ProLights EclPanel TWCJR Manual de usuario

USER MANUAL

REV.02-11/20 English version

EclPanel TWCJR

370W Tunable White and colourful LED

soft light with pixels and lighting effects

Thank you for choosing PROLIGHTS.

Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance require-

ments for professionals and designed and manufactured for the use and application as shown in this document.

Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be

a source of danger.

This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respec-

tively applicable national accident prevention rules and regulations.

Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated

companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any

other loss occasioned by the use of, inability to use or reliance on the information contained in this document.

Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial

PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).

Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad

set of always updated technical documentation: specications, user manual, technical drawings, photometrics,

personalities, xture rmware updates.

The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS

services or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and sub-

sidiaries.

136,200; Itri 04020, Italy.

1PROLIGHTS - Ecl PanelTWCJR

INDEX

SAFETY INFORMATION 2

1 - PACKAGING 5

PACKAGE CONTENT....................................................................................................... 5

OPTIONAL ACCESSORIES............................................................................................... 5

2 - TECHNICAL DRAWING 6

3 - INSTALLATION 7

MOUNTING...................................................................................................................... 7

4 - CONNECTION TO THE MAINS SUPPLY 8

5 - START UP 8

CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................... 8

6 - PRODUCT OVERVIEW 9

7 - DMX CONNECTION 10

CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 10

INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 10

CONNECTION DAISY CHAIN........................................................................................ 10

CONNECTION OF THE DMX LINE................................................................................ 10

CONSTRUCTION OF THE DMX TERMINATION ........................................................... 11

DMX ADDRESSING ........................................................................................................ 11

OPERATION AS A WIRELESS TRANSMITTER................................................................ 12

DMX TO WDMX (TX)...................................................................................................... 12

OPERATION AS A WIRELESS RECEIVER........................................................................ 12

WDMX TO DMX (RX)...................................................................................................... 12

8 - CONTROL PANEL 13

DISPLAY AND BUTTONS LAYOUT................................................................................. 13

ROTATORY KNOB LAYOUT ........................................................................................... 13

9 - MENU STRUCTURE 14

10 - RDM FUNCTIONS 18

11 - DMX CHARTS 19

12 - ACCESSORIES INSTALLATION 26

THE POLE OPERATED YOKE (code ECLPANELJRPOYO).............................................. 26

RIGID EGG CRATES (codes EPTWCJREC4C, EPTWCJREC30, EPTWCJREC60) ........... 27

DIFFUSION FILTERS (codes EPTWCFILTERHD, EPTWCFILTERMD, EPTWCFILTERLD) . 28

BARN DOOR (code EPTWCJRBD) ................................................................................. 29

13 - MAINTENANCE 30

MAINTENANCE AND CLEANING THE PRODUCT........................................................ 30

REPLACING THE FUSE................................................................................................... 30

VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 30

TROUBLESHOOTING..................................................................................................... 31

PROLIGHTS - Ecl PanelTWCJR2

SAFETY INFORMATION

WARNING!

• Please read carefully the instruction reported in this section before installing, power-

ing, operating or servicing the product and observe the indications also for its future

handling.

This unit is not for household use, only professional applications.

Installation

• This product is designed for indoor and dry environments.

• Do not use in wet location and do not expose the xture to rain or moisture.

• Never use the xture in places subject to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Excessive dust, smoke uid, and particle build up degrades performance, causes

overheating and will damage the xture. Damage caused by inadequate cleaning or

maintenance is not covered by the product warranty.

0,5 m Minimum distance of illuminated objects

• The projector needs to be positioned so that the objects hit by the beam of light are

at least 0.5 meters (1.64 ft) from the lens of the projector.

45°

aMax operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).

-20°

Minimum operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).

Protection from burns and fire

• The exterior of the xture becomes hot during use. Avoid contact by persons and

materials.

• Ensure that there is free and unobstructed airow around the xture.

• Keep ammable materials well away from the xture

• Do not expose the front glass to sunlight or any other strong light source from any an-

gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.

• Do not attempt to bypass thermostatic switches or fuses.

Indoor use

• This product is designed for indoor and dry environments.

• Do not use in wet location and do not expose the xture to rain or moisture.

• Never use the xture in places subject to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Excessive dust, smoke uid, and particle build up degrades performance, causes

overheating and will damage the xture. Damage caused by inadequate cleaning or

maintenance is not covered by the product warranty.

50°

Temperature of the external surface

• The surface of the xture can reach up to 50 °C (122 °F) during operation. Avoid

contact with people and materials.

3PROLIGHTS - Ecl PanelTWCJR

Minimun

distance

Risk

Group 2

Risk

Group 1

0.2 m

0.7 ft

14 m

47.93 ft

Protection and Warning against electrical shock

• Do not remove any cover from the product and disconnect the product from AC

power before servicing.

