Proluxe TACO BELL Vantage SL Compact Manual de usuario
Operations Manual
Vantage SL Compact - Compact Split Lid Grill
Model #: SL1266TB
WWW.PROLUXE.COM
Version: 022822
Congratulations on your selection of
the Vantage SL Compact Split Lid
Grill. Proluxe is a leading
manufacturer of food preparation
and cooking equipment designed for
the most demanding commercial
kitchens. Proluxe equipment is a
result of the highest quality
engineering and time-tested design.
This manual includes installation,
operation, and maintenance
procedures for your new split lid
grill. Please read this manual
carefully and keep it with your
machine for proper operation and
lasting service.
G E T T I N G S T A R T E D
Please read carefully before attempting to
use this appliance.
1. Place in location where it will be used
allowing for clearances per the
dimensions indicated. Allow 2”
minimum clearance between
adjacent equipment and/or wall
areas.
2. Plug into proper 3 prong wall outlet.
If other appliances are connected to
the same circuit make sure the total
load does not exceed a maximum
ampacity of the circuit. Electrical
information is as follows:
Electrical:
●Voltage: 120/230
●Amps: 15.83/8.3
●Hertz: 50/60
●Watts: 1900/1900
PLUG
●120V: 72” cord and NEMA 6-20P
approved plug.
●230V: 72” cord and plug per country
requirements.
3. Press the power button, the green
light above will illuminate when
powered on.The display flashes and
shows left preset timer during
warm-up. Pre-heat time will be 40-50
minutes. When the set point is
reached, the display stops flashing
and beeps 3 times.
4. Simply place product on either side of
the grill, close lid and press the
desired pre-set time cycle 10 or 20
seconds. After the time cycle is
finished press it again to reset the
time cycle.
1
I N T E R N A T I O N A L S Y M B O L S
Power Off
Power On
Hot Surface
Risk of Electrical Shock
Protective Earth Terminal
Caution - Warning
S A F E T Y S U M M A R Y
Warning
To reduce the risk of electrical shock, do not
remove or open cover. No user-serviceable
parts inside. Refer servicing to qualified
personnel.
In case of power cord damage, do not
attempt to repair or replace the power cord.
Please contact the manufacturer or the local
distributor.
Warning
For continued protection against fire and
electric shock, replace with the same type
and rating fuse. Listed Supplemental Fuse
rated max 3A, 120Vac.
Caution Hot
Avoid touching hot surfaces while operating
the machine.
Caution
When servicing or cleaning the machine,
make sure that the power cord is removed
from the wall socket.
During normal operation, the base of the
machine must be installed or placed above
the wall socket.
2
T E M P E R A T U R E/T I M E R
S E T T I N G S
How to Find Set Temperature
To find the temperature of upper platens:
Press and hold the TEMP button and the
arrow up (↑) button at the same time.
To find the temperature of bottom platens:
Press and hold the TEMP button and the
arrow down (↓) button at the same time.
Adjusting the Set Temperature
1. Press and hold the TEMP button and
the arrow up (↑) button at the same
time for 15 seconds.
2. The current temperature with display
on the right digital display screen
only.
3. Using the up (↑) and down (↓) adjust
the temperature to your desired
setting.
4. Once your desired temperature is set,
push the TEMP button to return.
Adjusting the Set Time
1. Press the TEMP button first and then
select the desired timer button and
hold for 5 seconds.
2. The current temperature with display
on the right digital display screen
only.
3. Using the up (↑) and down (↓) adjust
the timer to your desired setting.
4. Once your desired temperature is set,
push the TEMP button to return.
Note: When adjusting the timer settings, the
right set of buttons control the left side. Your
left side timer will automatically set to your
right control settings. If you desire a separate
left timer you can manually adjust the left
side timer without affecting the right timer.
3
C L E A N C Y C L E
Start Cycle
To start a clean cycle, push CLEAN button
once so the CLEAN LED light is turned on. All
preset LED’s are turned off, and the
temperature set point is changed to the clean
set point of 275°F. This also initiates the cool
down to clean set point condition as well the
display starts flashing until the clean set
point is reached.
Stop Cycle
To stop the clean cycle, simply press the
CLEAN button once to deactivate the clean
cycle. The CLEAN LED is turned off, the
preset LED’s are restored, the temperature
set point is changed to the main set point.
Again, the warm-up condition is initiated and
the display flashes until the cook set point is
reached.
Change Clean Temp
275°F is the factory default temp for the
CLEAN cycle. To change the CLEAN cycle
temp, simultaneously hold down the TEMP
and CLEAN buttons for 15 seconds. The
current temp setting will display on the right
digital display only. Using the up or down
arrows to adjust to the desired temp.
P R E V E N T A T I V E
M A I N T E N A N C E
Proluxe machines are relatively maintenance
free. For a long lifespan, the following
preventative maintenance should be
followed:
Daily Care:
1. Platens: Turn your machine off and allow
to cool down before attempting to clean.
These platens should only be cleaned with
mild soap and warm water then wiped off
with a clean, soft cloth or soft sponge.
2. Exterior surfaces: Wipe daily with mild
soap and warm water.
DO NOT use ice or cold water to cool the
unit down. This can cause platens to warp.
Service Problems:
Contact our factory at (800) 624-6717 (U.S.
only) or approved service agency. When
contacting the factory for information, parts
or service instructions, please provide the
serial number of the machine be provided.
This number can be found on the serial plate
located on the rear of the machine.
4
Vantage SL Compact Troubleshoot Guide - Model #: SL1266TB
Problem
Cause
Action
Ref #
Power Button on
Digital Controller
face is depressed but
doesn’t turn on.
1. Power cord is not plugged in.
2. Circuit breaker is tripped off in the
site's breaker box.
3. Transformer has taken an
electrical surge and is damaged.
4. Check voltage on the secondary
side of the Transformer. If you read
12VDC then you are receiving
voltage to the controller.
5. Possible blown fuse.
1. Plug the power cord into wall
receptacle and power button.
2. Reset circuit breaker that the
grill is plugged into. Depress
Power Button to turn on.
3. Replace Transformer after you
check secondary side of
transformer. If working properly,
you should receive 12vdc.
4. Replace controller. Controller
should be on once the power
button is depressed.
5. Replace fuse.
77
-----
39
31
32
Digital Controller's
LED's are scrambled
or randomly erratic.
If when turning on,
the display will first
go to segment check
1. Possibly a component on the
Digital controller is damaged.
2. Control needs to reset.
1. Replace digital controller.
2. While unit is on unplug unit,
wait for 1 min. Then plug machine
on again and depress the power
button.
-----
31
Digital Controller on
startup goes through
LED segment check
(8888) then to
version # and then
loops back to to the
above reboot.
The relay driver on the digital control
may be blown.
Replace digital controller.
31
Digital display shows
PROB. No heat on
any platen.
Sensor lost it's continuity as shown
on a muti-meter.
Disconnect prob that is open (no
continuity as shown on a multi-
meter. Must replace sensor
(RTD). Do not cut and splice new
sensor. Install new 2000 ohm
RTD sensor to under side of heat
platen and reconnect to the
controller.
37,
38
5
When depressing the
tactile button on
digital controller,
nothing happens.
The tactile buttons under the overlay
may be not close enough to activate.
Same goes if the buttons are already
pressed by overlay without
depressing button.
Carefully (no too much at one
time to avoid fracturing the
traces on the controller) tighten
the nuts on the back of the
controller until button activate.
Same goes in reverse if buttons
are held down by the overlay.
Digital display shows
relay and particular
zone is overheating.
Beeper not
functioning or
intermittent beeper
sound.
1. The relay on the switched side is
not opening to regulate temperature.
2. Beeper on digital control board
failed.
1. Replace the relay.
2. Replace digital controller board
27
31
If setpoint is reached
but slightly off in
temperature.
Offset may need to be calibrated and
adjusted.
Call (800) 624-6717 ext. 129 for
instructions.
Heater platen
overheating
If the relay (depending on the year of
the model) on the coil side are
receiving 12vdc indicates the
controller is functioning properly. On
the switching side of the relay, is
there 120 vac going to the heater in
question. If there is no voltage on
the to the switching side of the relay
to the heaters, the relay is not
working properly.
Replace relay If the controller's
heat-on LED is not lit indicating
the controller is working
properly.
27
6
7
8
9
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Parrilla de Proluxe
Proluxe
Proluxe Progrill CS1500 Manual de usuario
Proluxe
Proluxe TW2540 Manual de usuario
Proluxe
Proluxe SL1577 Manual de usuario
Proluxe
Proluxe Vantage CS CSD1515PEE Manual de usuario
Proluxe
Proluxe SL1577HDA Manual de usuario
Proluxe
Proluxe SL1577PHC Manual de usuario
Proluxe
Proluxe Vantage SL SL1577 Manual de usuario
Proluxe
Proluxe Progrill SL1577K Manual de usuario
Proluxe
Proluxe DEL TACO SL1266DTA Manual de usuario
Proluxe
Proluxe Progrill SL1577PHN Manual de usuario
Proluxe
Proluxe Vantage SL Manual de usuario
Proluxe
Proluxe Vantage SL Compact SL1266 Manual de usuario
Proluxe
Proluxe TACO BELL PROGRILL SL1577TBCEC Manual de usuario
Proluxe
Proluxe CSD1515 Manual de usuario
Proluxe
Proluxe Vantage CS Compact CSD1212E Manual de usuario
Proluxe
Proluxe Edge SE Manual de usuario
Proluxe
Proluxe TACO BELL PROGRILL SL1577Y Manual de usuario
Proluxe
Proluxe Progrill CS157PHNA Manual de usuario
Proluxe
Proluxe CSD1212 Manual de usuario
Proluxe
Proluxe Tortillapro Pancheros DP2000BPP Manual de usuario
