Procomp BVD2A Manual de usuario
BVD2A
~0~
Safety and Regulatory Information
Notice for the USA
FCC Part 15: This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
withtheinstructions,maycauseharmfulinterferencetoradiocommunications.
However, this notice is not a guarantee that interference will not occur in a
particular installation.
CAUTION: To comply with the limits for the class B device, pursuant to
Part 15 of the FCC Rules, this device must be installed in computer equipment
certified to comply with the Class B limits.
All cables used to connect the computer and peripherals must be shielded and
grounded. Operation with non-certified computers or non-shielded cables may
result in interference to radio or television reception.
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the device.
COPYRIGHT: This publication, including all photographs, illustrations
and software, is protected under international copyright laws, with all rights
reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without the express written consent of the manufacturer.
DISCLAIMER: The information in this document is subject to change
without notice. The manufacture makes no representations or warranties with
respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose.
BVD2A
~1~
TABLE OF CONTENTS
CH1. MOTHERBOARD FEATURE INTRODUCTION....................... 2
1.1 ABOUT THE MANUAL.................................................. 3
1.2 SPECIFICATIONS........................................................ 3
1.3 POWER OFF CONTROL SOFTWARE .......................... 5
1.5 PACKAGING CHECK LIST........................................... 6
CH2. SETUP GUIDE...................................................................... 7
2.1 MOTHERBOARD LAYOUT........................................... 7
2.2 CONNECTOR & JUMPER REFERENCE....................... 8
2.3 THE SETUP STEPS..................................................... 9
2.3-1 JUMPER & CONNECTOR SETTING.................... 9
2.3-2 MEMORY INSTALLATION..................................18
2.3-3 HOW TO INSTALL THE CPU..............................21
2.3-4 INSTALLING THE MOTHERBOARD ...................23
2.3-5 INSTALLING AN INTERFACE CARD ..................24
2.3-6 INSTALLING ACCESSORY CABLES..................25
CH3. AWARD BIOS SETUP.........................................................27
3.1 THE MAIN MENU........................................................29
3.2 STANDARD CMOS FEATURES...................................32
3.3 ADVANCED BIOS FEATURES.....................................34
3.4 ADVANCED CHIPSETFEATURES..............................38
3.5 INTEGRATED PERIPHERALS.....................................41
3.6 POWER MANAGEMENT.............................................42
3.7 PNP/PCI CONFIGURATIONS ......................................48
3.8 PC HEALTH STATUS..................................................49
3.9 FREQUENCY/VOLTAGE CONTROL............................50
3.10 LOAD FAIL-SAFE DEFAULTS....................................51
3.11 LOAD OPTIMIZED DEFAULS ....................................51
3.12 SET SUPERVISOR PASSWORD/USER
PASSWORD.....................................................................51
3.13 SAVE AND EXIT SETUP............................................52
3.14 EXIT WITHOUT SAVING ...........................................52
CH4. SOFTWARE SETUP............................................................53
4.1 INSTALLING THE IDE BUS MASTER DRIVER.............53
BVD2A
~2~
Congratulations on purchasing the BVD2A motherboard. We are certain it
will provide you with many years of outstanding and reliable performance.
Based on the VIA Pro-Plus 133A chipset, theBVD2Acomes with a Socket
370 interface and supports Intel Celeron PPGA and Intel Coppermine FCPGA
processors operating at speeds ranging from 300 to 750MHz . An ATX-sized
board, the BVD2A measures 210mm by 305mm and includes AGP, ISA and
PCI expansion slots, as well as three DIMM sockets for adding up to 768MB
of memory.
TheBVD2A’ sclock generator can operate at speedsof 66, 100 or 133 MHz,
and up to 256MB of RAM may be added to each of the board’s three DIMM
sockets. In addition, the BVD2A comes with one AGP, two ISA and five PCI
slots for the addition of devices such asgraphics adapters, modems and sound
cards. One ISA and one PCI slot are shared, meaning you may connect either
two ISA and four PCI cards or one ISA and five PCI cards.
The board has a 2MB Award PnP BIOS with enhanced ACPI features. Not
only does the BIOS support 120MB ATAPI floppy disk and ZIP disk drives, it
also allows multiple boots from a wide selection of IDE, SCSI, CD-ROM and
FDD drives. The Trend ChipAway AntiVirus protection built into the BIOS
helps ensure that your system remains virus-free. The BIOS also comes with
system heat and fan speed detectors, and can be configured to generate a
warning if user-defined fan speeds or temperatures are exceeded.
Other advanced features include keyboard and mouse power-on, a
wake-on-LAN header, wake-up alarm support, HDD S.M.A.R.T. error
detection, and PC’99-compliant color-coded connectors. The BVD2A comes
with one parallel port, two serial ports, two USB ports, a PS/2 mouse port, and
a PS/2 keyboard port.
Chapter 1
Motherboard Feature Introduction
BVD2A
~3~
The BVD2A motherboard is a high-performance device that offers full
functionality at a low cost. Its ease of use and reliability will become evident
from the very start.
1.1 ABOUT THE MANUAL
This manual contains the following information:
CH1. Motherboard Feature Introduction –Introduces the features of the
BVD2A board, and provides a checklist of items that are shipped with
the package.
CH2. Setup guide–Guidelines on how to install the motherboard and how to
get your system up and running.
CH3. Award BIOS Setup –Explanation of the BIOS setup items, for
configuring your motherboard for optimum performance.
CH4. Software Setup –How to install the software drivers and support
programs that are provided with this motherboard.
1.2 SPECIFICATIONS
System Chipset VIA Apollo Pro-Plus 133A
(VT82C694X and VT82C596B)
with AGP solution.
Processor Intel Socket370 PPGA and FCPGA
at 300MHz ~ 750MHz
Bus
Architecture
AGP/PCI/ISA
BVD2A
~4~
Architecture
Clock Generator 66, 100, up to133Mhz
DRAM Modules 168 pin DIMMs x 3, max. 256MB each
Supports total of 8MB to 768MB SDRAM.
BIOS
2MB Award PnP BIOS with enhanced ACPI feature for
PC98 compliance.
Supports 120MB ATAPI floppy disk.
Supports ZIP disk drive.
Supports multi-boot from IDE,SCSI,CD-ROM and FDD.
Supports software clock control.
Supports Trend™ ChipAway AntiVirus.
Supports HDD S.M.A.R.T.
On Board I/O
1 Floppy port (up to 2.88MB, 3 mode floppy supported
& LS-120).
2 Serial ports, 1 Parallel port (SPP/EPP/ECP).
2 USB, 1 PS/2 mouse, 1 PS/2 keyboard.
1 IrDA.
On Board IDE
Port Dual Ultra DMA 33/66 IDE ports
Supports ATAPI IDE CD-ROM & LS-120.
Expansion slot 1 x 64-bit AGP slot. Supports AGP 4X Mode
5 x 32-bit PCI slots. (5 Master, 1 Share)
2 x 16-bit ISA slots. (1 Share)
I/O Chip Winbond super I/O W83977TF-AW.
Other Feature
Supports keyboard & mouse power on feature with ATX
power.
Supports Wake-up by Alarm
Wake-up On LAN header.
Board Size ATX form factor
Size : 305mm x 210mm (12" x 8.26")
BVD2A
~5~
1.3 POWER OFF CONTROL SOFTWARE
The motherboard design supports the software power off Control feature
through the SMI code in the BIOS under a Windows9x operating system
environment. This is an ATX form factor feature, so you should use ATX
power supply in order to enable it.
First, connect the power switch cable (provided by the ATX/AT case
Supplier) to the connector [ PWBT ] on the motherboard (Please refer to the
illustration below). In the BIOS screen of “POWER MANAGEMENT
SETUP”, choose “User Defined” (or Min power saving or Max power saving)
in “POWER MANAGEMENT” and choose “Yes” in “PM Control by APM”.
Note: Refer to “Chapter 3: Award BIOS Setup” for more
information on the BIOS Setup
In Windows 9x, when using the “SHUT DOWN” function, the computer
will switch off automatically and put the PC in a suspend mode. This will be
indicated by a blinking power light indicator. To restart the system, simply
press the Power Button.
PS_BT
BVD2A
~6~
1.4 PACKAGING CHECK LIST
The Motherboard comes securely packed in a gift box and shipping carton.
Ifanyoftheitemsbelowaremissingordamaged,pleasecontactyoursupplier.
The motherboard package list contains:
Q’TY Description
1Motherboard : With VIA Apollo Pro-Plus 133A chipset
1Driver
: CD-Title
• PC-Cillin Software
• Motherboard Bus master Driver
1Cable : IDE Cable
1Cable : Floppy Cable
1Manual :User’s manual
BVD2A
~7~
2.1 Motherboard Layout
Chapter 2
Setup Guide
VIA Apollo
Pro-Plus 133A
Chipset
PCI Slot x 5
ATX Power
DIMM x 3
T: Mouse
B: K/B
ISA Slot x 2
IDE Port x 2
AGP Slot
FDD Port
USB 1/2
T: LPT1
B: COM 1/2
SOCKET 370
BVD2A
~8~
2.2 Connector & Jumper Reference
COM1
MS
KB USB COM2
LPT
Socket 370
FAN1
FAN3
JP6
DIMM1
DIMM2
DIMM3
FDC ATX POWER
Connector
FAN2
IDE 2
IDE 1
AGP SLOT
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
ISA 1
ISA 2
IrDA
BIOS
Connector Front View
WOL
JP7
JBAT1
3V
Battery
SUPER
I/O
JP1
JP17
J1
WOM
BVD2A
~9~
2.3 The setup steps
refer to the following steps to setup your computer:
I. Refer to the Jumper Setup section to set up the jumpers appropriately.
II. Install the DIMM modules on the motherboard; be sure to install
them correctly.
III. Install the CPU on the motherboard (please refer to the CPU
installation manual).
IV. Choose a case and install the motherboard into the case.
V. Plug in all the interface cards of your system equipment.
VI. Connect cables, power supply and any message lines.
VII. Reboot, and enter the Award BIOS setup Menu to adjust the existing
setup to your needs.
VIII. Reboot, and set up the system software on your computer.
2.3-1Jumper & Connector Setting
PS/2 Keyboard Connector
Use this connector to connect a PS/2 Keyboard.
Pin Description Pin Description
1Keyboard Data 2,6 N.C.
3Ground 4+5V
5Keyboard Clock
Tabla de contenidos
Otros manuales de Placa madre de Procomp
Procomp
Procomp BS61M Series Manual de usuario
Procomp
Procomp BVK1A Manual de usuario
Procomp
Procomp BIW2A Manual de usuario
Procomp
Procomp B785 Manual de usuario
Procomp
Procomp BIW1A Series Manual de usuario
Procomp
Procomp b598 Manual de usuario
Procomp
Procomp B683 Manual de usuario
Procomp
Procomp B687 Manual de usuario
Procomp
Procomp b686 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