• Ensure that the xture is electrically connected to ground (earth). And use only a

source of AC power that complies with local building and electrical codes and has

both overload and ground-fault (earth-fault) protection.

• Before using the xture, check that all power distribution equipment and cables are

in perfect condition and rated for the current requirements of all connected devices.

• Isolate the xture from power immediately if the power plug or any seal, cover, cable,

or other component is damaged, defective, deformed or showing signs of overheat-

ing. Do not reapply power until repairs have been completed.

• Refer any service operation not described in this manual to PROLIGHTS Service team

or an authorized PROLIGHTS service center.

Connection to mains supply

• The Connection to the mains supply must be carried out by a qualied electrical

installer.

• Use only AC supplies 100-240V 50-60Hz, the xture must be electrically connected

to ground (earth).

• Select the cable cross section in according with the maximum current draw of the

product and the possible number of products connected at the same power line.

• The AC mains power distribution circuit must be equipped with magnetic+residual

current circuit breaker protection.

• Do not connect it to a dimmer system; doing so may damage the product.

70°

Temperature of the external surface

• The surface of the xture can reach up to 70 °C (159.8 °F) during operation. Avoid

contact with people and materials.

Maintenance

• Warning! Disconnect the xture from AC mains power and allow to cool for at least

10 minutes before handling.

• Only technicians who are authorized by PROLIGHTS or Authorised service partners

are permitted to open the xture.

• Users may carry out external cleaning, following the warnings and instructions pro-

vided, but any service operation not described in this manual must be referred to a

qualied service technician.

• Important! Excessive dust, smoke uid, and particle build up degrades performance,

causes overheating and will damage the xture. Damages caused by inadequate

cleaning or maintenance is not covered by the product warranty.

Photobiological safety

• This device emits potentially dangerous optical radiation and is identied in the cat-

egory of Risk Group 2 according to EN 62471.

PROLIGHTS - Ecl PanelTWCJR4

Do not stare at the operating light source

• Do not look directly at the LED source during operation. It can be harmful to the eyes

and skin.

• During Installation, operation and maintenance, be prepared for the xture to light

and move suddenly when connected to power.

• The device should be positioned so that prolonged staring into the luminaire at a

distance closer than 14 m is not expected.

Disposal

• This product is supplied in compliance with European Directive 2012/19/EU - Waste

Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-

pose/recycle this product at the end of its life according to the local regulation.

• The product contains a lithium ion battery.

• Don't throw the unit into the garbage at the end of its lifetime.

• Make sure to dispose is according to your local ordinances and/or regulations, to

avoid polluting the environment!

• The packaging is recyclable and can be disposed.

The products to which this manual refers comply with the European Directives pur-

suant to:

• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).

• 2014/30/EU - Electromagnetic Compatibility (EMC).

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).

• 2014/53/EU - Radio Equipment Directive (RED).

5PROLIGHTS - Ecl PanelTWCJR

1 - PACKAGING

PACKAGE CONTENT

• 1x ECLPANELTWCJR;

• 1x 1,5 meters power cable (SCHUKO plug - NEUTRIK POWERCON TRUE1 IP65);

• EPTWCJRFILTERMD: Front medium diffusion lter for ECLPANELTWCJR;

• ECLFRSPG: Spigot for PROLIGHTS Fresnel series;

• User manual.

OPTIONAL ACCESSORIES

• FCLPANELJR1U: Flight case for 1 pc of ECLPANELTWCJR.

• FCLPANELJR4U: Flight case for 4 pcs of ECLPANELTWCJR.

• ECLPANELJRPOYO: Pole operated aluminium yoke bracket for ECLPANELTWCJR.

• EPTWCJRFILTERINT: Front diffuser lter for ECLPANELTWCJR;

• EPTWCJRFILTERHD: Front high diffusion lter (less output) for ECLPANELTWCJR;

• EPTWCJRFILTERLD: Front low diffusion lter (more output) for ECLPANELTWCJR;

• EPTWCJREC30: 30 degree egg crate for ECLPANELTWCJR;

• EPTWCJREC60: 60 degree egg crate for ECLPANELTWCJR;

• EPTWCJREC4C: 4 chamber egg crate for ECLPANELTWCJR;

• EPTWCJRBD: Barn door with 4 directional aps to adjust the light beam;

• EPTWCJRSB11: SnapBag 1x1 for ECLPANELTWCJR by DoP choice;

• EPTWCJRSG4SB1: 40° SnapGrid for SnapBag, 1x1 for ECLPANELTWCJR by DoP choice;

• EPTWCJRSG4SB1140: 40° SnapGrid for SnapBag, 1x1 for ECLPANELTWCJR by DoP choice;

• EPSREM: Rabbit-Ears 1x1 MINI for ECLPANELTWCJR by DoP choice;

• EPSBRL3: Snapbag Lantern 3' for Rabbit-Ears by DoP. Incl. Lantern, Backcovers, Carry Bag;

