Pulsar Blue Power PSBS 5012E Manual de usuario

PSBS 5012E

v.1.1

PSBS 13,8V/5A/65Ah/OC

Buffer switch mode power supply unit

with technical outputs.

EN**

Edition: 7 from 03.11.2016

Supercedes edition: 6 from 01.06.2016

www.pulsar.pl PSBS5012E BLUE POWER

PSU features:

uninterruptible power supply DC 13,8V/5A

battery housing: 65Ah/12V

supply voltage AC 230V

high efficiency 76%

low voltage ripple

battery charging and maintenance control

deep discharge battery protection (UVP)

battery charging current 0,5A/1A/2A/3A, jumper

selectable

START button to start the battery

battery output protection against short-circuit and

reverse connection

LED indication

EPS technical output of 230V power failure

–OC type

PSU technical output indicating PSU failure

–OC type

LoB technical output indicating low battery voltage

–OC type

Optional installation of the MPSBS relay module

changing technical outputs of the OC type to relay

type

adjustable times of 230V AC failure indication

Protection type:

SCP short-circuit protection

Overheat protection OHP

surge protection

Tamper protection: enclosure opening and

detachment from the wall

overload protection OLP

warranty - 5 years from the production date

TABLE OF CONTENTS:

1. Technical description.

1.1 General description

1.2 Block diagram

1.3 Description of components and connectors

1.4 Technical parameters

2. Installation.

2.1 Requirements

2.2 Installation procedure

3. Power supply operation indication.

3.1 Optical indication of operation

3.2 Technical outputs

3.3 Relay technical outputs

4. Service and operation

4.1 Overload or short-circuit the power supply output (SCP activation)

4.2 Running the PSU from the battery.

4.3 Deep discharge battery protection UVP.

4.4 Maintenance

1. Technical description.

1.1 General description.

A buffer PSU is designed for uninterrupted supply of devices requiring stabilized voltage of 12V DC (+/-

15%). The PSU supplies voltage of U=13,8V DC and total current capacity of:

1. Output current 5A + 0,5A battery charging

2. Output current 4,5A + 1A battery charging

3. Output current 3,5A + 2A battery charging

4. Output current 2,5A + 3A battery charging

Total current + battery is max. 5,5A

In case of mains power loss, the unit will instantly switch to battery operation. The PSU is enclosed in a

metal casing (color RAL 9003) with battery housing for 65Ah/12V batteries. The enclosure is fitted with a micro

switch indicating door opening (front cover) and the detachment from the wall.

www.pulsar.pl PSBS5012E BLUE POWER

OPTIONAL POWER SUPPLY CONFIGURATIONS:

(visualization available at www.pulsar.pl)

PSBS 5012E Battery 65Ah.

1. Buffer power supply PSBS 13,8V/relay module MPSBS/65Ah

- PSBS 5012E + MPSBS + 65Ah

2. Buffer power supply PSBS 13,8V/4x1A/65Ah

- PSBS 5012E + LB4 4x1A (AWZ575 or AWZ576) + 65Ah

3. Buffer power supply PSBS 13,8V/8x0,5A/65Ah

- PSBS 5012E + LB8 8x0,5A (AWZ578 or AWZ580) + 65Ah

4. Buffer power supply PSBS 13,8V/12V/5A/65Ah

- PSBS 5012E + RN500 (13,8V/12V) + 65Ah

5. Buffer power supply PSBS 13,8V/2x12V/2x2,5A/65Ah

- PSBS 5012E + 2xRN250 (13,8V/12V) + 65Ah

PSBS 5012E Battery 40Ah.

1. Buffer power supply PSBS 13,8V/relay module MPSBS/40Ah

- PSBS 5012E + MPSBS + 40Ah

2. Buffer power supply PSBS 13,8V/4x1A/40Ah

- PSBS 5012E + LB4 4x1A (AWZ575 or AWZ576) + 40Ah

3. Buffer power supply PSBS 13,8V/8x0,5A/40Ah

- PSBS 5012E + LB8 8x0,5A (AWZ578 or AWZ580) + 40Ah

4. Buffer power supply PSBS 13,8V/16x0,3A/40Ah

- PSBS 5012E + 2xLB8 16x0,3A (AWZ577 or AWZ580) + 40Ah

5. Buffer power supply PSBS 13,8V/12V/5A/40Ah

- PSBS 5012E + RN500 (13,8V/12V) + 40Ah

6. Buffer power supply PSBS 13,8V/2x12V/2x2,5A/40Ah

- PSBS 5012E + 2xRN250 (13,8V/12V) + 40Ah

7. Buffer power supply PSBS 13,8V/12V/16x0,3A/40Ah

- PSBS 5012E + RN500 (13,8V/12V) + 2xLB8 2x8x0,3A (AWZ577 or AWZ580) + 40Ah

8. Buffer power supply PSBS 13,8V/12V/8x0,5A/40Ah

- PSBS 5012E + RN500 (13,8V/12V) + LB8 8x0,5A (AWZ578 or AWZ580) + 40Ah

9. Buffer power supply PSBS 13,8V/12V/4x1A/40Ah

- PSBS 5012E + RN500 (13,8V/12V) + LB4 4x1A (AWZ575 or AWZ576) + 40Ah

10. Buffer power supply PSBS 13,8V/2x5V÷7,4V/2x2A/40Ah

- PSBS 5012E + 2xDCDC20(2x5V÷7,4V/2x2A) + 40Ah

1.2 Block diagram (Fig.1).

Fig.1. Block diagram of the PSU.

www.pulsar.pl PSBS5012E BLUE POWER

1.3 Description of components and power supply terminals (Table 1, Fig.2).

Table 1. Components of the Power supply PCB (Printed Circuit Board) (see Fig. 2).

Component

no.

Description

PBAT Jumper –configuration of discharged battery disconnection system (UVP)

PBAT = discharged battery disconnection system OFF

PBAT = discharged battery disconnection system ON

TAC Jumper- setting the delay time for AC power failure indication

TAC = delay time T= 60s

TAC = delay time T= 10s

Description: jumper on, jumper off

START button (running the PSU from the battery)

VADJ potentiometer, DC 12 ÷ 14,5V voltage adjustment

FBAT fuse in the battery circuit, F6,3A / 250V

Terminals:

~AC~ –AC power input

EPS –technical output of AC power failure indication

hi-Z state = AC power failure

0V state = AC power - O.K.

PSU –technical output of PSU failure indication

hi-Z state = failure

0V state = PSU status O.K.

LoB –technical output of low battery voltage indication

hi-Z state = battery voltage UBAT <11,5V

0V state = battery O.K.

+BAT- –terminals for battery connection

+AUX- –DC power output, (+AUX= +U, -AUX=GND)

Description: hi-Z –high impedance, 0V –connection to the ground GND

LEDs –optical indication:

AC –AC power

LB –battery charging

AUX –output voltage DC

Optional, external optical indication output terminal

IBAT Jumper; - battery charging current configuration

J1= J2= J3= Ibat =0,5A

J1= J2= J3= Ibat =1A

J1= J2= J3= Ibat =2A

J1= J2= J3= Ibat =3A

Description: jumper on, jumper off

Fig. 2. The view of the Power supply PCB.

www.pulsar.pl PSBS5012E BLUE POWER

Table 2. Components of the PSU (See Fig. 3).

Component no.

Description

Isolation transformer

Printed Circuit Board (see Table 1, Fig. 2)

TAMPER; micro switch of tamper protection (NC)

FMAINS fuse in the power supply circuit 230V, T3,15A / 250V

L-N power supply connector, 230V AC, PE protective connector

Battery connectors: positive: +BAT = red, negative: - BAT = black

Fig.3. The view of the PSU.

1.4 Technical parameters:

- Electrical parameters (Table 3)

- Mechanical parameters (Table 4)

- Safety of use (Table 5)

- Operation parameters (Table 6)

Table 3. Electrical parameters

PSU type:

A (EPS - External Power Source)

Mains supply

230V AC / 50Hz (-15%/+10%)

Current consumption

0,57A @230V AC

PSU’s power

76W

Efficiency

76%

Output voltage

11V÷13,8V DC –buffer operation

10V÷13,8V DC –battery operation

Output current

5A + 0,5A battery charging

4,5A + 1A battery charging

3,5A + 2A battery charging

2,5A + 3A battery charging

Output voltage adjustment range

12÷14,5V DC

Ripple voltage

60mV p-p max.

PSU current consumption

15 mA

Battery charging current

0,5A / 1A / 2A / 3A –jumper selectable

Short-circuit protection SCP

Electronic - current limitation and/or activation of the FBAT

melting fuse in the battery circuit (failure requires fuse

www.pulsar.pl PSBS5012E BLUE POWER

replacement)

Automatic return

Overload protection OLP

110-150% of the PSU power, manual restart (failure

requires the disconnection of the DC output)

Battery circuit protection SCP and reverse

polarity connection

T6,3A- current limitation, the FBAT melting fuse (failure

requires fuse replacement)

Surge protection

varistors

Deep discharge battery protection UVP

U<10V (± 0,5V) – disconnection of battery terminal

Tamper protection:

- TAMPER output indicating enclosure opening or

detachment from the wall

- micro switch x 2, NC contacts (enclosure closed and

mounted to the mounting base), 0,5A@50V DC (max.)

Optical indication: front panel of the PSU

- AC OK.; LED indicating the AC power status

- DC OK.; LED indicating the DC supply at the PSU

output

- BAT OK.; LED indicating the battery voltage

- red, normal operation: permanently illuminated,

failure: off

- green, permanently illuminated, failure: off

- green, permanently illuminated,

failure: off

Technical outputs:

- EPS; output indicating AC power failure

- PSU; output indicating no DC power/PSU failure

- LoB output indicating low battery voltage

- OC type: 50mA max.

Normal operation: L state (0V),

failure: hi-Z state,

- delay time 10s/60s (+/-20%) –jumper selectable TAC

- OC type: 50mA max.

Normal operation: L state (0V),

failure: hi-Z state,

- OC type, 50mA max.

Normal operation (UBAT >11,5V): L state (0V),

failure (UBAT <11,5V): hi-Z state

The power supply unit does not feature a battery detection

function.

Fuses:

- FMAINS

- FBAT

T 3,15A / 250V

T 6,3A / 250V

Table 4. Mechanical parameters.

Enclosure dimensions

400 x 370 x 170+8 (WxHxD) [mm] (+/- 2)

Mounting

See Fig., 3

Battery housing

65Ah/12V (SLA) max.

350x175x165mm (WxHxD) max

Net/gross weight

8,60kg / 9,90kg

Enclosure

Steel plate, DC01 0,7mm color RAL 9003

Closing

Cylindrical screw (at the front), (lock assembly possible)

Terminals

Mains supply 230V AC: Ф0,51÷2 (AWG 24-12)

Outputs: Ф0,41÷1,63 (AWG 26-14)

BAT battery outputs: 6,3F-2,5, 30cm

TAMPER output: cables, 25cm

Notes

The enclosure does not adjoin the mounting surface so that cables can be led.

Convection cooling.

Table 5. Safety of use.

Protection class PN-EN 60950-1:2007

I (first)

Protection grade PN-EN 60529: 2002 (U)

IP20

Insulation electrical strength:

- between input (network) circuit and the output circuits of the PSU (I/P-O/P)

- between input circuit and PE protection circuit (I/P-FG)

- between output circuit and PE protection circuit (O/P-FG)

3000 V/AC min.

1500 V/AC min.

500 V/AC min.

Insulation resistance:

- between input circuit and output or protection circuit

100 MΩ, 500V/DC

www.pulsar.pl PSBS5012E BLUE POWER

Table 6. Operation parameters.

Environmental class

Operating temperature

-10ºC...+40ºC

Storing temperature

-20ºC...+60ºC

Relative humidity

20%...90%, no condensation

Vibrations during operation

unacceptable

Surges during operation

unacceptable

Direct insolation

unacceptable

Vibrations and surges during transport

According to the PN-83/T-42106 standard

2. Installation.

2.1 Requirements.

The buffer PSU should be mounted by a qualified installer, holding relevant permits and licenses

(applicable and required for a given country) for 230V/AC and low-voltage installations. The unit should be

mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative humidity

(RH=90% maximum, no condensation) and temperature range from -10°C up to +40°C. The power supply should

operate in a vertical position in order to provide free and convectional air flow through ventilating holes of the

enclosure.

The power supply load balance should be done before installation:

1. Output current 5A + 0,5A battery charging

2. Output current 4,5A + 1A battery charging

3. Output current 3,5A + 2A battery charging

4. Output current 2,5A + 3A battery charging

Total current + battery is max. 5,5A

The power supply is designed for a continuous operation and is not equipped with a power-

switch. Therefore, an appropriate overload protection in the power supply circuit should be provided. Moreover, the

user should be informed how to disconnect the power supply unit from the mains supply (usually by assigning an

appropriate fuse in the fuse box). The electrical system shall be made in accordance with applicable standards and

regulations.

2.2 Installation procedure.

1. Before installation, make sure that the voltage in the 230V power-supply circuit is cut off.

2. Mount the PSU in a selected location. The tamper bracket, located in the central part of the housing (see

Fig. 3 [3]), signaling the attempts to detach the PSU from the mounting surface, should be screwed to the

mounting surface.

Fig. 4. Mounting the tamper bracket.

3. Connect the power cables (230V AC) to the L-N terminals of the PSU. Connect the ground wire to the

terminal marked with the PE symbol (power supply module connector). Use a three-core cable (with a

yellow and green PE protection wire) to make the connection. The power cables should be connected to

the appropriate terminals on the connection board through the bushing.

www.pulsar.pl PSBS5012E BLUE POWER

AC OK:

on –The PSU supplied with 230V AC voltage

off –no 230V AC mains supply

DC OK:

on –DC voltage at the AUX output

off - no DC voltage at the AUX output

BAT OK:

on –battery voltage UBAT > 11,5V

off –battery voltage UBAT < 11,5V

The shock protection circuit shall be done with a particular care: the yellow and green

wire coat of the power cable should be connected to the terminal marked with

the PE symbol. Operation of the PSU without the properly made and fully operational

shock protection circuit is UNACCEPTABLE! It can cause damage to the equipment or

an electric shock

4. Connect the receiver cables to the AUX terminals at the power supply board.

5. If needed, connect the device cables to the technical outputs:

- EPS; technical output indicating AC power failure

- PSU; technical output indicating PSU failure.

- LoB; technical output indicating low battery voltage

- Optional installation of the MPSBS relay module changing technical outputs of the OC type to relay type

(page 9, section. 3.3)

6. Use the IBAT jumper to set the maximum battery charging current, taking into account the battery

parameters.

7. Use the PBAT jumper to set to turn on/off deep discharge battery protection U<10V (+/-5%). Deep

discharge battery protection is ON when the PBAT jumper is OFF.

8. Mount the battery in the battery compartment of the enclosure (Fig. 3). Connect the batteries with the PSU

paying special attention to the correct polarity.

9. Switch on the 230V AC supply. The corresponding LEDs on the power supply PCB should be ON: red AC

and green AUX. The yellow LB LED should light up while charging.

10. Check the output voltage (the power supply voltage without load should be 13,6V ÷ 13,9V, 11V ÷ 13,8V

while battery charging). If the voltage requires adjustment, use the VADJ, potentiometer while monitoring the

voltage at the AUX output of the power supply.

11. Check the current consumption of the receivers, taking into account the battery charging current, so as not

to exceed the total current efficiency of the PSU (section 1.1).

12. Close the cover after installing and checking the operation of the power supply.

3. Power supply operation indication.

3.1 Optical indication.

The PSU is fitted with 3 LED lights at the front panel:

Additionally, the PSU is fitted with 3LED lights indicating the operating status: AC, LB and AUX at the PCB

of the PSU:

AC- red LED: is permanently illuminated during normal operation (AC power ON). No AC power is

indicated by turning off the LED.

LB- yellow LED: indicates battery charging. The light intensity depends on the charging current.

AUX- green LED: indicates DC power status at the PSU output. During normal operation, it is permanently

illuminated. In case of short-circuit or output overload the LED is off.

www.pulsar.pl PSBS5012E BLUE POWER

3.2 Technical outputs.

The PSU has three indication outputs:

EPS - technical output indicating 230V AC power failure.

The output indicates 230V AC power failure. Under normal status –with the 230V AC supply on, the output

is shorted to ground GND. In case of power failure, the PSU will switch the output into hi-Z high impedance

state after a time set by the TAC jumper.

PSU –output indicating PSU failure.

The output indicates PSU failure. Under normal status (correct operation) the output is shorted to ground

GND. If there is no DC voltage at the output (eg short circuit), the output is switched into hi-Z high

impedance state.

PSU failure can be caused by the following events:

- Short circuit at the output

- Output overload

- DC/DC voltage converter failure

- Under voltage protection activation

LoB –output indicating low battery voltage.

The output indicates low battery voltage. Under normal status (UBAT > 11,5V) the output is shorted to

ground GND, when the battery voltage drops too low (UBAT < 11,5V) the output is switched into hi-Z high

impedance state.

The power supply unit does not feature a battery detection function. In the case of no battery or non battery

connected, the output is in the normal mode.

The power supply technical outputs are open collector (OC) type, as shown schematically below.

Fig. 5. Electrical diagram of the OC technical outputs.

3.3 Relay technical outputs.

If the OC type outputs are not sufficient to control the unit, it is possible to use the MPSBS relay module

changing technical outputs of the OC type to relay type.

Fig. 6. The diagram of connecting the MPSBS module.

www.pulsar.pl PSBS5012E BLUE POWER

4. Service and operation.

4.1 Overload or short-circuit of the power supply output (SCP activation).

The AUX output of the PSU is protected against short-circuit by PTC polymer fuse. If the power supply load

current exceeds Imax. (110% ÷ 150% @ 25°C of the PSU power), automatic disconnection of the output voltage,

indicated by switching off the green LED, takes place. To restore the voltage at the output, disconnect the load

from the power supply output for approximately 1 minute.

In case of a short-circuit at the AUX, BAT output or reverse battery connection, the FBAT fuse in the battery

circuit becomes permanently damaged. The voltage restoration at the BAT output requires fuse replacement.

4.2 Running the PSU from the battery.

The power supply is equipped with the button on the PCB allowing to run the PSU from the battery, when

needed. To do that, press and hold the START button on the unit board for 1 second.

4.3 Deep discharge battery protection UVP.

The power supply is equipped with deep discharge battery protection (UVP). If the voltage at the battery

terminals drops below 10V±0.5V during battery-assisted operation, the batteries will be disconnected. The battery

protection is on when the PBAT jumper is off.

Caution.

It is not recommended to disable UVP since deep discharge of the batteries reduces their ability to

store energy, their capacity and lifetime.

4.4 Maintenance.

All maintenance procedures can be performed after disconnecting the power supply from the power

network. The PSU does not require any specific maintenance; however, its interior should be cleaned with

compressed air if used in dusty conditions. In case of fuse replacement, use only compatible replacement parts.

Otros manuales para Blue Power PSBS 5012E

Tabla de contenidos

Otros manuales de Fuente de alimentación de Pulsar

Pulsar

Pulsar PSBOC3004850 Manual de usuario

Pulsar

Pulsar PSBSEP04124 Manual de usuario

Pulsar

Pulsar AWZ 333 Manual de usuario

Pulsar

Pulsar PSCLB13810 Manual de usuario

Pulsar

Pulsar PSD12020 Manual de usuario

Pulsar

Pulsar HPSB 5524D Manual de usuario

Pulsar

Pulsar PSBEN 3012D/LCD Manual de usuario

Pulsar

Pulsar BLACK POWER PSBEN 2012C Manual de usuario

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Pulsar

Pulsar PSCV5012 Manual de usuario

Pulsar

Pulsar PSB1552455 Manual de usuario

Pulsar

Pulsar DIN 1220 Manual de usuario

Pulsar

Pulsar PSCV5012 Manual de usuario

Pulsar

Pulsar PSBEN 2024C Manual de usuario

Pulsar

Pulsar PSA12010 Manual de usuario

Pulsar

Pulsar PS402415 Manual de usuario

Pulsar

Pulsar HPSB 3524C Manual de usuario

Pulsar

Pulsar PSBEN 10A12C Manual de usuario

Pulsar

Pulsar PSDC08128T Manual de usuario

Pulsar

Pulsar PSCC10700 Manual de usuario

Pulsar

Pulsar PSA12030 Manual de usuario

Pulsar

Pulsar PSBEN 5024C/LCD Manual de usuario

Pulsar

Pulsar PSBEN 5012E Manual de usuario

Pulsar

Pulsar PSC13008 Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario