Proslogan IU-4009 Manual de usuario

PROFESSIONAL

WIRELESS MICROPHONE

----- 1/2/4/8 Channel Wireless System

User’s manual

----- 1/2/4/8 Channel Wireless System

~1~

Precautions

1. To assure the finest performance, please read this manual carefully. keep it in a safe place for future

reference.

2. Do not use force on switches or connection wires. When moving unit, first disconnect the powerplug

and the wires connected to other equipment. Never pull the wire itself.

3. Install this unit in a cool, dry, clean place--- away form window, heat sources of excessive vibration,

dust, moisture and cold. To prevent fire or electrical shock, do not expose this unit to rain or water.

4. Only use provided power adapter, and confirm the voltage is correct to the adapter, The use of

other power adapter may damage the machine and void your warranty.

5. The machine use 220VAC power supply voltage, the use of other voltage may cause fire and fault.

6. Avoid collisions or vibration of the machine.

7. Never open or try to change the circuit of the receiver, transmitters and the power adapter. This

could damage your machine and void your warranty. If the machine fails to work, please send to the

Maintenance Service Center authorized.

8. Be sure to read the"troubleshooting"section regarding common operating errors before concluding

that the unit is faulty.

9. If there are any abnormal cases happened during using, such as smoke,odor,etc.,please unplug the

adapter immediately,and send the machineto the Maintenance Service Center authorized asap.

10. Use the 2A alikline batteries or rechargeable batteries for the transmitter.Be sure the polarities are

correct.(See the illustration inside the battery compartment.)Remove the batteries if the

transmitters will not be used for an extended period of time.

11. When not planning to yse this machine for long periods of time,disconnect the power adapter plug

form the wall outlet.12.Do not attempt to clean the unit with chemical solvente;this might damage

the finish.Use a clean,dry cloth.

Contents Features

The front panel name and function

The rear panel name and function

Handheld Transmitter

Bodypack Transmitter

Six, the infrared frequency

Eight, open process equipment

Technical indicators

3-6

~2~

the menu operation method 8

Precautions 1

Contents Features 2

Conference Transmitter 8

~4~

1.The front panel name and function

12 3 35 4

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

CHANN EL. A

SET SET

CHANN EL. B

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

1, "POWER" power switch;

2, "IR" infrared synchronization window (with the transmitter relative to the

30CM frequency);

3, A/B channel display, real-time display of the working state;

4, A/B channel infrared frequency and function settings;

5, A/B channel selection key;

2.The rear panel name and function

1 2 3

4 5

BAL ANCED . B BAL ANCED . AMIX O UT

DC 12 ~15V

500 mA ANT . AANT . B VOL . B VOL . A

MIN MA X

WARNING :

TO REDUC E THE RIS K OF FIRE O R ELECT RIC

SHOCK D O NOT EXP OSE TNI S EQUIP MENT TO RA IN MOIS TURE

ATTENTIO N:

RISQU E DE CHOC E LECTR UQUE NE PAS O UVRIR

RISK OF E LECTR IC SHOC K

DO NOT OP EN

C A U T I O N

SERI AL:

FREQ UENCY:

PROF ESSIO NAL WIR ELESS S YSTEM

1, power adapter socket, connect DC/500mA 12V power input;

2, A/B channel antenna socket;

3, potentiometer, A/B channel volume control;

4, parallel output, A and B independent audio XLR parallel output.

5, non parallel output, A and B audio 6.35 mixed output;

~3~

1.The front panel name and function

SET

syn

POWER

UHF WIRE LES S MICR OPHON E RECEI VER

RF Ⅰ

AF Ⅱ

MUT E

FRE Q.

-30 - 25 -2 0 -15 -10 - 5 0 P EAK

12 3 5 4

1, "POWER" power switch;

2, "IR" infrared synchronization window (with the transmitter relative to the

30CM frequency);

3, A channel display, real-time display of the working state;

4, A channel infrared frequency and function settings;

5, A channel selection key;

2.The rear panel name and function

1, power adapter socket, connect DC/500mA 12V power input;

2, A/B channel antenna socket;

3, potentiometer, A/B channel volume control;

4, parallel output, A and B independent audio XLR parallel output.

5, non parallel output, A and B audio 6.35 mixed output;

12 3

5 4

BALANCED

MIX OUT DC 12V/800m A ANT . A

ANT . B

VOLUME

MIN M AX

ATTENT ION:

RIS QUE DE CHO C ELECT RUQUE N E PAS OUVR IR

RIS K OF ELEC TRIC SH OCK

DO NO T OPEN

C A U T I O N

FRE QUEN CY:

~5~

BALA NCED . AMIX OU T DC 12V /800m AANT . AA NT . B BALA NCED . BBALA NCED . CBALA NCED . D

VOL . C

MIN MA X

VOL . D

MIN MA X

VOL . A

MIN MA X

VOL . B

MIN MA X

4 45

SET

CHANN EL. A CHANNEL.B

SET

CHANN EL. C

SET SET

CHANN EL. D

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

12 3 35 4 4

33 5 445

3.The front panel name and function

4.The rear panel name and function

1, "POWER" power switch;

2, "IR" infrared synchronization window (with the transmitter relative to the

30CM frequency);

3, A/B/C/D channel display, real-time display of the working state;

4, A/B/C/D channel infrared frequency and function settings;

5, A/B/C/D channel selection key;

1, power adapter socket, connect DC/500mA 12V power input;

2, A/B channel antenna socket;

3, potentiometer, A/B/C/D channel volume control;

4, parallel output, A/B/C/D independent audio XLR parallel output.

5, non parallel output, A and B audio 6.35 mixed output;

~6~

BALA NCED . EMIX O UT DC 12 V/200 0mAANT . CA NT . D BALA NCED . FBA LANCE D . GBALA NCED . H

VOL . G

MIN MA X

VOL . H

MIN MA X

VOL .E

MIN MA X

VOL . F

MIN MA X

BALA NCED . AMIX OU T ANT . AA NT . B BALA NCED . BBALA NCED . CBALA NCED . D

VOL . C

MIN MA X

VOL . D

MIN MA X

VOL . A

MIN MA X

VOL . B

MIN MA X

4 45

CHANN EL. A

SET

CHANN EL. B

SET

CHANN EL. C

SET SET

CHANN EL. D

CHANN EL. E

SET

CHANN EL. F

SET

CHANN EL. G

SET SET

CHANN EL. H

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

12 3 3533 5 445

3 3 3 3

5 5 5 5

4 4 4 4

4 5 4

5.The front panel name and function

6.The rear panel name and function

1, "POWER" power switch;

2, "IR" infrared synchronization window (with the transmitter relative to the

30CM frequency);

3, A/B/C/D/E/F/G/H channel display, real-time display of the working state;

4, A/B/C/D/E/F/G/H channel infrared frequency and function settings;

5, A/B/C/D/E/F/G/H channel selection key;

1, power adapter socket, connect DC/500mA 12V power input;

2, A/B/C/D channel antenna socket;

3, potentiometer, A/B/C/D/E/F/G/H channel volume control;

4, parallel output, A/B/C/D/E/F/G/H independent audio XLR parallel output.

5, non parallel output, A and B audio 6.35 mixed output;

~8~

9.Conference transmitter

1, microphone head: pick up sound input;

2, liquid crystal display;

3, power switch;

4, infrared port, receive infrared beam, so that the

frequency synchronization;

5, battery warehouse, assembly 2 AA battery;

10.menu operation

(1), power on and off

1. Press the a power button, the receiver will begin energized and internal CPU initialization,

the system is restored to the when used on a working state.

2, in the boot state, press the power button, the system began to save the current settings,

and then automatically shut down power.

(2), frequency selection

1, according to about "▲" key or " "keys, frequency and channel menu will be flashing. This

could be a direct press" ▲ "key or " "key system Will increase or decrease the frequency

set by the original menu. If the long press "▲" key or" " button for 2 seconds, the

frequency will be quick step Or reduced.

(Note: Each channel operation method is the same)

2, choose a good frequency, press the "SET" button to send the infrared data to determine

the exit, such as no operation, the menu is flashing 5 confirmed exit.

▲

8.Bodypack Transmitter

7.Handheld Transmitter

~7~

1, Voice head module: pick up audio input;

2, IR window: IR infrared synchronous frequency window, Host frequency

synchronization data;

3, Display: display working status;

4, Power switch, long press the power switch;

5, Battery warehouse: the assembly of 2 AA batteries;

6, Transmit antenna;

IR UP ACT DO WN

1, power switch;

2, status indicator;

3, microphone input socket;

4, transmit antenna;

5, LCD display;

6, infrared frequency window;

7, battery warehouse (assembly

2 AA battery);

8, infrared ray key;

9, high and low emission power

conversion;

POWER P OWER

AA X 1.5v AA X 1. 5v

AA X 1.5v AA X 1.5v

~10~

13.Technical index

Wireless Receiver

In the frequency range

maximum deviation + 15KHz

In the letter exercise than >100dB

comprehensive distortion less than 0.02%

frequency stability + 0.03%

audio response + 40 Hz-16 KHz

dynamic range >100dB

rated working current 480 Ma

working temperature -20 to +50 DEG C

receiver voltage: DC 12 ~ 15V

rated working current 150 mA

AC - receiver voltage 100 ~ 240V

Effective working distance 100 meters

Wireless Transmitter

In the frequency range

maximum deviation + 15KHz

In the letter exercise than >100dB

comprehensive distortion less than 0.02%

frequency stability + 0.03%

audio response + 40 Hz-16 KHz

dynamic range >100dB

Power 8.5mW

working temperature -20 to +50 DEG C

battery time 10-12 hours

rated working current 150 mA

~9~

11.infrared automatic frequency

1, the receiver set good working frequency.

2, open the transmitter power, the infrared receiver window at the receiver of the infrared emission

window, press the "SET" button, the transmitter frequency The rate is automatically set to the

receiver frequency. (Note: all channels are identical).

1, the two antennas are respectively mounted on the back panel of the antenna connecting seat, and

the antenna is pulled to the position of the vertical line into a 45 degree angle.

2, the output of the DC power adapter is connected to the DC power input socket of the receiver, and

the other end is connected to the AC power outlet.(Note: the AC power source for the power

adapter must be in accordance with the specifications of the area.)

3, can not be connected to the parallel mixed output socket: at the same time, the output of the A

channel and B channel audio signal.

4, can be connected to the parallel output socket, A, B channel audio parallel output socket is

independent.

5, in order to make the machine to obtain a good reception, the receiver must be installed on the

ground to less than 1 meters from the ground, the transmitter and the receiving antenna

Less than 2 meters, more than 1 meters above the surface of the wall.

6, to keep the antenna away from the interference sources, such as computer equipment, digital

equipment, television, also want to stay away from large areas of metal objects.

7, the use of the receiver and transmitter between the use of the site as far as possible to reduce

obstacles between the line of sight for the best.)

12.the receiver installed

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

CHANN EL. A

SET SET

CHANN EL. B

RF Ⅰ

AF Ⅱ

MUTE

FREQ.

-30 -2 5 -20 -1 5 -10 -5 0 PEA K

AA X 1.5v AA X 1.5v

510.5MHz-585MHz UHF

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used

in portable exposure condition without restriction.

Tabla de contenidos

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Shure

Shure UA844 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario