
Installation Procedure
VERY IMPORTANT! These installation steps are VERY important and must be
followed in the correct sequence. Remove all packaging before installation including
tubes on the back of the unit (see g. 3 to remove tubes).
1. Select a suitable position for the tap so that it dispenses into the sink bowl with ample
clearance below the outlet and drill a 26mm hole. (Max 30mm)
2. Isolate water supply. Uninstall the connections on the cold water line and connect the
Smart Tee™. Reinstall the previous connection to the tee valve.
3. Connect the multivalve to the Smart Tee™ with a length of BLUE tubing. Please see
Fig.2 for water ow direction.
4. Connect the straight connector to the white tube connected to the tap (see Fig.2).
5. Remove the black plastic nut from the tap thread and connect the wiring loom to the
tap (see Fig.2).
6. Feed the straight adaptor and wiring loom through the tap hole and place tap into
position.
7. Screw the tap nut and tighten making sure the tap is correctly positioned on top.
Fixing the tap to a sink may require more care to align all parts.
Note: For thin bench tops or a sink mount, use the supplied spacer, slipping it up the
thread, followed by the black nut to tighten.
8. Choose the best position for the unit with required 15 cm clearance for ventilation to
the rear and top of the unit. Remember to allow access room for changing lters and
a suitable place where water spillage will not cause damage.
9. With a length of BLUE tubing (enough length to pull out of the cupboard to change
lters if not enough height), connect the multivalve to the inlet at the back of the unit
(see Fig.2).
10. With a length of WHITE tubing (enough length to pull out of the cupboard to change
lters if not enough height), connect the straight adaptor to the water outlet.
11. Attach the wiring loom from the tap to the unit. (see Fig.2)
9
Copyright © Puretec Pty Ltd 2018 Puretec Sparq S4 User Guide
Installation
12. Connect the power cord. (DO NOT TURN POWER ON)
DO NOT turn on the water/and or power supply, this will be done in Step 22-26 of
Cold/Ambient Water Startup on page 10.
13. Position the CO2 bottle as close to the unit as possible, ensuring the bottle is upright.
NOTE: Bottles should always be upright during storage and transit. If the bottle
has been le horizontal, place upright and let stand for 60 minutes for contents
to settle before initializing.
The SPARQ-CO2is NOT rellable
14. Ensure regulator is o by turning the shut-o valve into the closed position.
15. Connect the CO2 bottle to the regulator. Screw the regulator on rmly, (Warning: some
CO2will escape as the valve in the bottle is depressed).
16. Attach the BLACK tube to the CO2connection at the back of the unit and CO2bottle.
(See Fig.1)
DO NOT open the regulator, this will be done in Step 27 of Soda/Sparkling Water
Startup on page 10.
17. Double check all tubes have been connected properly..
18. Check all plumbing ttings have been tightened and all tubing is connected rmly.
19. Ensure there is adequate ventilation around the unit. (15cm)
20. Check all tubes from the undersink unit to the tap, ensure there are no sags or kinks in
the hoses, and any tube sag is minimised as it can cause ow to be reduced.
21. Check all electrical connections are correct and there are no loose wires.
10
Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
Installation
COLD/AMBIENT WATER
22. Turn on the water and check for leaks.
23. Allow tank to ll for 5 minutes.
24. Turn on the power supply at the power point - tap should light up and aer a minute
all lights on the tap will be blue.
25. Flush the lters by pressing on the cold button on the tap rst for 1 minute and
followed by the ambient button for another minute (it is normal for black nes,
cloudiness or micro-bubbles to come through). To activate water ow, press the button
once and the ring light on the top goes green, then press the button again for water
ow.
26. Turn on the COLD power switch on the back of the chiller. The chilling indicator on
the front panel of the unit will turn o once the correct temperature is reached. The
temperature is preset to 4-10 degrees. It takes up to 20 minutes.
1. Cut the tube square and
push in to the tube stop. For
metal tube remove burrs and
chamfer tube end to prevent
O-Ring seal being damaged.
DISCONNECTION PROCEDURE
4. Push collet against body and
slide tube out of tting.
2. Fitting grips before it seals.
Ensure tube is pushed in to
tube stop.
How To Use Quick Connect Fittings
3. Tube is secured in
position.
Fig.3
Otros manuales para Sparq S4
1
Tabla de contenidos
Otros manuales de Dispensador de agua de Puretec
Puretec
Puretec UF10 Series Manual de usuario
Puretec
Puretec Basic SIB Series Manual de usuario
Puretec
Puretec SOL-TA Series Manual de usuario
Puretec
Puretec SOL-E1 Series Manual de usuario
Puretec
Puretec ROS2700 Manual de usuario
Puretec
Puretec CO-RO3 Manual de usuario
Puretec
Puretec QT18 Manual de usuario
Puretec
Puretec SOL-E3 Series Manual de usuario
Puretec
Puretec Softrol E1 Manual de usuario
Puretec
Puretec RO SERIES Manual de usuario
