ProLights PANORAMAIPSPOT Manual de usuario
USER MANUAL
MANUALE UTENTE
PANORAMAIPSPOT
HYBRID MOVING
EN - IT
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
REV. 01-09/18
1
PANORAMAIPSPOT
Packing content • PANORAMAIPSPOT
• Mount bracket
• Power supply cable and signal cable
• Safety rope
• User manual
TABLE OF CONTENTS Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description
1. 2 Technical specications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 Connect
DMX address
DMX Mode
Wireless
Artnet
RDM
3. 5 DMX Addressing
3. 6 Connection of the DMX line
3. 7 Construction of the DMX termination
3. 8 DMX Channel
3. 9 Gobos
3. 10 Setup
3. 11 Advanced
3. 12 Information
3. 13 Automatic Mode
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Trouble shooting
2
2
3
3
6
7
8
8
9
11
11
11
11
11
12
12
13
13
14
22
23
24
25
26
29
30
PANORAMAIPSPOT
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualied electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the xture under the following conditions:
- in places subject to vibrations or bumps;
- in places with an ambient temperature of over 45°C.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Do not dismantle or modify the xture.
• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation denitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way dierent to the one described in this manual, it may suer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.
• Always additionally secure the projector with the safety rope.When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the xture’s being used.
• For inside use only. Not designed for outside use.
• The minimum distance between the xture and surrounding walls must be more than 50 cm and the
air vents at the housing must not be covered in any case.
• Install the xture in a well ventilated place.
• Keep any inammable material at a safe distance from the xture.
• The maximum temperature that can be reached on the external surface of the tting, in a thermally
steady state, is high. After power o, please cool down over 15 minutes.
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their eectiveness is impaired.
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
3
PANORAMAIPSPOT
- 1 - INTRODUCTION
1.1 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
• Source: 420W high-power white LED
• CT: 7000K
• Lux: (5°) 21362lux @5m
• Lux: (50°) 1173lux @5m full
• Source life expectancy: >20.000 h
OPTICS
• Zoom: 5-50° motorised linear zoom
• Lens diameter: 120mm
• Lens type: HD anti-reection lenses with achromatic coating
• Focus: motorised with auto-focus
COLOUR SYSTEM
• Colour mixing: linear CMY
• CTC: linear CTO correction 2700~6000K
• Colour wheel: 8 dichroic lters + open
DYNAMIC EFFECTS
• Rotating gobos: 7 rotating gobos + open, interchangeable, indexing
• Gobo size: gobo Ø 27 mm - img Ø 21 mm - 1.1 mm
• Fixed gobos: 6 xed gobos + open, interchangeable
• Gobo size: gobo Ø 27 mm - img vØ 21 mm - 1.1 mm
• Circular prism: 3f with bi-directional rotation, indexing
• Frost: linear 0-100% frost lter
• Iris: 5-100% motorised linear iris
BODY
• Pan angle: 540-630°
• Tilt angle: 233°
• Pan/Tilt resolution: bit 8/16 bit
• Feedback: automatic repositioning after accidental movement
• Body: aluminium structure with hi-resistance polycarbonate cover
• Body colour: black
CONTROL
• Protocols: DMX512, RDM, Art-Net,W-DMX
• DMX channels: 19/21/28/29/36channel
• W-DMX: included, wireless solution receiver
• RDM: RDM ready for xture remote monitor and settings
• Display: LCD high resolution colour display
• Firmware upgrade: yes, via USB-DMX interface (UPBOX2) not included
• Hibernation: power safe mode when lost DMX
ELECTRONICS
• Dimmer: linear 0~100% electronic dimmer
PANORAMAIPSPOT
4
• Strobe / shutter: 1/28 Hz, electronic
• Battery backup: battery backup for user operation without connecting to the main power
• Operating temperature: -20° ~ +45°
ELECTRICAL
• Power supply: 100-240V – 50/60Hz
• Power consumption (at 230V): 492W
• Power consumption (at 120V): 501W
PHYSICAL
• Cooling: combination of heat pipe cooling system and low noise fan
• Sospension and xing: any position with quick-lock omega brackets
• Pan / tilt lock: pan / tilt locking for transportation and maintenance
• Signal connection: Amphenol XLR 5p IN/OUT connectors
• Data connection: RJ45 IN/OUT
• Power connection: Seetronic powerKon waterproof IN/OUT connectors
• IP rating: 65 for temporary outdoor application, not for xed installation
• Dimensions (WxHxD): 740x420x474mm
• Weight: 38kg
474,4
420 312
740,2
5
PANORAMAIPSPOT
Fig.1
Technical drawing
1
2
3
5
6
4
8 7
109
11 12
A
B
PANORAMAIPSPOT
6
1.2 OPERATING ELEMENTS AND CONNECTIONS
1. MOVING HEAD
2. ROTARY ARM
3. HANDLE
4. CONTROL PANEL with LCD display
and 5 button used to access
the control panel functions and
manage them.
5. LED INDICATOR "W-DMX"
6. LED INDICATOR POWER
7. ANTENNA
8. EtherCON connector Signal IN/
OUT
9. EtherCON connector Signal IN/
OUT
10. POWER IN (PowerCON TRUE
IN): for connection to a socket
(100-240V~/50-60Hz) via the
supplied mains cable.
11. DMX IN (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
12. DMX OUT (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
Fig.2
View A
View B
7
PANORAMAIPSPOT
Fig.3
CLAMP
SAFETY
CABLE
OMEGA
BRACKETS
- 2 - INSTALLATION
2.1 MOUNTING
The PANORAMAIPSPOT may be set up on a solid and even surface. By means of the xing facilities of the
baseplate, the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For
xing, stable mounting clips are required. According to the gure, the bolts of the brackets are placed into
the openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure
that the unit is rmly xed to avoid vibration and slipping while operating.The mounting place must be of
sucient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any
installation, always comply scrupulously with all the regulations (particularly regarding safety) currently
in force in the country in which the xture’s being used. Always additionally secure the projector with the
safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the
maximum fall of the projector will be 20 cm.
PANORAMAIPSPOT
8
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to
reset all motors to their home position. Shortly after that the PANORAMAIPSPOT is ready for operation.
To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-
mended to connect the unit to a socket which can be switched on and o via light switch.
3.2 BASIC
The PANORAMAIPSPOT has a LCD display and 5 button used to access the control panel functions and
manage them (g.4).
Fig.4 - Functions of the buttons and display icons
LEFT RIGHT UP DOWN ENTER BATTERY
Return to the top
level
Commute from
units, tens, hundred
in the menu
Increases the value
displayed or passes
to the previous item
in a menu
Decreases the value
displayed or passes
to the next item in
the menu
Conrms the
displayed value,
or activates the
displayed function,
or enters the
successive menu
Used to activate the
backup battery. It
allows to switching
display interface
without main power
SPOT
CONNECT LIGHT INFORMATION SET PROGRAM
Tabla de contenidos
Idiomas:
Otros manuales de Equipo de DJ de ProLights
ProLights
ProLights BATPAR180 Manual de usuario
ProLights
ProLights LEDPAR64363RGB Manual de usuario
ProLights
ProLights Tribe LUMIPIX12UQPRO Manual de usuario
ProLights
ProLights LUMIPAR18TRI Manual de usuario
ProLights
ProLights jetbeam-2 Manual de usuario
ProLights
ProLights TRIBE AQUA Manual de usuario
ProLights
ProLights ARENACOB4HALO Manual de usuario
ProLights
ProLights EclFresnel JrVW Manual de usuario
ProLights
ProLights ARCLED7307HD Manual de usuario
ProLights
ProLights TRIPLESCAN Manual de usuario
ProLights
ProLights ECLIPSETU Manual de usuario
ProLights
ProLights SMARTTUBE32 Manual de usuario
ProLights
ProLights RA2000PROFILEHB Manual de usuario
ProLights
ProLights Eclipse FC Manual de usuario
ProLights
ProLights PIXIEWASH Manual de usuario
ProLights
ProLights Pendant stations Manual de usuario
ProLights
ProLights LUMIPAR12HPRO Manual de usuario
ProLights
ProLights PFZ715 Manual de usuario
ProLights
ProLights ECLFRJPTU-DY Manual de usuario
ProLights
ProLights DISPLAYCOBTRWDFC Manual de usuario
Manuales populares de Equipo de DJ de otras marcas
thomann
thomann Stairville DJ Lase 40-G MK-III Manual de usuario
Eagletone
Eagletone 6 Eyes Flower Manual de usuario
EuroLite
EuroLite FLD-1508 Manual de usuario
Technical Pro
Technical Pro LG8xSEA Manual de usuario
JB Systems
JB Systems Lounge Laser DMX Manual de usuario
Lightmaxx
Lightmaxx Vega Halo 90 Manual de usuario
Elation
Elation FUZE WASH Z350 Manual de usuario
Maverick
Maverick MK3 WASH Manual de usuario
Infinity
Infinity TF-260C7 Fresnel Manual de usuario
Chauvet
Chauvet EVE E-50Z Manual de usuario
Eliminator Lighting
Eliminator Lighting E 138 Manual de usuario
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario