ProfiTap C8-1G Manual de usuario
CUSTOMER SUPPORT INFORMATION
To order or for technical information support:
Phone: +31 (0) 40 782 0880
Mail order: Profitap HQ B.V.
High Tech Campus 9
5656 AE Eindhoven - The Netherlands
Website: www.profitap.com
E-mail: [email protected]
C8-1G
High Density Gigabit Ethernet TAP
www.protap.com Page 2
Index Page
1. General information 3
2. Functional description 4
2.1. Interface connectors 4
2.2. LEDs: Speed/Link/Activity 4
2.3. Power 4
2.4. Power failure 4
3. Installation 5
4. Technical specifications 7
5. Safety 7
This package includes:
• 1 x C8-1G main unit
• 2 x C13 power cord
www.protap.com Page 3
1. General information
The C8-1G seamlessly duplicates all in-line
10/100/1000BASE-T traffic at wire speed. It monitors all 7 OSI
layers, and mirrors packets of all sizes and types, low-level
errors, and VLAN traffic.
The C8-1G is non-intrusive, has no IP address, and isolates
monitoring devices from the network. Once in place, it allows
monitoring devices to be connected and disconnected at will,
with no impact to the network link.
The C8-1G features redundant PSUs, allowing a second
power supply to activate in case the first power line were to
fail. In case of complete power failure, the C8-1G ensures that
the network link remains operational by instantly switching to
a fully passive mode.
www.protap.com Page 4
2. Functional description
2.1 Interface connectors
C8-1G features a total of 32 RJ45 ports, for 8 individual TAP
points. TAP points are numbered from 1 to 8.
Each TAP point consists of 4 ports. Network ports Net A and
Net B are connected in-line to the network. Monitor ports
Tap A and Tap B are connected to the analyzer.
2.2 LEDs: Speed/Link/Activity
LEDs indicate Speed, Activity and Link for each of the 32
ports. Speed LEDs light up when a link is detected on the
port, and blink when a signal is detected.
2.3 Power
C8-1G features two C14 inlets at the back of the unit. Each
inlet corresponds to one 100–240 VAC PSU. Connect a
power line to one inlet for normal operation. To make use of
the C8-1G’s redundant powering feature, connect each inlet
to a separate power line. Redundant powering ensures
maximum uptime of the unit. Two LEDs show the presence of
power.
2.4 Power failure
When both PSUs are unpowered, all Net (Network) ports are
switched a fully passive mode, and all Tap (Monitor) ports are
disabled. This ensures a permanent network link at all times.
www.protap.com Page 5
3. Installation
1. Before powering the C8-1G unit: connect one side of the
network link to Net A, and the other to Net B. Power both
network devices before powering the TAP.
Note: A powered TAP will always correct a wrong cable setup.
Connect the network using category 5e UTP cables.
In case of 10/100M network hardware which does not support
auto-crossover:
• If the network devices are of a different type (1 DTE and
1DCE), use 2 straight cables.
• If both network devices are of the same type (both DTE or
both DCE), use 1 straight and 1 crossover cable.
Connected network devices should show Link (or Activity). If
there is no Link, change one of the cables to one of an
opposite type.
www.protap.com Page 6
2. Power the TAP by connecting either PSU 1 or PSU 2 to a
power line. For redundant powering, connect both PSU 1 and
PSU 2, to separate power lines. Use the supplied C13 power
cords to connect to the C14 inlets at the back of the unit.
Safety notes:
• Use only power cords and power outlets with proper
earthing connection.
• The power outlets shall be kept easily accessible after
installation.
The Power 1 and Power 2 LEDs indicate power to PSU 1 and
PSU 2 respectively.
After negotiation of the highest mutual speed, the ports LEDs
indicate the network speed:
• Left LED for a 10M connection
• Right LED for a 100M connection
• Both LEDs for a 1G connection
Fast blinking LEDs on Net A and Net B indicate network
activity.
3. Connect the monitor ports, Tap A and Tap B, to the
analyzer, using straight or crossover category 5e cables.
The monitor ports operate at the same speed as the network
ports. The monitor ports’ LEDs light up when a link is found.
Network traffic received by Net A will be mirrored to Tap A,
and network traffic received by Net B will be mirrored to
Tap B.
The maximum distance between any of the connected
devices is 100 meters.
www.protap.com Page 7
4. Technical specifications
Connectors 32 x RJ45, 8-pin, gold plated
LEDs 64 x Link/Activity/Speed
2 x Power
Power supplies 2 x 100–240 VAC stabilized, 50–60Hz, 50W
Power consumption 50W
MTBF 150,000 hours
Enclosure Steel and aluminum, structured black oven
painted
Dimensions (WxDxH) 440 x 260 x 44 mm
17.3 x 10.2 x 1.7 in
Weight 3.6 kg
7.94 lb
Operating temperature 0°C to 50°C
Storage temperature -20°C to 70°C
Humidity 10 to 90%, non-condensing
Certifications
RoHS
CE
FCC class A
IEEE 802.3 compliant
5. Safety
• This equipment is not suitable for use in locations where
children are likely to be present.
• This device features more than one power supply unit.
Disconnect ALL power cords before servicing the device, to
avoid any risk of electrical shock.
• Do not push or force any objects through any opening in the
chassis frame, as it could result in electrical shock or fire.
• Avoid spilling liquid onto the device, as it could cause
electrical shocks or damage the device.
Disclaimer
The information in this document is subject to change without notice.
The manufacturer makes no representations or warranties with respect
to the contents hereof and specifically disclaims any implied warranties
of merchantability or fitness for any particular purpose. The
manufacturer reserves the right to revise this publication and to make
changes in the content hereof without obligation of the manufacturer to
notify any person of such revision or changes.
Warranty and Liability
Profitap warrants that this product is free from defects in material and
workmanship at time of shipment. The warranty period is 2 years from
the date of purchase. The standard 2 year warranty period may be
extended at the time of order. Profitap assumes no liability for products
that have been subjected to abuse, modification, misuse, or if the model
or serial number has been altered, tampered with, defaced or removed.
Profitap is not liable under any contract, negligence, strict liability or
other legal or equitable theory for any loss of use of the product,
inconvenience or damages of any character, whether direct, special,
incidental or consequential (including, but not limited to, damages for
loss of goodwill, loss of revenue or profit, work stoppage or malfunction)
Copyright
This publication, including all photographs and illustrations, is protected
under international copyright laws, with all rights reserved. Neither this
manual, nor any of the material contained herein, may be reproduced
without written consent of the author
Trademarks
The trademarks mentioned in this manual are the sole property of their
owners.
v4.5
Profitap HQ B.V.
High Tech Campus 9
5656 AE Eindhoven
The Netherlands
+31 (0) 40 782 0880
www.profitap.com
Tabla de contenidos
Otros manuales de Hardware de red de ProfiTap
ProfiTap
ProfiTap F4-10G-BP BYPASS TAP Manual
ProfiTap
ProfiTap X2-3200G Manual de usuario
ProfiTap
ProfiTap XX Series Manual de usuario
ProfiTap
ProfiTap X2 Series Manual de usuario
ProfiTap
ProfiTap C1R-1G Manual de usuario
ProfiTap
ProfiTap X2-3200G Manual de usuario
ProfiTap
ProfiTap PROFISHARK 1G Manual de usuario
ProfiTap
ProfiTap F1-10G-BP BYPASS TAP Manual
ProfiTap
ProfiTap PROFISHARK 100M Manual de usuario
ProfiTap
ProfiTap F1-40G-BP BYPASS TAP Manual
ProfiTap
ProfiTap IOTA 1G Manual de usuario
ProfiTap
ProfiTap PROFISHARK 1G+ Manual
ProfiTap
ProfiTap C1-100 Manual de usuario
ProfiTap
ProfiTap C1D-1G Manual de usuario
ProfiTap
ProfiTap C1-1G-RG2 Manual de usuario
ProfiTap
ProfiTap XX Series Manual de usuario
ProfiTap
ProfiTap 10GBASE-T Manual de usuario
ProfiTap
ProfiTap IOTA 1G Manual de usuario
ProfiTap
ProfiTap ProfiShark 10G Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
