Proware PW-MN421 Manual de usuario
PW-MN421
Wireless Lite-N USB Module
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark
of PROWARE TECHNOLOGIES CO., LTD. Other brands and product names are trademarks
or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from
PROWARE TECHNOLOGIES CO., LTD. Copyright © 2013 PROWARE TECHNOLOGIES CO.,
LTD. All rights reserved.
http://www.proware.com.cn
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
National Restrictions
2400.0-2483.5 MHz
Country Restriction Reason/remark
Bulgaria General authorization required for outdoor use and
public service
France
Outdoor use limited to 10 mW
e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy If used outside of own premises, general authorization
is required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented
This subsection does not apply for the geographical
area within a radius of 20 km from the centre of
Ny-Ålesund
Russian Federation Only for indoor applications
Note: Please don’t use the product outdoors in France.
CONTENTS
Package Contents....................................................................................................1
Chapter 1Introduction...........................................................................................2
1.1Overview of the Product.......................................................................................... 2
1.2Features.................................................................................................................. 2
Chapter 2Installation Guide..................................................................................3
2.1Hardware Installation .............................................................................................. 3
2.2Software Installation................................................................................................ 3
Appendix A: Specifications.....................................................................................9
Appendix B: Glossary............................................................................................10
Package Contents
The following items should be found in your package:
¾PW-MN421 Wireless Lite-N USB Module
)Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.
Conventions:
The ‘Module’ mentioned in this user guide stands for PW-MN421 Wireless Lite-N USB Module
without any explanations.
1
PW-MN421 Wireless Lite-N USB Module
2
Chapter 1 Introduction
Thank you for choosing the PW-MN421 Wireless Lite-N USB Module!
1.1 Overview of the Product
The module is an 802.11n client device. It is mainly designed to provide a high-speed and
unrivaled wireless performance for wireless embedded system application. With a faster wireless
connection, you can get a better Internet experience without the cost of running network cables.
With the 802.11n technology, the PW-MN421’s auto-sensing capability allows high packet
transfer rate of up to 150Mbps for maximum throughput. It has good capability on anti-jamming,
and it can also interoperate with other wireless (802.11b/g/n) products. The module supports
WEP, WPA and WPA2 encryption to prevent outside intrusion and protect your personal
information from being exposed.
With unmatched wireless performance, reception, and security protection, it is easily to be used in
different kinds of wireless embedded system for its size and portable.
1.2 Features
¾Complies with IEEE802.11n, IEEE802.11g, IEEE802.11b standards
¾Supports WPA/WPA2 data security, IEEE802.1x authentication, TKIP/AES encryption,
64/128/152-bit WEP encryption
¾Supports high rate of up to 150Mbps for maximum throughput, supports automatically
adjust to lower speeds due to distance or other operating limitations
¾Provides USB interface
¾Supports Ad-Hoc and Infrastructure modes
¾Good capability on anti-jamming
¾Supports roaming between access points when configured in Infrastructure mode
¾Ease to configure and provides monitoring information
¾
Supports Windows XP, Vista, 7
PW-MN421 Wireless Lite-N USB Module
3
Chapter 2 Installation Guide
2.1 Hardware Installation
PW-MN427_56I has a 4-Pin onboard connector to transmit USB signal, and it is mainly
designed to provide stability wireless function and performance for your system.
For installation, you must be sure to connect this module to your device or system’s compatible
connector, sometimes you should use a connecting wire first. Then, the promoted Found New
Hardware Wizard will pop up if the Module is installed correctly.
2.2 Software Installation
Windows XP, Vista, 7 are supported. This user guide takes Windows XP for example.
1. Please run the Setup program of the module. Then you will see Figure 2-1.
PW-MN421 Wireless Lite-N USB Module
4
Figure 2-1
2. Soon, Figure 2-2 will display after a moment. Click Next to continue.
Figure 2-2
3. After that, you should choose a Setup type. It is recommended that you select Install
Client Utilities and Driver. Select Install Driver Only to install driver only, select Make
Driver Installation Diskette(s) to make the diskette(s) as the installation driver (shown in
Figure 2-3). Click Next to continue.
PW-MN421 Wireless Lite-N USB Module
5
Figure 2-3
4. Click Browse… to change the destination location for the software, then click Next in the
screen below (shown in Figure 2-4).
Figure 2-4
5. After that, select the program folder, you should create a new folder name or select one
from the Existing Folders list. It is recommended that you keep the default setting. Click
Next to continue the installation.
Tabla de contenidos
Otros manuales de Adaptador de Proware
