PROPOINT 8676934 Manual de usuario
V1.2 8676934
Please read and understand all instructions before use. Retain this
manual for future reference.
USER MANUAL
84 IN. INDUSTRIAL CEILING FAN
8676934 84 IN. INDUSTRIAL CEILING FAN V1.2
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Size 84 in.(213.36 cm)
Downrod Length
9 in. (22.86 cm)
Downrod Diameter 3/4 in. (1.90 cm)
Construction
Aluminum Blades
Number of Speeds 6 Speed Reversible
Voltage Rating 120V
Wattage Rating 35W
INTRODUCTION
Includes a remote control, an optional light kit and two 13 watt
CFL bulbs. Suitable for indoor use.
SAFETY
WARNING! Read and understand all instructions before using
this tool. The operator must follow basic precautions to reduce
the risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this
manual. A notice is an alert that there is a possibility of property
damage, injury or death if certain instructions are not followed.
84 IN. INDUSTRIAL CEILING FAN
V1.2 84 IN. INDUSTRIAL CEILING FAN 8676934
Visit www.princessauto.com for more information 3
DANGER! This notice indicates an immediate and specific
hazard that will result in severe personal injury or death if the
proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe
practice that could result in severe personal injury or death if
the proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous
situation that may result in minor or moderate injury if proper
practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property damage, but not
personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area
clean, well-lit and free of distractions.
2. Keep anyone not wearing the appropriate safety
equipment away from the work area.
3. Store tools properly in a safe and dry location. Keep tools
out of the reach of children.
4. Do not install or use in the presence of flammable gases,
dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by
the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and
side protection for the eyes. Eye protection equipment
should comply with CSA Z94.3-07 or ANSI Z87.1 standards
based on the type of work performed.
8676934 84 IN. INDUSTRIAL CEILING FAN V1.2
4 For technical questions call 1-800-665-8685
2. Wear gloves that provide protection based on the work
materials or to reduce the effects of tool vibration.
3. Wear protective clothing designed for the work
environment and tool.
4. Non-skid footwear is recommended to maintain footing
and balance in the work environment.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work
environment to avoid personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence
of drugs, alcohol or medications.
2. Avoid wearing clothes or jewelry that can become
entangled with the moving parts of a tool. Keep long hair
covered or bound.
3. Do not overreach when operating the tool. Proper footing
and balance enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence to the
tool safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for
a specific function. Do not modify or alter this tool or use it
for an unintended purpose.
2. Ensure that the installation site is clear of obstructions and that
the rotating blades do not come in contact with any object.
Install the blades 10 ft (3 m) away from the floor.
3. Mount the fan on a ceiling joist if possible; the joist must be
able to support the weight of the moving fan. If mounting
on a ceiling outlet box, use a 4 x 2-1/8 in. deep, metal
octagon box that is UL-listed as suitable for fan use and
V1.2 84 IN. INDUSTRIAL CEILING FAN 8676934
Visit www.princessauto.com for more information 5
capable of supporting 35 lb (15.87 kg) or less. Use the
mounting hardware provided with the outlet box.
4. Only use UL/ETL listed light kits if installing kits that are
not provided with the fan. Refer to the kit's manual for
installation procedures. Disconnect the fan from the supply
circuit before installing the light kit to prevent
electric shock.
5. Protect the fan motor housing's finish by keeping the part
in the packaging until it is ready for installation.
6. Do not attach the fan blades before mounting the fan
motor housing. If installing more than one ceiling fan, do
not mix the blade sets.
7. Do not bend the blade brackets while installing or cleaning
the fan to prevent personal injury.
8. Do not use solid-state speed control devices with the fan to
prevent fire or electrical hazards and personal injury.
9. Ensure that all connections are secure once the fan is
mounted to prevent it from falling and causing damage
and/or personal injury.
10. The fan is pre-lubricated and ready for use after
installation. Further lubrication is not necessary.
11. Turn the fan off and allow the blades to fully stop before
reversing the fan direction.
ELECTRICAL SAFETY
WARNING! Do not touch or handle a live tool with any part of
your body that is wet or damp. Wet skin reduces resistance to
electrical current, increasing the danger of a serious or
fatal shock.
1. Protect yourself against electric shocks when working on
electrical equipment. Avoid body contact with grounded
surfaces. There is an increased chance of electrical shock if
your body is grounded.
8676934 84 IN. INDUSTRIAL CEILING FAN V1.2
6 For technical questions call 1-800-665-8685
2. Do not expose the tool to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
3. Do not alter any parts of the tool or accessories. All parts
and accessories are designed with built-in safety features
that may be compromised if altered.
4. Make certain the power source conforms to requirements
of your equipment (see Specifications).
5. When wiring an electrically driven device, follow all
electrical and safety codes, as well as the most recent
Canadian Electrical Code (CE) and Canadian Centre for
Occupational Health and Safety (CCOHS).
WARNING! All wiring should be performed by a
qualified electrician.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect
for damage. Make sure that all items in the parts list are included.
ASSEMBLY & INSTALLATION
Numbered references in parenthesis (#1) refer to the included
Parts List. Dashed numbers in parenthesis (Fig. 1-1) refer to a
specific point in an illustration or image.
HANGING THE SYSTEM
WARNING! Switch off the appropriate circuit breakers at the
electrical panel before starting to avoid electrical shock.
WARNING! Use an outlet box that can support up to 35 lb
(15.87 kg) to prevent the fan from falling and causing damage
and/or personal injury
V1.2 84 IN. INDUSTRIAL CEILING FAN 8676934
Visit www.princessauto.com for more information 7
1. Attach the
mounting
bracket (#1) to the
outlet box (not
included) using the
appropriate
hardware.
See Fig. 1.
2. Remove the cross
pin (Fig. 2-1) and
cotter pin (Fig. 2-2)
from the
downrod (Fig. 2-3).
3. Loosen the two downrod jam
screws (Fig. 3-1). Ensure that
the hex nut (Fig. 3-2) is on the
side of the set screw head.
4. Insert the yoke cover (Fig. 4-1),
deco ring and canopy (Fig. 4-2)
onto the downrod.
Fig. 4
Fig. 5
Fig. 6
Fig. 3
Fig. 1
Fig. 2
8676934 84 IN. INDUSTRIAL CEILING FAN V1.2
8 For technical questions call 1-800-665-8685
5. Feed the motor lead wires (Fig. 5-1) through the downrod.
Insert the downrod assembly into the yoke (Fig. 5-2). Insert
the cross pin (Fig. 5-3) from Step 2 through the yoke and
downrod. Secure with the cotter pin (Fig. 5-4) from Step 2.
6. Tighten the two downrod jam screws
(Fig. 6-1). Secure by using a wrench to
tighten the hex nut (Fig. 6-2). Pull down
the yoke cover (Fig. 6-3) to cover
the yoke.
7. Lift the fan assembly (#5) onto the
mounting bracket. See Fig. 7.
8. Rotate the fan until the ball groove (Fig.
8-1) engages the ridge (Fig. 8-2) in the
mounting bracket.
CONNECTING THE WIRES
1. Assemble the wood screw (#14), spring washer (#12), flat
washer (#11) and safety cable as shown in Fig. 7-1. Secure
the wood screw to the ceiling joist through any available
slot on the mounting bracket. Tighten the safety cable.
2. Connect the electrical wires by following the diagram
below. Ensure that all exposed wires are secured inside wire
connectors or a terminal block.
Fig. 7
Fig. 8
V1.2 84 IN. INDUSTRIAL CEILING FAN 8676934
Visit www.princessauto.com for more information 9
2.1 Connect the white wire from the house to the white
wire from the fan.
2.2 Connect the black wire from the house to the black
wire from the fan.
2.3 Connect the ground wire from the house to the green
wires from the downrod and the mounting bracket.
2.4 Secure the ends together using the provided twist-on
wire connectors (#18).
2.5 Push the wires gently into the junction box with the
wire connectors pointing upwards.
INSTALLING THE
CANOPY
1. Push the canopy up until the two
screws (pre-screwed on the
mounting bracket) are engaged with
the two keyholes (Fig. 9-1) on
the canopy.
2. Rotate the canopy slightly until the
screw heads are engaged in the
narrow end of the keyholes.
3. Tighten both screws.
Fig. 9
8676934 84 IN. INDUSTRIAL CEILING FAN V1.2
10 For technical questions call 1-800-665-8685
INSTALLING THE BLADES
Attach the blades (#6) to the fan assembly (#5) using the flat
washers (#11) and the blade screws (#15).
INSTALLING THE LIGHT KIT
Fig. 11
Fig. 12
Fig. 13
1. Install the bulbs (#7) to the medium base sockets (Fig. 11-1).
2. Attach the glass shade (#8) by screwing it onto the light kit
pan clockwise. See Fig. 12.
IMPORTANT! If you are not installing the provided light kit,
attach the bottom plate (#9) instead of the glass shade to the
pan. See Fig. 13.
Fig. 10
Tabla de contenidos
Idiomas:
Otros manuales de Admirador de PROPOINT
