Provo Craft Yudu Manual de usuario

www.whatdoYudu.com

model yudu

USER MANUAL •MANUEL D’UTILISATEUR

MANUAL DEL USUARIO •BENUTZER HANDBUCH

START

INTRODUCTION

The Yudu™ screen-printing system is the easiest, cleanest way

to let everyone know who you are—and how you see the world.

Unsilence yourself today—with apparel, home décor, art prints,

posters, cards, schoolwork, and more. This instruction manual will

walk you through the screen-printing process so you can use Yudu

to let your voice be heard.

UNPACK YOUR BOX

Your box should contain the following:

A. Yudu machine

B. Adult t-shirt platen

C. Blank ink-jet transparency

D. 110 mesh screen

E. Squeegee

F. 2 ﬂ oz black ink

G. Platen adhesive sheet

H. Instructional DVD

I. Quick start guide

J. Emulsion sheet

START

OTHER USEFUL ITEMS TO

HAVE WHILE SCREEN-PRINTING

Along with the items that come with your Yudu machine, you may

ﬁnd it useful to have access to these items.

•Clear tape (2"wide is preferable)

•Yudu Blockout

•Yudu Emulsion Remover

•Yudu Registration Panels (for multicolored designs)

•Spray bottle

•Sponge

•Large sink or tub with spray head

•Old rags or paper towels (for cleanup)

•Low light room or light safe environment

•Plastic knife or popsicle stick (for ink salvage)

•Hair dryer

•Iron

•Extra cloth or white paper (to use during heat setting)

•Baby wipes

•Household item weighing about 5 lbs (to use during

screen exposure)

YUDU MACHINE, DISPLAY, AND BUTTONS

Expose

Fan

Light Table

Add Time

Subtract Time

Registration Posts

(1 in each corner of

topside of lid)

Light Table

Drying Rack

Lid

Display

Registration Posts

(1 in each corner)

Platen Posts

START

***READ ALL INSTRUCTIONS BEFORE USING***

**ONLY USE YUDU INKS**

DANGER

The Yudu machine is electrically live even when the switch is off.

To reduce risk of death or injury by electric shock:

1. Always unplug appliance immediately after using.

2. Do not place or store appliance where it can fall or be pulled

into a tub or sink.

3. Do not place in, or drop into, water or other liquid.

4. If an appliance falls into water, unplug it immediately. Do not

reach into the water.

WARNING

To reduce risk of burns, electrocution, ﬁre, or injury to persons:

1. This appliance should never be left unattended while plugged in.

2. Use this appliance only for its intended use as described in this

manual. Do not use attachments not recommended by

the manufacturer.

3. Never operate this appliance if it has a damaged cord or

plug, if it is not working properly, or if it has been dropped,

damaged, or dropped into water.

4. Keep the cord away from heated surfaces. Do not pull, twist, or

wrap line cord around machine, even during storage.

5. Never block the air openings of the appliance or place it on a soft

surface, such as a bed or couch, where the air openings may

be blocked. Keep the air openings free of lint, dust, and other

obstructions.

6. Do not use with a voltage converter.

CAUTION

NEVER allow the power supply cord to be pulled, twisted,

or severely bent. Never wrap the cord around the appliance.

Damage will occur at the high ﬂex point of entry into the machine,

causing it to rupture and short. Inspect the cord frequently

for damage. Stop use immediately if damage is visible or

unit stops or operates intermittently. No repairs should be

attempted by the consumer.

STORAGE

When not in use, appliance should be disconnected, allowed to

cool, and stored in a safe, dry location. Do not wrap cord around

appliance. Allow the cord to hang or lie loose and straight at the

point of entry into the appliance.

START

TEXTILE INKS

•Very runny

•Couldn’t easily save ink

•

Ink bled through t-shirt onto platen

YUDU INKS

•

Perfect consistency to produce a nice,

crisp image

•Screw off top allows for ink salvage

•Ink easily washes out of screen when

cleaned up prior to ink drying

•Allows screens to be saved for

future use

•Water-based inks make cleanup easy

FABRIC PAINT

•Design was faded

•Not a nice, crisp image

•Ink dried instantly onto screen and

ruined screen

- Hard to clean off

- Plugged up image on screen

•

Stained squeegee

FASHION PAINT

•Opening in bottle is too small to

reuse ink

•Ink plugged up and ruined screen

RUINED SCREEN

This screen has been washed, but the

fabric inks have remained lodged in the

screen, ruining it for further use.

INK TESTING RESULTS

CAUTION

Do not use generic textile or fabric inks with your Yudu screens.

Using non-Yudu inks can permanently damage your screen.

DESIGN

Create design on computer.

For multicolored designs, separate

colors into different layers.

TIP: Not all designs need to be created

on the computer. Be creative by drawing

freehand on your transparency.

1. CREATE DESIGN

Print design in black on Yudu blank

transparencies. For multicolored designs,

print each layer separately.

Print on dull side of transparency. A

moist ﬁnger will stick to dull side of

transparency.

TIP: For multicolored designs, you may

ﬁnd it helpful to create registration marks

on each layer in the exact same spot.

This will allow you to easily line up layer 1

and layer 2 later.

LAYER 1

LAYER 2

RECOMMENDED MATERIALS TO SCREEN-PRINT

Yudu inks are designed for use with textile fabric: cotton, 50/50 poly/

cotton blend, and similar fabrics. Yudu water-based inks are

water soluble and easy to clean up.

OTHER MATERIALS TO TRY

-Wood

-Paper

-Porous fabric

CAUTION

Printing on materials other than textile fabric may yield

different results.

PREPARE

2. PREPARE SCREEN

TIP: The back of your screen is completely

ﬂush with the metal edge. The front is

slight lower than the edge.

TIP: You can use a spray bottle to wet screen.

TIP: Run squeegee up and down back and

front of screen to remove excess water.

Spray the screen with water. It should be

completely wet, but not dripping.

Remove the emulsion sheet from the

black plastic bag in a dimly lit area.

TIP: There are two sides to the sheet, one

shiny and one dull. If you can’t tell which

is which, wet your ﬁngers and touch the

corner. The sticky side is the dull side.

TIP: Center the emulsion on the screen.

not allow mesh to touch anything while

applying emulsion.

Apply the dull/sticky side to the back of

the wet screen.

Make sure the screen is clean and free of

dust, lint, and oil.

All screen preparation MUST be done

on the back.

FRONT

CLEAN

BACK

DIRTY

3. APPLY EMULSION TO SCREEN:

PREPARE

Adhere transparency, printed side up,

to the glass on the Yudu machine using

clear tape.

For single color designs, go to "Exposing

Screen" on page 8.

Tape second design layer to second registration

panel, stacking the images, and ensuring it is

registered with ﬁrst layer. Repeat for each

design layer.

When design layers are secured to registration

panels, remove all but the ﬁrst panel.

5. MULTICOLORED DESIGNS:

Press light table button.

4. SINGLE COLORED DESIGNS:

Place ﬁrst registration panel on

registration posts.

Mount ﬁrst design layer to registration

panel with clear tape.

Run squeegee over the shiny surface of

the emulsion.

TIP:Inspectfront ofthescreen for anybubbles ordry

areas. Dry areas will have a spiderweb pattern. Use spray

bottle with water to lightly mist any dry areas. Squeegee

both sides of screen to eliminate excess water prior to

drying. Dry edges of screen with a paper towel or cloth.

Place screen in drying rack of Yudu machine.

Press fan button to begin a 20 minute drying

cycle. The fan will stop and the machine will beep at the

close of the cycle. In drier climates the screen may dry

after as little as one cycle. In more humid climates the

drying process may require several cycles. For humid

climates you may blot moisture from the underside

of the screen with a dry cloth towel and/or squeegee

excess moisture from the screen to speed the drying

process. Test for dryness before moving on to the next

steps. After emulsion has dried, remove plastic ﬁlm.

TIP: A hair dryer can be used to accelerate the

drying process.

TIP: Leaving door open while drying will speed up

the process. Repeat the drying process if necessary.

PREPARE

Add extra weight to top of platen to

ensure proper exposure (approximately

5 lbs). Using up and down buttons on

timer, set exposure time (approximately

8 minutes).

Press exposure button.

WARNING: Turn off machine for 1 minute

between exposures to allow unit to

cool down.

For multicolored designs, use new

screen and repeat exposure, wash, and

drying steps for each artwork layer.

When machine beeps and exposure light

turns off, remove weight, platen, and

screen from machine. Exposed emulsion

will turn from green to blue after

exposure. Design will remain green.

Wet both sides of screen with COOL

water and let it sit for a minute. Spray

screen with cool water to remove green

emulsion from design area. It may be

necessary to gently rub both sides of

screen by hand or use a soft sponge to

remove emulsion in detailed design areas.

Place screen front side up/emulsion side

down on registration posts. Place platen

on platen posts, foam side down, on top

of screen.

After emulsion has completely dried,

remove protective plastic sheet from

unexposed, emulsiﬁed screen.

Blot screen with lint-free towel. Place

screen in drying rack.

TIP: If plastic sheet does not remove

easily, the emulsion is not dry.

Press fan button.

It will take one drying cycle or more for

screen to dry. Touch screen with ﬁngers to

make sure it is dry. A hair dryer or fan may

be used for additional drying.

6. EXPOSING SCREEN:

7. WASH AND DRY SCREEN:

CREATE

8. PRINT SCREEN

Insert the ﬁrst screen onto top lid (make

sure screen ﬁts over registration posts,

front side up).

Before using platen, remove protective

sheet from platen adhesive sheet.

Apply generous bead of ink onto screen

just above design. Make sure bead of ink

is at least as wide as design.

Flood screen with ink by gently pulling

squeegee across design.

Mount t-shirt or other material on

platen. Open lid and place platen on

platen posts. Close lid.

TIP: Tape the back of the screen around

edges to seal any open screen areas.

TIP: Use Yudu Blockout (sold separately)

or small pieces of tape to ﬁll any holes,

scratches, and registration marks in emulsion.

TIP: When adhesive sheet is no longer

sticky, peel off and replace. (Adhesive

sheets sold separately. )

TIP: For large open areas of design,

you may ﬁnd it necessary to be more

generous with ink.

TIP: Hold lid up at a slight angle while

ﬂooding screen. Make sure material is not

touching the screen before you ﬂood image.

TIP: Material should be completely

adhered to platen with platen adhesive

sheets to keep material from shifting.

Otros manuales para Yudu

Tabla de contenidos

Otros manuales de Impresora de Provo Craft

Provo Craft

Provo Craft Yudu Instrucciones de montaje

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario