Progress Lighting Air Pro P2525 Manual de usuario

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

11221

PROGRESS LIGHTING 15-Year Limited Warranty

PROGRESS LIGHTING FAN MOTORS ARE WARRANTED TO THE END USER TO BE

FREE OF ELECTRICAL AND/OR MECHANICAL DEFECTS FOR A PERIOD OF 15

YEARS FROM DATE OF SALE. PULL CHAIN SWITCHES, REVERSE SWITCHES,

CAPACITORS AND METAL FINISHES ARE WARRANTEDFOR APERIOD OF 1 YEAR.

WARPING OF WOODEN OR PLASTIC BLADES IS NOT COVERED BY THIS

WARRANTY.

THE END USER HAS THE OPTION OF RETURNING THE DEFECTIVE FAN TO THE

PLACE OF PURCHASE DURING THE FIRST 30 DAYS FOR AREPLACEMENT. AFTER

30 DAYS, THE PURCHASER MUST CONTACT PROGRESS LIGHTING FOR REPAIR

OR REPLACEMENT. THE END USER ALSO BEARS THE RESPONSIBILITY FOR ALL

COSTS IN THE REMOVAL, SHIPPING AND REINSTALLATION OF FANS OR PARTS

FOR REPAIR OR REPLACEMENT.

PROGRESS LIGHTING WILL NOT ASSUME LIABILITY OR RESPONSIBILITY FOR

DAMAGES (INCLUDING INCIDENTAL OR CONSEQUENTIAL) CAUSED BY THE

IMPROPER INSTALLATION OR OPERATION OF THE UNIT OR ITS COMPONENT

PARTS, OR BY THE FAILURE OF SUPPORTING HARDWARE NOT SUPPLIED BY

PROGRESS LIGHTING. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER

GUARANTEES, WHETHER EXPRESSED OR IMPLIED, AND ISVOIDED IN CASES OF

ABUSE, MISUSE OR IMPROPER HANDLING, NEGLIGENCE, SHIPPING DAMAGE,

UNAUTHORIZED REPAIRS (MADE OR ATTEMPTED) OR UNUSUALAPPLICATION.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS

MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS AND

YOU MAY HAVE OTHER RIGHTSWHICH VARY FROM STATETO STATE.

15-Year Limited Warranty

785247147694 (BN)

785247147700 (WH)

Safety Rules.....................................................................................................................................

Unpacking Your Fan ........................................................................................................................

Installing Your Fan ...........................................................................................................................

..........................................................................................................................

Care of Your Fan ..............................................................................................................................

Troubleshooting .............................................................................................................................

Specifications ...............................................................................................................................

Operating Your Fan

10.

11.

Table of Contents

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breaker or fuse boxbefore beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan withany solid-state fanspeed control device.

4. WARNING: To reduce the risk of personal injury, use onlythe two steel

screws (and lock washers) provided with the outlet box for mounting to

the outlet box. Most outlet boxes commonly used for the support of

lighting fixtures are not acceptable for fan support and may need to be

replaced, consult aqualified electrician ifin doubt.

8. Avoid placing objectsin the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaningthe fan.

10. Do notuse water ordetergents when cleaningthe fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After marking electrical connections, spliced conductors should be

turned upward and pushed carefully up into outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side ofthe outlet box.

12. Electrical diagrams are reference only. Light kit that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use

Switches. Refer to the Instructions packaged with the light kits and

switches for properassembly.

WARNING

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TOOUTLET BOX MARKEDACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 pounds. Use only UL

Listed outlet boxesmarked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge ofthe blades tothe floor.

7. Do not operate reversing switch while fan blades are in motion. Fan

must be turnedoff and blades stopped beforereversing blade direction.

WARNING

TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE

BLADE BRACKETS (ALSOREFERRED TO AS FLANGES)DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

1. Safety Rules

Unpack your fanand check thecontents. You should have the following items:

7de

Unpacking Your Fan 2.

2. Mounting plate

Set of blades(5)

3. Fan motorassembly

4. Motor housing

5. Set ofblades bracket (5)

6. Balancing kit

7. Loose partsbag containing:

b. Blade bracket attachment hardware

(1 screws withlock washers)

(3 screws)

d. Motor housing hardware

(4 screws)

(4 plastic wireconnectors, 1 Pullchain)

a. Blade attachmenthardware

(16 screws, 16Fiber washers)

c. Mounting hardware

e. Electrical hardware

3. Installing Your Fan

Tools Required

Phillips screw driver, straight slot screw

driver, adjustable wrench, step ladder, and

wire cutters.

Mounting Options

If there isn't an existing ULlisted mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and buildingmaterials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs).Do not useplastic outlet boxes.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at yourProgress Lighting Retailer).

Outlet box

Figure 1

Figure 2

Figures 1,2 and 3 are examples of different

ways to mountthe outlet box.

WARNING

TO REDUCETHE RISK OFFIRE, ELECTRIC

SHOCK, OR OTHERPERSONAL INJURY,

MOUNT FAN ONLY TOAN OUTLETBOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THEMOUNTING SCREWS

PROVIDED WITHTHE OUTLET BOX. OUTLET

BOXES COMMONLY USEDFOR THE SUPPORT

OF LIGHTING FIXTURESMAYNOT BE

ACCEPTABLE FORFAN SUPPORT ANDMAY

NEED TOBE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IFIN DOUBT.

Figure 3

Hanging the Fan

REMEMBER to turn off the power.

