Pulsar V041 Manual de usuario
1
CAL. V011, V041
ALARM CHRONOGRAPH
●Analogue time and digital time/calendar
●Regular alarm
●Stopwatch
●Illuminating light (for Cal. V011)
2
DISPLAY AND CROWN/BUTTONS
Pulsar
QUARTZ
CROWN
TIME display
ALARM display TIME/CALENDAR
SETTING display CALENDAR display
STOPWATCH display
●With each press of button A, the digital display changes as follows:
➮➮
➮
➮
➮
B
A
3
SCREW DOWN CROWN
[for models with screw down crown]
Locking the crown
1Turn Crown counterclockwise until you no
longer feel the threads turning.
2Crown can be pulled out.
1Push Crown back in to normal position.
2TurnCrownclockwisewhilepressingitlightly
until tight.
Unlocking the crown
4
DIGITAL TIME/CALENDAR SETTING
Press to show TIME/CALENDAR
SETTING display.
A
B
A
Pulsar
QUARTZ
BSelect the digits to be adjusted.✽
▲
▲
▲
ASet the flashing digits.
B
▲
Press to show TIME/CALENDAR
SETTING display.
A
▲
Press to show CALENDAR display.
✽ Selection of the digits
➾
TIME/CALENDAR
SETTING display
➾
➾Seconds ➾Minutes ➾Hour
12-/24-hour indication
➾
Date
➾
Month
➾
Day
5
ANALOGUE TIME SETTING
●Be sure to set the digital time first before setting the analogue time.
1Pull out when Second hand is at the
12 o’clock position.
2Turn to set Hour and Minute hands.
3Push back when the seconds in the
digital time display count “00”.
CROWN
2
●The illuminating light is activated by continuously pressing button B in the TIME
or CALENDAR display.
* The light intermittently illuminates the display to save the energy of the battery, and
this is not a malfunction.
Pulsar
QUARTZ
1
3
ILLUMINATING LIGHT (for Cal. V011)
6
ALARM
ALARM TIME SETTING
B
BSelect the digits to be adjusted.✽
▲
▲
▲
ASet the flashing digits.
B
▲
Press to show ALARM display.
A
▲
Press to show ALARM display.
Press to activate the alarm setting
function.
✽ Selection of the digits
ALARM display ➾Hour ➾Minutes
➾
B
A
Pulsar
QUARTZ
ALARM display mark
7
ENGAGEMENT/DISENGAGEMENT OF ALARM AND HOURLY TIME SIGNAL
B
A
A
▲
Press to show CALENDAR or
TIME display.
With each simultaneous press,
alarm and hourly time signal are
engagedanddisengagedinorder:
Pulsar
QUARTZ
B
and
A
Alarm mark
Hourly time signal mark
* The alarm rings at the designated
time for 20 seconds. To stop it
manually, press button A or B.
Both engaged
➮
Alarm disengaged
Hourly time signal engaged
➮
Alarm engaged
Hourly time signal disengaged
➮
Both disengaged
8
STOPWATCH
●The stopwatch measures up to 60 minutes in 1/100 second increments.
B
A
Pulsar
QUARTZ
BStop.
▲
▲
BReset.
A
▲
PresstoshowSTOPWATCHdisplay.
BStart.
1/100 seconds
Minutes
Seconds
9
●When setting the flashing digits, they are advanced quickly by keeping button A
pressed, except the seconds and 12-/24-hour indication.
●Seconds digits setting:
The seconds are reset to “00” by pressing button A.
NOTES ON OPERATING THE WATCH
* When the seconds count any number from “30” to “59” and button A is pressed, one
minute is added and the seconds are reset to “00”.
●The changeover between 12- and 24-hour indications is made alternately with each
press of button A.
➾
➾
●When setting the hour in the 12-hour indication, check that AM/PM is properly set. Only
“P” (PM) is displayed. For the AM setting, there is no indication.
●When the time function is displayed in the 24-hour indication, the alarm function is also
displayed in the 24-hour indication.
●If the watch is left untouched in the TIME/CALENDAR SETTING display with the digits
flashing, it will automatically return to the CALENDAR display in 1 to 2 minutes.
●The calendar automatically adjusts for odd and even months except February of leap
years.
DIGITAL TIME/CALENDAR SETTING
10
ANALOGUE TIME SETTING
●When setting the minute hand, first advance it 4 to 5 minute ahead of the desired time
and then turn it back to the exact minute.
●When the crown is pushed in, the minute hand may move slightly. However, this is not
a malfunction.
STOPWATCH
●After the stopwatch has measured 60 minutes, it starts counting again from “00' 00"
oo” as many times as necessary until it is stopped.
●When measuring a long period of time, return the STOPWATCH to the CALENDAR or
TIME display after the stopwatch starts, to prevent any possible mistaken operation.
ALARM
●By pressing button B with the alarm setting function activated, the alarm mark is
displayed and the alarm is automatically engaged.
●When setting the alarm in the 12-hour indication, check that AM/PM is properly set.
Only “P” (PM) is displayed. For the AM setting, there is no indication.
●If the watch is left untouched in the ALARM display or with the digits flashing, it will
automatically return to the CALENDAR display in 1 to 2 minutes.
●Alarm test:
Press and hold buttons A and B at the same time in the TIME or CALENDAR display.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Mirar de Pulsar
Pulsar
Pulsar CAL. VD53 Manual de usuario
Pulsar
Pulsar Y302 Manual de usuario
Pulsar
Pulsar VK83 Manual de usuario
Pulsar
Pulsar V657 Manual de usuario
Pulsar
Pulsar Y182 Manual de usuario
Pulsar
Pulsar VX3K Manual de usuario
Pulsar
Pulsar PJU Series Manual de usuario
Pulsar
Pulsar W860 Manual de usuario
Pulsar
Pulsar Pulsar ANALOGUE Manual de usuario
Pulsar
Pulsar N944 Manual de usuario
Pulsar
Pulsar CAL. W440 Manual de usuario
Pulsar
Pulsar W170 Manual de usuario
Pulsar
Pulsar KINETIC 5M42 Manual de usuario
Pulsar
Pulsar V33J Manual de usuario
Pulsar
Pulsar w863 Manual de usuario
Pulsar
Pulsar VK68 Manual de usuario
Pulsar
Pulsar W621 Manual de usuario
Pulsar
Pulsar GH Series Hoja de información del producto
Pulsar
Pulsar 5Y67 Manual de usuario
Pulsar
Pulsar VX42 Manual de usuario
