PURE Highway 400 Manual de usuario
Highway 400
Highway_400_Euro_v1.indb 1 2/24/2016 4:21:23 PM
Highway_400_Euro_v1.indb 2 2/24/2016 4:21:23 PM
EN
DE
FR
IT
NO
DA
NL
1
Thank you for choosing Highway 400. This manual will get you up and
running in no time, and explains how to make the most of your Highway.
We’re constantly improving and adding new features to our products. To
take advantage of any enhancements made since your product was shipped,
please visit support.pure.com where you can find out about the latest product
updates and download the latest version of this user guide in PDF format.
Highway 400
Highway_400_Euro_v1.indb 1 2/24/2016 4:21:23 PM
2
Safety instructions
1. Read and retain these instructions.
2. Heed the warnings given.
3. Follow the operating instructions.
4. Failure to install or use the product in accordance with these instructions may impair the safety of the product and invalidate the warranty.
5. Use only power supplies listed in the user manual/user instructions.
6. Do not fit the wireless controller, receiver or the antenna in such a way that may interfere with the safe operation of the vehicle, the deployment of air bags or other safety product.
7. Avoid running cables and wires near the steering wheel.
8. Do not connect to anything other than the vehicle 12V supply using the supplied adapter.
9. Do not use the product in a manner that would cause careless driving or improper control of your vehicle.
10. Do not immerse in water.
11. Clean only with a dry cloth.
12. Do not place on or near sources of heat, for example heating vents.
13. This product must only be used with the supplied battery types and 12V accessory power adapter.
14. WARNING: The batteries in the wireless controller shall not be exposed to excessive heat such as sunshine, fire or similar.
15. Ensure batteries are fitted with the correct polarity.
16. Attention should be drawn to the environmental aspects of battery disposal.
17. Do not cover any of the vehicle’s ventilation openings as this may impair the vehicle’s ventilation.
18. Do not expose the product to naked flame sources, for example a lighter.
19. This product is intended for use in moderate climates.
20. Ensure that power is removed prior to making any connections to the rear of your vehicle’s head unit. Only turn on your product once connections are made safe. See your vehicle’s
owner’s manual for more information.
If the product is used in a manner not specified by the instructions, the product’s protection could be impaired.
Do not use the product if any damage is noticed.
Product repairs are only allowed to be carried out by competent and authorised personnel.
Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries may
have been swallowed or placed inside any part of the body, seek immediate medical attention.
Symbol Description
This WARNING symbol is used throughout this manual to indicate a potentially serious risk to your personal safety. Obey all safety notices that accompany this symbol to avoid
possible injury or death.
This symbol is used on the product to indicate a caution and that instructions should be read before use.
12V DC
This symbol indicates 12V DC.
1A This symbol indicates a USB socket rated at 1 Amp maximum.
This symbol indicates where the product is switched on or put into standby.
Symbols used on this product
Note: For information on all the other symbols used on the product, see page 12.
Highway_400_Euro_v1.indb 2 2/24/2016 4:21:24 PM
3
EN
Contents
4 Introduction
4 Package contents
5 Installing Highway in your vehicle
5 Important safety notice
6 Considerations before installing Highway
8 Installing the receiver
9 Cable routing overview
10 Connecting the receiver to the power supply
11 Installing the wireless controller
12 Overview
12 Controls
13 Display
13 Switching on and o
14 Switching on Highway for the first time
15 Listening to digital radio
16 Pairing Highway with a phone or tablet
17 Streaming audio stored on your phone
or tablet
18 Streaming from a music streaming service
18 Using Highway with your mobile’s
personal assistant feature
18 Settings
18 Digital radio settings
20 Bluetooth settings
20 Tag add settings
21 Switching between auxiliary connection and FM
transmission
22 Display
22 About
23 Resetting Highway to factory settings
23 Software updates
23 Appendix
23 Troubleshooting
26 Technical specifications
Highway_400_Euro_v1.indb 3 2/24/2016 4:21:24 PM
4
Introduction
Package contents
Receiver
This is intended to be mounted
to the windscreen.
Magnetic grounding tail
This attaches to the receiver
(see page 7).
DAB film antenna
This attaches to the receiver.
Note: The DAB film antenna is
delicate, so be careful not to
bend it.
Wireless controller
The wireless controller
connects to the receiver using
Bluetooth and is used to control
all of Highway’s functions.
Batteries
Two AAA batteries.
Wireless controller bracket
Bracket for positioning the wireless
controller on your dashboard.
Includes sticky pad.
Highway power adapter
Dual USB port 12V accessory
power adapter.
Self-adhesive cable clips
Used for securing any cables.
Cleaning wipe
Used to wipe down surfaces before
fixing any of Highway’s components
into place.
Highway_400_Euro_v1.indb 4 2/24/2016 4:21:25 PM
5
EN
Installing Highway in your vehicle
Important safety notice
For your safety, do not run cables so that they interfere with operation of the vehicle, or through a location that would interfere
with the function of the airbags or other safety equipment, for example seat belts. Do not install any of Highway’s components
in a location that obstructs the view of the driver or in a location where digital radio interference may be caused from the metal
bodywork or other components.
Receiver positioning overview
The receiver is designed to be installed on a window
using the self-adhesive pads provided.
Make sure that you install the receiver in a safe position
where the primary viewing area is not obstructed. Your
windscreen can be divided into separate zones to help
you determine where the receiver can be safely placed:
Zone A is a vertical area 290mm wide, centred on the
steering wheel and contained within the swept area of
the windscreen (this area is 350mm wide on vehicles
over 3.5 tonnes) which must not be incurred upon by
more than 1cm.
Note: Fitting Highway in this area is not recommended.
Zone B is the remainder of the swept area of the
windscreen which must not be incurred upon by more
than 4cm.
The above information is a guide only, for full
information you should consult the relevant country
department of transport guidelines.
Max 1cm
incursion
Max 4cm
incursion
No restriction Zone B Zone A
Suggested position
Highway_400_Euro_v1.indb 5 2/24/2016 4:21:26 PM
6
Considerations before installing Highway
Minimum vehicle requirements
• Fitted audio system with either aux-in (3.5 mm) or FM receiver.
• Standard 12V negative earth power system - not suitable for 24V systems.
Check for the latest Highway software updates
Visit http://www.pure.com/highway-update to see if any software updates are available for your Highway.
Test intended positions of receiver and wireless controller before fixing into place
• Check the cable length to ensure connectors can reach the audio and accessory power outlet positions.
• Temporarily place the receiver and wireless controller in their intended positions and check that Highway is working as
expected. Check the digital radio quality and signal strength (see ‘Info’ on page 22 for more information).
Receiver positioning
• Ensure you can easily access the ‘Reset’ button on the receiver before fitting.
• For best performance we recommend positioning the receiver away from heated screen elements and not on glass panels
that contain metallic UV filters.
Wireless controller positioning
Consider usability and visibility from driving seat and possible mounting points/brackets.
Connecting to your existing audio system
There are two options for installing Highway. You can connect Highway to your audio system’s auxiliary connection or you can
transmit to your audio system wirelessly using an available FM frequency.
• If you want to use an auxiliary cable (recommended for best performance), check for auxiliary inputs on the existing audio
system (this may be on the back on some audio systems). For more information, see your existing audio system’s user guide.
• If you want to use an available FM frequency, select this option during initial Highway setup (see page 14 for more information).
Note: To comply with legal requirements the FM transmitter function of Highway will switch o if no audio is transmitted for a
period lasting over a minute - this includes DAB radio or audio streamed from your phone or tablet. If FM transmission is switched
o you need to re-tune to an active DAB station or stream audio from your phone or tablet.
Highway_400_Euro_v1.indb 6 2/24/2016 4:21:26 PM
7
EN
Receiver overview
Reset button
Used to reset Highway or to start
pairing between the receiver
and the wireless controller, see
’Troubleshooting’ on page 23 for
more information.
Optional detachable magnetic grounding tail
We recommend fitting the magnetic grounding tail if you
can stick it to a metal part of your vehicle’s bodywork.
It can improve DAB reception in areas with poor signal
strength. See the next page for installation guidance.
Power and audio out cable
Status LED
Lights up for a few seconds when you first
switch on Highway. If the LED starts to flash see
’Troubleshooting’ on page 23 for more information.
Film antenna
Clip to the receiver.
Highway_400_Euro_v1.indb 7 2/24/2016 4:21:26 PM
8
Installing the receiver
3. Remove the backing from the receiver (A) and attach to your windscreen.
Note: Make sure that you install Highway in a safe position where the
primary viewing area is not obstructed (see page 5).
4. Gently unpeel the backing of the film antenna (B) and attach to your
windscreen, taking care not to bend it. Apply gentle pressure until the film
antenna is held firmly in position.
Note: Take care not to unclip the film antenna from the receiver when
attaching to your windscreen.
2. Use the supplied cleaning wipe to clean the area of the windscreen
that you want to install the receiver and film antenna on and wait for the
surface to dry. Important: Ensure the surface is completely clean and dry
before adhesion.
Note: The receiver and antenna should be installed at least 40mm from
your vehicle’s metal bodywork.
A
B
1. If you decided to fit the magnetic grounding tail, gently pull down the
front of the roof liner so that there is enough room to push the detachable
magnetic grounding tail through the gap.
Note: Ensure that the magnet on the end of the magnetic grounding
tail makes contact with the roof above your vehicle’s headliner or the
vehicle’s metal bodywork surface.
We recommend installing Highway’s receiver on your vehicle’s windscreen as described below (see page 5 for more information).
Highway_400_Euro_v1.indb 8 2/24/2016 4:21:26 PM
Otros manuales para Highway 400
2
Tabla de contenidos
Idiomas:
Otros manuales de Adaptador de PURE
