Pro's Kit PT-1362U Manual de usuario

PT-1362U

USB LI-ION CORDLESS SCREWDRIVER 3.6V

User’s Manual

1st Edition,

SAFETY INSTRUCTIONS

WARNING: Read the safety warnings and all instructions before use.

Failure to follow the warnings and instructions may result in electric

shock, fire and/or serious injury. Save all warnings and instructions

for future reference.

Work area

1. Always keep work area clean and bright. Cluttered and dark areas

easily induce accidents.

2. Do not operate power tools on explosive atmospheres, such as

flammable liquids, gases or dust. Power tools may cause sparks

to ignite the dust of fumes.

3. Keep children and bystanders away while operating a power tool.

Distractions could cause you to lose control.

Electric safety

1. Power tool plugs must match the outlet. Never modify the plug in

any way. Do not use any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching outlets will reduce

risk of electric shock.

2. Avoid body contact with earthed or grounded surfaces such as

pipes, radiators, ranges and refrigerators. It will increase the risk

of electric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords will increase

the risk of electric shock.

5. When operating a power tool outdoor, use a probably extension

cord suitable for outdoor use. Use a probably cord suitable for use

outdoor will reduce the risk of electric shock.

Personal safety

1. Stay alert, watch out what you are doing and use common sense

when operating a power tool. Do not use a power tool while you

are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in

2. Use personal protective equipment. Always wear eye protection.

Always use protective equipment such as duct mask, non-skid

safety shoes, hard hat, or heating protection for appropriate

conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to power source and/or battery

pack. picking up or carrying the tool. Carrying power tools with

your finger on the switch or energizing power tools that have the

switch on invites accidents.

4. Remove any adjusting key or wrench before turning on the power

tool. A wrench or key left attached part of the power tool may

result in personal injury.

5. Do not overreach. Keep proper footing and balance at all the

times. It will enable you got better control once power tool in

unexpected situations.

6. Dress properly. Do not wear loose clothing. Keep your hair,

clothing and gloves away from wroking parts. Loose clothes or

long hairs can be caught in working parts.

7. If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly

used. Use of these devices can reduce dust-related hazards.

Power tool use and care

1. Do not force the power tool. Use correctly the power tool for your

application. To use correctly the power tool will get the better

performance and more safety.

2. Do not use the power tool if the switch doesn’t work. Any power

tool cannot be controlled if switch is fault. If it is happened, please

contact the authorized service center.

3. Please disconnect the power source before adjusting, changing

accessories or storing power tools. It will prevent the risk of

starting the power tools accidentally.

4. Keep the power tools away from children and do not allow

persons who unfamiliar or without this instructions to operate the

power tool. Power tools are dangerous to untrained users.

5. Maintain power tools. Check for misalignment of binding of

6. Use the power tool, accessories and tool bits, etc., in accordance

with these instructions and in the manner intended for the

particular type of power tool, taking into account the working

conditions and the work to be performed. Use of the power tool for

operations different from intended could result in a hazardous

situation.

Service

Have your power tool serviced by a qualified repair person using

only identical replacement parts. This will ensure that the safety of

the power tool is maintained.

Specific warnings

Hold power tool by insulated gripping surfaces, when performing an

operation where the fastener may contact hidden wiring or its own

cord. Fasteners contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the operator an electric

shock.

IMPORTANT SAFETY

INSTRUCTIONS

Before charging, read all instructions and cautionary marks.

WARNING: Do not allow any liquid into charger; it may cause a

danger of electric shock.

1. Do not place any object cover the top of the charger as it could

cause overheating. Do not place the charger near any heat

source.

2. Pull on the charger to disconnect from the power source. Do

not pull on the lead only.

3. Never recharge a fully charged battery/tool. Overcharging will

shorten the battery life.

4. Make sure that the lead of charger is positioned where it will

5. Do not use an extension cord unless it is absolutely necessary.

To use an improper extension cord may cause the risk of fire,

electric shock or electrocution.

6. Do not use the charger if it has been subjected to a heavy

knock, dropped; otherwise damaged in any way. Take the

charger to an authorized service centre for a check or repair.

7. Do not charge with higher voltage than indicated as charger

specification; otherwise, the charger will burn up.

8. Do not disassemble the charger. Take it to an authorized

service center when it doesn’t work or other problem

happened. Incorrect re-assembly may result in the risk of fire,

electric shock or electrocution.

9. Suitable charging environment:

Charging temperature: 0°C ~40°C (32°F~104°F)

Discharging temperature: 0°C ~40°C (32°F~104°F)

Storage temperature: -20°C ~60°C (-4°F~140°F)

ADDITIONAL SAFETY WARNINGS

OF TOOL & CHARGER

1.This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

2.Children should be supervised to ensure that they do not play

with the appliance.

3.If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

CHARGING INSTRUCTIONS

Smart cellular phone Charger or

iPhone/iPad/iPod charger

Micro USB

USB

*Please use smart phone charger, power bank, iPhone/iPad/iPod

charger for charging the power tool.

*Please use our authorized USB cord for iPhone/iPad/iPod user.

*The charging indicator will be Red when in charging, the light will

be change to Green when fully charged.

WARNING: Please DO NOT use note book or computer to

charge the tool.

EXPLANATION OF GENERAL VIEW

Switch

(Forward/Reverse)

LED light

Drive (Collet)

1/4”(6.35mm)

Charging

indicator

SPECIFICATION

Rated no load speed 350 rpm

Output torque 3 Nm (31 kgf-cm/26.9 lbf-in)

Drive (Collet) 6.35mm (1/4") Hex insert chuck

Special function

Switch for forward or reverse

rotation.

Includes LED light.

LED charging indicator

Overall length: angled 140(L)x110(H) mm

Weight (w/Battery) 325 g

Battery type Li-ion

Battery voltage 3.6V

Battery capacity 1100 mAh

Charging time 1.5 hours (5V/2A)

Free running time 30 min

Bits set 5pcs 50mm driver bits:

6.0, #1, #2, 3.0, 4.0

Accessories Charging cord Micro USB cord

OPERATING INSTRUCTIONS

1. Attaching and removing accessories

allingInst

Installing the accessory (bit):

Insert the accessory shank to

the chuck.

Remove the accessory (bit):

Remove the accessory from

the chuck.

Remove

**Do not shake the tool or press

the trigger when installing or

remove the accessory.

**To avoid the tool damages, do not keep fastening or loosing the screw over

3 seconds when the tool is out of power or block.

** When the motor is stopped, please stop operation to avoid any damage.

**Do not recommend to use drill.

2. Switch (Forward / Reverse) & LED light

The switch features

Forward/Reverse function.

The LED will be light when

pressing the switch.

** Do not force the tool when

the tool is rotating.

Forward (R)

Reverse (L)

MAINTENANCE

CAUTION:

Always be sure that the tool is triggered off before inspection or

maintenance.

1. Inspecting screws of the tool

To make sure all of threads are fasten with correct way and tight

after disassembly or maintained the tool.

2. Maintenance of tool

Please clean up the tool regularly with dry wiper. Do not use oil,

gasoline, thinner, water, or other corrosiveness liquid, it may

damage the tool.

** Disconnect the plug from the power source and turn off the switch

before clean the tool.

3. Storage

Keep power tools out of the reach of children and humidity area.

4. Repair

Please contact with the authorized service center if problems cannot

be solved.

ACCESSORIES

CAUTION:

Always use authorized replacement parts and accessories. Never

use replacement parts or accessories which are not intended for use

with this tool. The use of any other attachment or accessory can be

dangerous and could cause injury or mechanical damage.

Cordless screwdriver

Micro USB/USB cord

Bits

PT-1362U USB 鋰電池充電起子組

產品使用說明書

重要安全須知

注意: 使用前，請仔細閱讀本使用說明書，在正確而安全的狀態下使

用，之後請妥善保管本使用說明書。

工作環境

1. 請保持工作環境整潔，髒亂或黑暗的工作環境會導致工作時危

險。

2. 請勿在容易起火、爆炸的場所附近使用; 例如，易燃的液體、氣

體或粉末。充電起子恐會產生火花而造成易燃物的燃燒。

3. 當使用充電起子時，請遠離孩童或旁觀者，以避免使用時不注

意、疲勞時而導致的危險。

電的安全

1. 充電起子的插頭需符合插座。請勿自行修改插頭！且不可使用插

座有接地線接頭，自行修改的插頭恐會造成危險或短路而起火。

2. 避免身體與有接地線或接地線表面物品接觸；例如，輸送管，散

熱器，爐灶和冰箱，以避免觸電，而導致危險。

3. 請勿在雨中、濕漉地、潮濕場所使用工具，水會進入充電起子而

導致短路、冒煙或燃燒。

4. 請勿拿著電線搬運充電器或以拉扯電線方式從插座拔下插頭。請

勿在火源、油、尖銳物品或會移動的物件附近使用，以免觸電、

冒煙或燃燒。

個人使用

1. 使用充電起子時，請保持警覺並注意，請勿在精神不濟、疲勞時、

服用藥物後或喝酒後使用，以避免造成個人或它人的危險或受

傷。

2. 請使用個人防護設備 (例如，口罩、安全鞋、安全帽、或防火衣

物..等) 並配戴安全眼鏡，以避免工作時造成個人受傷之疑慮。

3. 使用前，請務必注意開關是否已在關閉狀態，以避免在拿取時觸

碰開關，造成工具運轉。

4. 使用前，請確認金屬物品已離開工具，避免充電起子轉動時造成

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Pro's Kit

Pro's Kit

Pro's Kit SI-168U Manual de usuario

Pro's Kit

Pro's Kit SS-612A Manual de usuario

Pro's Kit

Pro's Kit PT-1210 Manual de usuario

Pro's Kit

Pro's Kit SI-137 Manual de usuario

Pro's Kit

Pro's Kit PT-0721 Manual de usuario

Pro's Kit

Pro's Kit Pro'sKt SS-621 Series Manual de usuario

Pro's Kit

Pro's Kit SI-B166 Manual de usuario

Pro's Kit

Pro's Kit PT-1207 Manual de usuario

Pro's Kit

Pro's Kit PT-1801 Manual de usuario

Pro's Kit

Pro's Kit SS-611 Manual de usuario

Pro's Kit

Pro's Kit PT-5208U Manual de usuario

Pro's Kit

Pro's Kit SS-615 Series Manual de usuario

Pro's Kit

Pro's Kit SS-611A Manual de usuario

Pro's Kit

Pro's Kit PT-1805 Manual de usuario

Pro's Kit

Pro's Kit SS-988 Manual de usuario

Pro's Kit

Pro's Kit PT-5501 Manual de usuario

Pro's Kit

Pro's Kit SI-168U Manual de usuario

Pro's Kit

Pro's Kit SS-979 Manual de usuario

Pro's Kit

Pro's Kit PT-1806 Manual de usuario

Pro's Kit

Pro's Kit SS-331B Manual de usuario

Pro's Kit

Pro's Kit GS-23K Manual de usuario

Pro's Kit

Pro's Kit SS-628 Series Manual de usuario

Pro's Kit

Pro's Kit HT-5501 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual