Prolitec AirQ AQ570 Manual de usuario
Through Wall
installation instructions
PERFECTLY SCENTED ENVIRONMENTS
Original Instructions
Rev. 2019-01-04
Through Wall Kit 4Unpacking
Unpacking
Remove all parts from the container. The following items should be included:
1. AQ570/580 Appliance (not pictured)
2. 110/220V to 15V Power Adapter (not
pictured)
3. Universal Plug Kit (not pictured)
4. Wall Mount Hardware Kit (not pictured)
5. Through Wall Fitting Parts (in bag)
a. Base Housing
b. Trim Ring
c. Drywall Clips (2)
d. 1 ¼” Screws (2)
e. 3” Screws (2) (not pictured)
f. Fan w/ 18” black and red wires
g. Tube Connector
h. Wire Connectors (2)
6. Tubing (18”)
7. Braided Cord Wrap (18”)
5a
5b
5c
5d
5f
5g
5h
7
6
2
Through Wall Kit 5Assembly
Assembly
1. Press t the fan into the base housing part by aligning the three corner holes to the three
hexagonal posts.
2. Insert the correct length screw (dependent on installation type) into the holes on the front of
the base housing part, thread the drywall clips onto each screw, and tighten screws three or four
turns.
a. 1 ¼” screws should be used on drywall/gypsum board
b. 3” screws should be used on doors
3
Through Wall Kit 7Installation
Installation
Positioning the appliance in the “appliance mounting room”
1. Identify the area on the opposite side of the wall from the approximate mounting location.
2. Verify that you have an area of empty wall cavity, using a stud nder.
3. Cut a 6” x 6” square hole with a keyhole saw, so that you can verify that there is not electrical or
plumbing in the way and so that you can get the drill inside the wall cavity.
4. Working from within the 6” square, drill a pilot hole through the front wall surface, with the ½”
drill bit.
5. Mount the appliance on the wall normally, with the top of the appliance six to eight inches below
the bottom of the 6” square hole.
4
Through Wall Kit 8Installation
Positioning the plume outlet in the room to be scented
1. Drill a 2 1/8” hole, centered on the pilot hole, with the hole saw.
2. Insert the base housing, with the fan, clips, and tube already attached, into the hole.
3. Screw in the two screws until you feel the plastic snug towards the drywall.
4
Through Wall Kit 10Installation
Connecting the appliance in the “appliance mounting room”
1. Connect the wires of the fan assembly to the wires from the appliance, red to red and black to bl
2. Bundle the wires and tube inside of the sleeve.
3. Install the cartridge with the top plume port open.
4. Insert the plume tube into the top plume port of the cartridge.
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios de Prolitec
Prolitec
Prolitec AIRQ AQ 570 CM Manual de usuario
Prolitec
Prolitec AirQ AQ1200 Manual de usuario
Prolitec
Prolitec AirQ AQ 1270 TT Manual de usuario
Prolitec
Prolitec AirQ AQ150 Manual de usuario
Prolitec
Prolitec AIRQ AQ880 Manual de usuario
Prolitec
Prolitec AQ1570 Manual de usuario
Prolitec
Prolitec AirQ 270 TT Manual de usuario
Prolitec
Prolitec AirQ AQ550 Manual de usuario
Prolitec
Prolitec AirQ 1280 Manual de usuario
Prolitec
Prolitec GENIE Manual de usuario