• EPSBRL3C4: Cover for Snapbag Lantern 3' (EPSBRL3) by DoP choice; 4 sides, adj. with zipper;

• EPSBRM: SnapBag Medium to be mounted on Rabbit Ears by DoP;

• EPSGCM40: 40° SnapGrid, to be mounted on Snap Bag Medium (EPSBRM);

• EPSBRO3: Snapbag Octa 3' to be mounted on Rabbit-Ears by DoP;

• EPSGC3W40: 40° SnapGrid, to be mounted on Snap Bag Octa 3' (EPSBRO3);

• EPSBRO5: Snapbag Octa 5' to be mounted on Rabbit-Ears by DoP;

• EPSGC5W40: 40° SnapGrid, to be mounted on Snap Bag Octa 5' (EPSBRO5);

• EPSBRO7: Snapbag Octa 7' to be mounted on Rabbit-Ears by DoP.;

• EPSGC7W40: 40° SnapGrid, to be mounted on Snap Bag Octa 7' (EPSBRO7);

• SWIT500W2KIT: 24/48V 500W battery (>1.2hrs) KIT including 2*PBH260S smart power batt.+st.

adapt;

• UPBOX1U: Firmware uploader kit, USB IN, 3p XLR DMX OUT;

• RSR: Steel security cable for hanging bodies, inox steel shackle;

• C6040: Heavy-load aluminum clamp, 500kg loa, 48-51mm tubes, M10 bolt inc.

PROLIGHTS - Ecl PanelTWCJR6

2 - TECHNICAL DRAWING

Dimensions are in mm / in - Fig.1

Weight: 10.5 kg - 23.15 lbs

Weight: 11.8kg - 26.01 lbs

7PROLIGHTS - Ecl PanelTWCJR

Fig.2

3 - INSTALLATION

MOUNTING

Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,

auxiliary equipment, etc. and complies with locally applicable regulations.

When suspending the xture above ground level, secure it against failure of primary attachments by

attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor

point on the product main frame.

Do not use removable parts or weak anchors for secondary attachment.

Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-

pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.

Clamp

Ø11 mm [Ø0.4 in]

PROLIGHTS - Ecl PanelTWCJR8

5 - START UP

CONNECT AND DISCONNECT POWER FROM THE PRODUCT

To apply and disconnect power to the product:

• Check that the product is installed and secured as indicated in the Safety Informations, and that

personal safety will not be put at risk when the xture lights up.

• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).

• The product is then ready for its operations and can be controlled through the available input sig-

nals on board.

• To disconnect power from the product, disconnect the Mains from the socket.

• In case you wish to run the product through an external battery, then connect the product to an

external battery (24-36V) into the dedicated XLR4p socket; to disconnect power, disconnect the

Battery from the socket.

4 - CONNECTION TO THE MAINS SUPPLY

WARNING: For protection from electric shock, the xture must be earthed!

The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz

AC power source from 100-240 Volts.

If you need to install a power plug on the power cable to allow connection to power outlets, install a

grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts

about proper installation, consult a qualied electrician.

T max power consumption is 230W.

Core (EU) Core (US) Connection Plug terminal marking

Brown Black Live L

Blue White Neutral N

Yellow+green Green Earth

Tabla de contenidos

Otros manuales de Equipo de iluminación de ProLights

ProLights

ProLights Jet PAR7ZIP Manual de usuario

ProLights

ProLights LUMIPIX Manual de usuario

ProLights

ProLights ECLJZIPLZ1530 Manual de usuario

ProLights

ProLights ArcPod 15VW Manual de usuario

ProLights

ProLights LUMIPAR18QTOUR Manual de usuario

ProLights

ProLights Lumipix9HE Manual de usuario

ProLights

ProLights DIAMOND19WH Manual de usuario

ProLights

ProLights EclMiniProfile WDMX Manual de usuario

ProLights

ProLights Diamond142L Manual de usuario

ProLights

ProLights Z390LED Manual de usuario

ProLights

ProLights Stark Bar1000 Manual de usuario

ProLights

ProLights BB5PIX Manual de usuario

ProLights

ProLights Astra Profile400 Manual de usuario

ProLights

ProLights EVO128CYC Manual de usuario

ProLights

ProLights ECLIPSEJZIP Manual de usuario

ProLights

ProLights Cromowash300 Manual de usuario

ProLights

ProLights LEDFLOWERKIT4 Manual de usuario

ProLights

ProLights ArcPod 27VW Manual de usuario

ProLights

ProLights LUMIPIX8H Manual de usuario

ProLights

ProLights ARCLED2033 Manual de usuario

ProLights

ProLights EXPLO3000D Manual de usuario

ProLights

ProLights CUBER128 Manual de usuario

ProLights

ProLights CROMOSPOT250 Manual de usuario

ProLights

ProLights StudioCob PFC2 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario