Pro-tec 193762 Manual de usuario
PRO-TEC SENTRY BUILDING
AWNING MANUAL
IMPORTANT - TO THE DEALER OR ERECTOR:
RETURN THIS MANUAL TO THE OWNER FOR THEIR FUTURE REFERENCE
SIOUX STEEL COMPANY, P.O. BOX 1265, SIOUX FALLS, SOUTH DAKOTA 571 1
1-800-557-4689
MANUAL NO. 193762
REV D/MRS 8/1/17 ECN 17-141
TABLE OF CONTENTS
SAFETY PAGE 2
TOOLS & EQUIPMENT PAGE 3
COMPONENTS PAGE 4
40' AWNING FRAME PAGE 5
50' AWNING FRAME PAGE 6
60' AWNING FRAME PAGE 7
70' AWNING FRAME PAGE 8
80' AWNING FRAME PAGE 9
90' AWNING FRAME PAGE 10
EAVE INSTALLATION PAGE 11
40' TO 50' RATCHET MOUNT INSTALLATION PAGE 12
60' TO 80' RATCHET MOUNT INSTALLATION PAGE 13
90' RATCHET MOUNT INSTALLATION PAGE 14
COVER SPLICE BRACKET PAGE 15
MAINTENANCE SCHEDULE PAGE 16-17
WARRANTY STATEMENTS PAGE 18
1
SAFETY
Watch for this symbol. It points out important safety
precautions. It means “Attention – Be Alert!”
DEFINITIONS:
CAUTION: Indicates a hazardous situation, which, if not avoided, could result in
minor or moderate injury.
WARNING: Indicates a hazardous situation, which, if not avoided, could result
in death or serious injury.
DANGER: Indicates a hazardous situation, which, if not avoided, will result in
death or serious injury.
When assembling building:
Use appropriate safety practices during assembly of building. Hard hats are
recommended to prevent injury to head. Gloves and other heavy clothing are
recommended to prevent cuts and abrasions to hands and other body parts.
Beware of all pinch points when assembling building components. Appropriate
erection equipment and proper training in the operation of this equipment, are
important factors for the safe erection of building. Reading, understanding, and
following the instructions in this book are also very important for the safe
assembly of this building. Sioux Steel Company includes all reasonable means
for accident prevention, except a safe and careful operator.
If any decals become damaged, detached, or illegible, contact your dealer or
Sioux Steel Company at (800)-557-4689 for free replacements.
After building is complete:
To assure building remains safe, follow the maintenance schedule found at the
end of this manual.
If building is damaged:
If damage to building occurs, access in or around building should be restricted to
inspection only. Immediately contact your dealer or Sioux Steel Warranty
Department at (800) 557-4689. Repair of damages should be implemented as
soon as practical, with appropriate PRO-TEC replacement parts.
2
TOOLS AND EQUIPMENT
Drilling Tools: Power drill
3/16” drill bit (for pilot drilling drill screws)
17/32” drill bit (for1/2" bolts)
3/8” power driver (for drill screws)
Measuring Tools: 25' Tape measure
Hand Tools: Socket & wrench size 3/8” & 3/4"
Impact Wrench (pneumatic or electric)
Special Tools: Movable scaffolding or man lift
Material (Customer Supplied):
Duct Tape
BOLT INSTALLATION
Bolts should be installed to a snug-tight condition, which is defined as: the
tightness attained by either a few impacts of an impact wrench or the full effort of
a worker with a wrench that brings the connected plates in to a firm contact.
3
189285
3" TUBE CAP
187299
DRILL SCREW, 1/4" X 3/4"
EAVE 3"
193388GRY - 10FT
194098GRY - 12FT
189987GRY - 16FT
190006
1/2" x 3 1/2" BOLT
SCALE (1:2)
SWAGED EAVE 3"
193389GRY - 10FT
194100GRY - 12FT
189988GRY - 16FT
2" MOUNT
40' TO 80'
189992GRY
90'
194105GRY
UPPER TUBE
157630
DRILL SCREW, 1/4" x 1 1/4"
COMPONENTS
189515
1/2" NYLOCK
NUT SCALE (1:2)
2" MOUNT PLATE
(USED ON END
RAFTERS)
90'
194104GRY
40' TO 80'
189993GRY
BRACE ARM
163753
1/2" x 4" BOLT
SCALE (1:2)
191750
1/2" x 4 1/2" BOLT
SCALE (1:2)
HORIZONTAL ARM
4
7'-5 1/8"
3'-8 1/8"
90.0°
1'-1 1/8"
8'-3 3/8"
4 1/2"
1'-1 1/2"
1 1/2"
HOLES
(3) 189515- 1/2" NYLOCK NUT
DRILL SCREWS
(8) 1/4" X 1 1/4"
(8) 157630- 1/4" X 1 1/4" DRILL SCREW
PRE-DRILLED
BOLT
1/2" X 3 1/2"
(1) 196301GRY HORIZONTAL ARM
(1) 196303GRY BRACE ARM
(1) 196299GRY UPPER TUBE
(3) 190006- 1/2" x 3 1/2" BOLT
Step 1.1 Install Upper Tube as shown in drawing by drilling 17/32" clearance hole into rafter
and then securing with 1/2" bolt and nut.
Step 1.2 Assemble Horizontal Arm and Brace Arm to Upper Tube utilizing existing pre-drilled
holes and 1/2" bolts and nuts as shown in drawing.
Step 1.3 Utilizing 1/4" drill screws, attach Horizontal Arm and Brace Arm to rafter as shown
in drawing.
Step 1.4 Proceed to step 2.
STEP 1- 40' AWNING FRAMING
HOLE
DRILL 17/32"
1/2" NUT
UPPER
TUBE
ARM
HORIZONTAL
BRACE
ARM
1/2" NUT
1/2"
NUT
1/2" X 3 1/2"
BOLT
5
1/2" NUT
1/2"
NUT
1/2" X 3 1/2"
BOLT
HOLE
DRILL 17/32"
1/2" NUT
UPPER
TUBE
ARM
HORIZONTAL
BRACE
ARM
STEP 1- 50' AWNING FRAMING
(1) 196303GRY BRACE ARM
(1) 196299GRY UPPER TUBE
(3) 190006- 1/2" x 3 1/2" BOLT
(3) 189515- 1/2" NYLOCK NUT
(8) 157630- 1/4" X 1 1/4" DRILL SCREW
(1) 196301GRY HORIZONTAL ARM
Step 1.4 Proceed to step 2.
in drawing.
HOLES
PRE-DRILLED
BOLT
1/2" X 3 1/2"
DRILL SCREWS
(8) 1/4" X 1 1/4"
Step 1.1 Install Upper Tube as shown in drawing by drilling 17/32" clearance hole into rafter
and then securing with 1/2" bolt and nut.
Step 1.2 Assemble Horizontal Arm and Brace Arm to Upper Tube utilizing existing pre-drilled
holes and 1/2" bolts and nuts as shown in drawing.
Step 1.3 Utilizing 1/4" drill screws, attach Horizontal Arm and Brace Arm to rafter as shown
6
(1) 196289GRY UPPER TUBE
(1) 163753- 1/2" x 4" BOLT
(1) 196296GRY BRACE ARM
(2) 190006- 1/2" x 3 1/2" BOLT
STEP 1- 60' AWNING FRAMING
(1) 196292GRY HORIZONTAL ARM
(8) 157630- 1/4" X 1 1/4" DRILL SCREW
(3) 189515- 1/2" NYLOCK NUT
Step 1.4 Proceed to step 2.
in drawing.
HOLES
PRE-DRILLED
DRILL SCREWS
(8) 1/4" X 1 1/4"
BOLT
1/2" X 4"
Step 1.1 Install Upper Tube as shown in drawing by drilling 17/32" clearance hole into rafter
and then securing with 1/2" bolt and nut.
Step 1.2 Assemble Horizontal Arm and Brace Arm to Upper Tube utilizing existing pre-drilled
holes and 1/2" bolts and nuts as shown in drawing.
Step 1.3 Utilizing 1/4" drill screws, attach Horizontal Arm and Brace Arm to rafter as shown
1/2" NUT
1/2" X 3 1/2"
BOLT
1/2"
NUT
1/2" X 3 1/2"
BOLT
HOLE
DRILL 17/32"
1/2" NUT
UPPER
TUBE
ARM
HORIZONTAL
BRACE
ARM
7
(1) 196289GRY UPPER TUBE
(1) 163753- 1/2" x 4" BOLT
(8) 1/4" X 1 1/4"
(1) 196296GRY BRACE ARM
(2) 190006- 1/2" x 3 1/2" BOLT
STEP 1- 70' AWNING FRAMING
(1) 196292GRY HORIZONTAL ARM
(8) 157630- 1/4" X 1 1/4" DRILL SCREW
(3) 189515- 1/2" NYLOCK NUT
DRILL SCREWS
Step 1.4 Proceed to step 2.
in drawing.
HOLES
PRE-DRILLED
Step 1.1 Install Upper Tube as shown in drawing by drilling 17/32" clearance hole into rafter
and then securing with 1/2" bolt and nut.
Step 1.2 Assemble Horizontal Arm and Brace Arm to Upper Tube utilizing existing pre-drilled
holes and 1/2" bolts and nuts as shown in drawing.
Step 1.3 Utilizing 1/4" drill screws, attach Horizontal Arm and Brace Arm to rafter as shown
DRILL 17/32"
1/2" NUT
HOLE
1/2" X 4"
BOLT
UPPER
TUBE
ARM
HORIZONTAL
BRACE
ARM
1/2" NUT
1/2" X 3 1/2"
BOLT
1/2"
NUT
1/2" X 3 1/2"
BOLT
8
(1) 196289GRY UPPER TUBE
(1) 163753- 1/2" x 4" BOLT
(8) 1/4" X 1 1/4"
(1) 196297GRY BRACE ARM
(2) 190006- 1/2" x 3 1/2" BOLT
STEP 1- 80' AWNING FRAMING
(1) 196292GRY HORIZONTAL ARM
(8) 157630- 1/4" X 1 1/4" DRILL SCREW
(3) 189515- 1/2" NYLOCK NUT
DRILL SCREWS
Step 1.4 Proceed to step 2.
in drawing.
HOLES
PRE-DRILLED
Step 1.1 Install Upper Tube as shown in drawing by drilling 17/32" clearance hole into rafter
and then securing with 1/2" bolt and nut.
Step 1.2 Assemble Horizontal Arm and Brace Arm to Upper Tube utilizing existing pre-drilled
holes and 1/2" bolts and nuts as shown in drawing.
Step 1.3 Utilizing 1/4" drill screws, attach Horizontal Arm and Brace Arm to rafter as shown
UPPER
TUBE
ARM
HORIZONTAL
BRACE
ARM
DRILL 17/32"
1/2" NUT
HOLE
1/2" X 4"
BOLT
1/2" NUT
1/2" X 3 1/2"
BOLT
1/2"
NUT
1/2" X 3 1/2"
BOLT
9
Tabla de contenidos
Otros manuales de Accesorios de Pro-tec