Follow the steps below to hang your fan

properly.

1. Attach the mounting plate to the outlet box

using the screws two screws and washers

provided with the outlet box.(Fig. 4). For

best performance be sure the mounting plate

is level and secured firmly against the ceiling.

You may need to insert additional washers

(not provided) between the outlet box and

mounting plate to make it level.

2. Carefully Lift the fan motor assembly

(without the blades) and insert the T section

of the motor housing plate into the slot in the

mounting plate as shown in Fig. 5.

You are now ready to make the electrical

connections.

Figure 4

Figure 5

Outlet box

Mounting

plate

Screws

Outlet box

Solt

Fan

motor

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITEWHITE

BLACK

BLUE

GREEN

WHITE

BLUE

BLACK WHITE

Figure 6

Diagram indicates optionallight kit wiring.

WARNING

ELECTRICAL DIAGRAMSARE FOR

REFERENCE ONLY.OPTIONAL USEOF ANY

LIGHT KITSHALL BEUL LISTED AND

MARKED SUITABLEFOR USE WITHTHIS FAN.

Making the Electrical

Connections

Follow the steps below to connect the fan to your

household wiring. Use the wire connecting nuts

supplied with your fan. Secure the connectorswith

electrical tape. Make sure thereare no loose strands

or connections.

Step 1 Connect the fan supply (black) wire and

light supply (blue) wire to the black household

supply wire as shown inFigure 6.

Step 2. Connect the neutral fan (white) wire to the

white neutral household wire.

household

Step 4 After connecting the wires, spread them

apart so that the green and white wires are on one

side of the outlet box and the black wire is on the

other side.

REMEMBER to disconnect the power. If you feel

that you do not have enough electrical wiring

knowledge or experience, have your fan installed

by a licensed electrician.

Step 3 Connect the two green fan ground wires,

located on the mounting plate and motor, to the

ground wire.

WARNING

TO REDUCE THE RISKOF FIRE OR ELECTRIC

SHOCK, DO NOT USEA WALL MOUNTED

SOLID STATE SPEED CONTROLWITH THIS

FAN. IT WILLPERMANENTLYDAMAGE THE

ELECTRONIC CIRCUITRY.

Step 5 Turn the connecting nuts upward and

push the wiring into theoutlet box.

Finishing the

Installation

1. Swing the motor assembly up into position

under the mounting bracket. Secure the

bracket to the plate with the screws provided.

(Fig. 7)

2. Carefully lift the motor housing onto the

mounting plate, properly align the holes

and tighten the motor housing with the four

screws supplied.(Fig. 8)

Figure 7

Figure 8

Mounting

plate

Screws

Motor Mounting

plate

Screws

Motor

housing

Fiber

washer

Blade

arm

Figure 9

Blade

Screws

Attaching the Fan

Blades

Step 1 Attach the blades to the blade arms

using three screws and fiber washers as shown

in Fig. 9. Start a screw into the arm, do not

tighten. Repeat for the 2 remaining screws and

washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight.

NOTE: Your fan blades are reversible. Select

the blade side finish which best accentuates

your decor.

Fasten the blade assembly to the motor

using the motorscrews provided.

Step 3

(Fig. 10)

Step 4 Install an optional light kit if you wish.

Follow the instructionsincluded with thekit.

Figure 10

Motor

Blade arm

Blade blancing

deviation

3. Use the enclosed Blade Balancing Kit if

the blade wobbleis still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result insmoother operation.

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct

most fan wobbling problems. Check after

each step.

1. Check that all blade and blade arm

screws are secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 11. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance should be equal within

1/8".

Tabla de contenidos

Otros manuales de Admirador de Progress Lighting

Progress Lighting

Progress Lighting AirPro P2599 Manual de usuario

Progress Lighting

Progress Lighting P2529 Manual de usuario

Progress Lighting

Progress Lighting P2570 Manual de usuario

Progress Lighting

Progress Lighting AirPro P250016 Manual de usuario

Progress Lighting

Progress Lighting AirPro P250066 Manual de usuario

Progress Lighting

Progress Lighting AirPro P2552 Manual de usuario

Progress Lighting

Progress Lighting AirPro P250108 Manual de usuario

Progress Lighting

Progress Lighting EF200D Manual de usuario

Progress Lighting

Progress Lighting AirPro P2564-3030K Manual de usuario

Progress Lighting

Progress Lighting AirPro P2548 Manual de usuario

Progress Lighting

Progress Lighting AirPro P250062 Manual de usuario

Progress Lighting

Progress Lighting CALERA Manual de usuario

Progress Lighting

Progress Lighting AirPro P2544 Manual de usuario

Progress Lighting

Progress Lighting AirPro P250070 Manual de usuario

Progress Lighting

Progress Lighting 52-RDT Manual de usuario

Progress Lighting

Progress Lighting AirPro P250089 Manual de usuario

Progress Lighting

Progress Lighting AirPro P250032 Manual de usuario

Progress Lighting

Progress Lighting AirPro Claret P250007 Manual de usuario

Progress Lighting

Progress Lighting AirPro P2574-8030K Manual de usuario

Progress Lighting

Progress Lighting AirPro P2584-71 Manual de usuario

Progress Lighting

Progress Lighting P2500 Manual de usuario

Progress Lighting

Progress Lighting P2514 Manual de usuario

Progress Lighting

Progress Lighting P2550 Manual de usuario

Progress Lighting

Progress Lighting EF200D Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje