PRO.SIS.TEL. LOG2010 Manual de usuario
LOG2010 (20-17-15-12-10m)
Assembling procedures:
After you open the box, find and prepare parts as following:
Handle wi h care he preassembled par s.
Boom use square pipes.
Front and back elements use round pipes
All measure are me rics in mm.
Be aware, put a little lubrification on stainless steel bolts because if screwed down fast, getting hot,
could stiff, (general rules alid for all stainless steel bolts).
Arrange square pipe, in line, in a stepping down sequence following labels and drawing.
Innestare i tubi l’uno dentro l’altro, ed imbullonarli tra loro con gli appositi bulloni. Le teste dei
Insert the smaller square pipe end in the larger square pipe end, insert the bolt from bottom to top
side and make sure that bolt head take place in the larger hole pressing on the inner square pipe.
Boom
The A label joints are on the front side, the B label joints are on the rear antenna side, both refered
to mast-boom joint plate.
On the antenna boom are preinstalled already the wire elements insulators and RF wire line. After
that the boom is completed, connect the line wires to next one, taking care to cross them.
RF wire line, back and front alluminum elements take place on the bottom boom face.
If you are assembling antenna on easels, pre enting RF line wires damages, disconnect them in
coincidence with easel, taking care to reconnect them back when assembling end.
If you ha e easy access to your tower rotating mast pipe , than install boom-mast plate on the
antenna boom and install it on the tower, taking care to ha e RF lines and insulators facing down.
Take out from the package the back dipole round tubes, you will get them preassembled, just pull
them out from the main pipe, following the tube tapering sequence, find the connection holes, when
they are coincident, put and screw down the bolt, make sure to ha e the bolt head down in the larger
hole as in the picture below. Don’t forget to lubrificate a bit the stainless steel bolts.
Screw down all nuts. Make sure that all bolt heads are aligned on the same side.
Follow the same procedure for all tube connections.
When you ha e both half alluminum element ready, than procede to assembly the center as in the
picture below. Make sure to ha e 8cm in between the line connection bolts.
Cen er view of back elemen dipole (long one)
When back element is assembled do the same procedure with front element as in the picture below
Cen er view of he fron dipole (shor one)
Boom-mast plate
After than you ha e installed antenna boom on the mast procede to install both alluminum dipoles
on the boom bottom face. Install the short one on the front side, using four 80x6MA bolts and
predrilled square counter-plate. Install the long one on the back side using four 80x6MA bolts as
counter plate use the foot of the upholder wires pipe. In both cases insert bolts from bottom side.
Before to screw down the self-looking nuts, check that both dipoles are correctly spaced from the
nearest element, Make sure that they are in square and screw down the bolts to ha e a solid cross.
Install the top trussed wire doing a knots on the back eye bolt, pass trought the uphold pipe hole and
go to the front side eye bolt, pull to ha e the boom a little bit bended on the upper side, (banana
effect) and close down the knot. Install in the same way, the back dipole upper guy wire, to ha e it
like a gull wings.
In the package you will find two rolls of black UV resistant plastic wire. They are the external
insulated loop on which will take places the wires elements ends.
Find the end ha ing the eye and install it on the bolt coming out from the boom, front side, screw
down a self-looking nut, so the eye can’t come loose. Next one, mo ing toward the plastic wire, you
will find a short piece of alluminum with an insulator, fit the insulator in the alluminum dipole end,
walk going at back dipole, fit the short black round insulator in the dipole end, and than go to the
boom end and insert the turnbuckle eye on the bolt end coming out from the boom pipe.
Follow the same procedure with the second one half loop. When both wires are in place, pull wires
screwing the turnbuckle. Make sure that both half loop are well balanced looking toward the boom,
it MUST be straight.
In the package there are 6 couple of steel wires elements, they are gal anized steel, protected with
black UV resistent PVC with both ends eye terminated. Unroll the wires elements, select them by
longer to shorter. Get the longer wires couple and starting from the back antenna side, connect each
one element end to his correspondent RF line, one eye to the insulator bolt, the other one end on
the corrispondet U bolt placed on the main loop insulated wire. Repeat this procedure for all
elements.
Install balun 1:2 and connect both wire end to RF line, connect the coax line taking care to run it
on the upper boom face use plastic belts or tape to hold it in place.
New Balun ersion
Main an enna diagram – Top view
Back side view Side view Fron
When completed antenna will looks like the one in the picture.
Af er han all par s are assembled make sure ha all nu s are igh ned
Images and drawings are for information purposes only and may not be the same as the
finished product, the manufacturer reserves the right to make changes or modifications
without prejudice to the final specifications.
Fea ures:
Antenna perform in the range 13-30Mhz, optimized in coincidence with Ham radio bands.
Performance may change due en ironimental conditions in which is installed.
Take care to install it at least 5 or more meters (15 or more ft) o er the ground.
Bands: 20-17-15-12-10m
Impedence: 50 ohm with original 2:1 balun installed
SWR: < 1:1,5
Boom 5,9m + 1,8m (18+6ft)
Accept Mast 50mm (2in) or 60mm. (optional)
Rotating 5.4m (17ft)
Weight about 20Kg (44lbs)
Average gain 6-9 Dbi
F/B 10 - 20dB
Maximum power 3KW pep ssb
Wind survive: 130Km/h
WARNING!!!
Do no ins all he an enna in he vicini y of exposed power lines or o her sources of power a
risk of ligh ning, you may be killed or seriously injured. Make sure anyone does no even
come in o con ac wi h i acciden al during use
Ins all he an enna on properly dimensioned suppor s o hold he load even under s ormy
wind condi ions.
The fall of all or par of i could hi people and / or hings wi h unrecoverable damages.
In case, he responsibili y is o be solely charged by he user.
This manual is an in egral par of he produc , keep i handy.
Dear buyer,
thank you for purchasing a Pro.Sis.Tel antenna ..
Making it we have used the best materials available on the market, worked and finished
with the best care possible allowed by the state of art.
Use it within the rating for which it was built and will serve you faithfully for many years.
In case of doubts or concerns, our technical department is always ready to provide all the
necessary help.
If you are satisfied with it tell the others, otherwise ...... tell to us.
Your opinion and your suggestions will help us to improve even more our products.
Best regards
nnamaria Fiume IK7MWR
Made in Italy
W RNING! Defend the environment
isposing components and materials
The antenna consists mainly of aluminum, in the event of disposal, conferred the scrap to a specialized
disposal center, in compliance with the requirements of local law.
Tabla de contenidos
Otros manuales de Antena de PRO.SIS.TEL.
PRO.SIS.TEL.
PRO.SIS.TEL. PST-34TV Manual de usuario
PRO.SIS.TEL.
PRO.SIS.TEL. PST-1524TV Manual de usuario
PRO.SIS.TEL.
PRO.SIS.TEL. PST-30VF Manual de usuario
PRO.SIS.TEL.
PRO.SIS.TEL. PST-DDR5 Manual de usuario
PRO.SIS.TEL.
PRO.SIS.TEL. PST152VC Guía de instalación
PRO.SIS.TEL.
PRO.SIS.TEL. PST-152TV Manual de usuario
PRO.SIS.TEL.
PRO.SIS.TEL. PST Manual de usuario
PRO.SIS.TEL.
PRO.SIS.TEL. PST-RD34T Manual de usuario
PRO.SIS.TEL.
PRO.SIS.TEL. PST-32 Guía de instalación
PRO.SIS.TEL.
PRO.SIS.TEL. PST-27 Guía de instalación
Manuales populares de Antena de otras marcas
Alfa Network
Alfa Network APA-L01 Manual de usuario
Naval
Naval PR-422CA Manual de usuario
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario
TERK Technologies
TERK Technologies TV44 Manual de usuario
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manual de usuario
HP
HP J8999A Manual de usuario
