Pulsar PSD12050 Manual de usuario
1
PSD12050
PSD 12V/5A Desktop type power supply for CCTV
v.2.0
PL
Edition: 10 from 19.05.2023
Supercedes edition: 9 from 22.01.2018 EN
Features of power supply:
power output 5A/12 V DC*
universal AC input voltage range ~100 –240 V
high efficiency 89%
LED optical signalisation
standby power <0,21W
efficiency level: VI
protections:
SCP short-circuit protection
overvoltage protection (AC input)
overload (OLP)
warranty –2 years from production date
1. Technical description.
1.1. General description.
Stabilized DC power supply is intended for supply CCTV cameras that require stabilised voltage of 12V DC.
The unit has a cable with a DC5.5/2.1 plug. When connected to fuse blocks of LB4/xx/xx or LB8/xx/xx family, power supply unit
can feed more cameras (max. 4 or 8). The unit is protected against short-circuit and overload.
1.2. Technical parameters.
Supply voltage
~100 –240 V; 50/60 Hz
Current consumption
1,2 A
Supply power
60 W max.
Efficiency (average)
89%
Efficiency (10% load)
88%
Output voltage
12 V DC
Output current tAMB<30°C
5A - refer to graph 1.
Output current tAMB=40°C
3,5A - refer to graph 1.
Ripple voltage
100mV p-p max.
Short-circuit protection SCP
electronic, automatic recovery
Overload protection OLP
105-150% of power supply, automatic recovery
Optical signalisation
LED –presence of DC voltage
Operation conditions
temperature 0oC - 40oC
relative humidity 20%...90%, without condensation
Dimensions (LxWxH)
116 x 54 (80) x 35 [mm]
Net/gross weight
0,30 / 0,34 [kg]
Protection class EN 62368-1
II (second)
Lenght of DC cable
1,45m + plug DC5,5/2,1 female
Lenght of AC cable
1,15m + mains plug
Storage temperature
-20ºC...+60ºC
* In order to extend the life of the power supply, the load current of 3,5A is recommended.
Graph 1.
Relation between output current and ambient
Fig.1. Dimension of power supply.
*Refer to graph 1
2
temperature (instantaneous load).
1.3. Accessories.
For power supplies are available accessories - fuse blocks and cable adapter. For details –visit www.pulsar.pl.
2. Installation.
2.1. Requirements.
The power supply shall be mounted by a qualified installer, holding relevant permits and licenses (applicable and required for
a given country) with ~230 V mains supply. Unit should be mounted in confined spaces with normal relative humidity (RH=90%
maximum, without condensing) and temperature from 0°C to +40°C
The power supply shall be mounted in a close casing (a cubicle, a terminal device) and in order to fulfill LVD and EMC
requirements the rules for power supplies, encasing and shielding shall be observed according to application.
2.2. Installation procedure.
1. Connect the DC output to the load/loads.
2. Connect the power supply unit to the AC line. The power supply has to be installed in such way to keep the air flow
around the supply unit.
3. After tests and operation control are performed, the casing (cubicle) shall be closed etc.
3. Maintenance.
Any and all maintenance operations may be performed following the disconnection of the power supply from the power
network. The power supply does not require any specific maintenance procedures, however, in the case of significant level of dust, it
should be cleaned with the compressed air.
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to European Union WEEE Directive, waste electrical and electronic equipment should
be disposed of separately from normal household waste.
Pulsar sp. j.
Siedlec 150,
32-744 Łapczyca, Poland
Tel. (+48) 14-610-19-45
e-mail: [email protected]
http:// www.pulsar.pl
Otros manuales de Fuente de alimentación de Pulsar
Pulsar
Pulsar PSBOC501235 Manual de usuario
Pulsar
Pulsar PSBEN 1012B/LCD Manual de usuario
Pulsar
Pulsar PSG3 Series Manual de usuario
Pulsar
Pulsar HPSBOC 5048C Manual de usuario
Pulsar
Pulsar RED POWER EN54-7A28 Manual de usuario
Pulsar
Pulsar AWZ 110 Manual de usuario
Pulsar
Pulsar PSDCSEP-12V4x1A Manual de usuario
Pulsar
Pulsar PSA12010 Manual de usuario
Pulsar
Pulsar PSCLB13830 Manual de usuario
Pulsar
Pulsar PWB Series Manual de usuario
Pulsar
Pulsar PS-12V10A Manual de usuario
Pulsar
Pulsar PSCV2012 Manual de usuario
Pulsar
Pulsar R812T Manual de usuario
Pulsar
Pulsar HPSB 11A12C Manual de usuario
Pulsar
Pulsar PSDC 08128 Manual de usuario
Pulsar
Pulsar PS-2002470 Manual de usuario
Pulsar
Pulsar Blue Power PSBS 2012B Manual de usuario
Pulsar
Pulsar GREEN POWER plus HADOC 3012C Manual de usuario
Pulsar
Pulsar DSOP24V Manual de usuario
Pulsar
Pulsar PSDC 04124 Manual de usuario
