ProFlight Maverick PFBD95 Manual de usuario
Maverick
User Manual
Model: PFBD95
Thank you for choosing ProFlight.
Please read this user manual before using this drone and
keep it safe for future reference.
2of 17
CONTENTS
Safety…………………………………………………………………………………3
Battery Charging…………………………………………………………………4
Installing Controller Batteries……………………………………………..5
Transmitter Diagram…………………………………………………………..6
Folding the Arms..……………………………………………………………….6
Fitting Propeller Guards………………………………………………………7
Propeller Installation…………………………………………………………..7
Preparing for First Flight……………………………………………………..8
Binding of Radio Transmitter and Receiver…………………………8
Flight Instructions……………………………………………………………….9
Flight Adjustment………………………………………………………………10
Aircraft Functions & Features…………………………………………….11
Camera………………………………………………………………………………13
App…………………………………………………………………………………….14
Troubleshooting Guide………………………………………………………16
Support………………………………………………………………………………17
3of 17
SAFETY
Read the entire instruction manual and familiarise yourself with the product
and all its features before operating. Failure to operate the product correctly
can result in damage to the product, surroundings or even serious injury. This
product is not a toy and must be operated with caution and common sense. It
requires some basic mechanical knowledge. This product is not intended for
use by children without direct adult supervision. This manual contains
instructions for safety, operation and maintenance. It is essential to read and
follow all the instructions and warnings in this manual prior to assembly, setup
or use in order to operate correctly and avoid damage or serious injury.
Not intended for use by children under 14 years of age. This is not a toy.
Always operate your drone in open spaces away from vehicles, buildings,
traffic and people.
Always keep out of reach of children.
Avoid exposure to water as moisture can cause damage to the
electronics.
Never operate your drone with low transmitter batteries.
The battery charger included with the drone has been designed to safely
charge the Li-Po battery.
Mishandling of Li-Po batteries can result in a fire, personal injury, and
/or property damage.
By handling, charging or using the included Li-Po battery you assume all
risks associated with lithium batteries.
If at any time the battery begins to balloon or swell, discontinue use
immediately. If charging or discharging, discontinue and disconnect.
Continuing to use, charge or discharge a battery that is ballooning or
swelling can result in fire.
Always store the battery at room temperature in a dry area for best
results.
4of 17
Do not store battery or drone in a car or direct sunlight. If stored in a
hot environment, the battery can be damaged or even catch fire.
Never use any other type of battery charger other than the one supplied
with the drone. Failure to charge the battery with a compatible charger
may cause fire resulting in personal injury and/or property damage.
Never exceed the recommended charge rate.
When a Li-Po battery is discharged below 3.7V, the battery may be
damaged and may no longer accept a charge. The drone will
automatically land and become inactive when the battery reaches this
level, this is to protect the battery.
Battery Charging
Use only the enclosed USB Li-Po charger to charge your battery.
Remove the battery from the battery compartment at the rear of the aircraft.
Press down the release button on the underside of the aircraft and slide it out.
5of 17
Plug the charger into a USB socket before attaching the battery.
When the charger is plugged into the USB slot and charging the LED will
illuminate RED. When the battery is fully charged the LED will go out.
Charging should take around 60-70 minutes. DO NOT leave the battery
unattended whilst charging.
Installing the Controller Batteries
Unscrew the battery cover and insert 3 x AA Batteries, making sure the correct
polarity is followed, before reattaching the battery cover
6of 17
Transmitter Diagram
Folding the Arms
Please fold up the arms in the order 1 –4 following the diagram below.
The arms are unfolded by following the reverse of the above, until
the arms click into place.
7of 17
Fitting Propeller Guards
Carefully remove the blanking plate by levering it out using a fingernail or blunt
screwdriver. Push the propeller guide into the slot, pressing down where
indicated on the centre diagram to prevent damage to the guard.
Propeller Installation
Insert the propeller over the motor
spindle and use a screwdriver to
tighten the screw, then push the silver
cap into position over the screw.
Removal is the reverse of the above,
first carefully removing the silver cap
with a blunt object.
It is important for the correct
blade to be placed on the correct
motor or the aircraft will not fly
correctly. Each blade is marked
with an A or B on the underside to
indicate which motor it
corresponds to.
8of 17
Preparing for First Flight
1. Make sure both the transmitter and aircraft batteries are sufficiently
charged.
2. Find a suitable place to fly the aircraft, away from people, buildings and
vehicles.
3. Make sure the throttle stick is centred before turning on the transmitter.
Binding of Radio Transmitter & Receiver
1. Place the aircraft on a flat surface and insert the battery into the aircraft,
place the drone on a level surface, and turn it on using the button on the
underside
2. Turn on the controller.
3. The controller will beep
twice, and the red LED
will flash. Pair it to the
drone by pushing the
throttle stick to the top,
it will bleep, and then
pull the throttle stick to
the bottom.
4. The long bleep indicates it is paired and ready to fly
The aircraft can be flown using either the radio control supplied or by using the
App on a smart device. For details on flying with the App, see page 14.
9of 17
Flight Instructions
Before your first flight make sure you are familiar with the controls of the
aircraft.
Left Joystick –Throttle & Rudder
Right Joystick –Elevator & Aileron
The aircraft can only take off and land by pressing the take off / land button
(click once to take off and once to land). Once the aircraft is airborne it will
hold a steady hover, you are now in control of the aircraft and can use the left
and right sticks to control it.
Note: Should the aircraft be left for a while with no control inputs it will go to
sleep, simply press and hold the take off/land button to reactivate the aircraft.
10 of 17
Flight Adjustment
When you lift the Drone into the air, If the aircraft drifts in a particular
direction you can trim the controls using the trim buttons. Select the trim key
opposite the direction of drift. Trimming is always needed before your first
flight.
Auto Trim
To recover the drone back to the original
factory settings for trim. Press and hold
the two levers in the direction shown on
the diagram for a few seconds. The lights
on the drone will start to flash to confirm
this has completed.
Tabla de contenidos
