PRO Light LEDSOFT 18 Manual de usuario
USER MANUAL
LEDSOFT18
EN
FLEXIBLE LED SCREENS
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
REV.001-11/13
1
LEDSOFT18
TABLE OF CONTENTS 2
2
3
4
4
6
7
9
10
11
11
12
13
14
14
15
18
Safety
General instructions
Warnings and installation precautions
General information
1 Introduction
1. 1 Description
1. 2 Technical specications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
2. 2 How to combine several piece of screens
2. 3 How to adjust the distance between two screens
3 The connections
3. 1 To connect the power cable
3. 2 To connect the signal cable
3. 3 Set up and operation
4 Disassembly
4. 1 Disassembly procedure
5 Maintenance
5. 1 Cleaning and maintenance
5. 2 Trouble shooting
5. 3 Replacing a power adaptor
5. 4 Replacing LEDs
Warranty
LEDSOFT18
2
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualied electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the xture under the following conditions:
- in places subject to vibrations or bumps;
- in places with a temperature of over 50 °C.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Do not dismantle or modify the xture.
• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation denitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way dierent to the one described in this manual, it may suer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.
• The connection, installation and operation of LED screen should be processed as per instruction by
special person.
• Keep any inammable material at a safe distance from the unit.
• Install the unit in a well ventilated place.
• Never try to trample and tear the LED screen, keep the internal cable connection and electronic in order.
• Keep the hard or sharp article from lacerating the product.
• Prohibit sinking into the pouring water or other liquid.
• Handle with care when install and disassembly the LED screen to avoid the damage of the connecting
wire and other electronic component.
• The power cable should be connected to the power supply with ground.
• Prohibit connecting the power when LED screen was folded.
• Before nishing the installation, please do not connect the power.
• When there is wind, the display should be xed rmly with safe belt.
• When folding the LED screen, the surface of the curtain should be face to face.
• Please comply with the local relative regulations.
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
3
LEDSOFT18
GENERAL INFORMATION
Shipments and claims
The goods are sold “ex works” and always travel at the risk and danger of the distributor. Eventual dam-
age will have to be claimed to the freight forwarder. Any claim for broken packs will have to be forwarded
within 8 days from the reception of the goods.
Warranty and returns
The guarantee covers the xture in compliance with existing regulations. You can nd the full version of
the “General Guarantee Conditions” on our web site www.musiclights.it. Please remember to register the
piece of equipment soon after you purchase it, logging on www.musiclights.it. The product can be also
registered lling in and sending the form available on your guarantee certicate. For all purposes, the va-
lidity of the guarantee is endorsed solely on presentation of the guarantee certicate. Music & Lights will
verify the validity of the claim through examination of the defect in relation to proper use and the actual
validity of the guarantee. Music & Lights will eventually provide replacement or repair of the products de-
clining, however, any obligation of compensation for direct or indirect damage resulting from faultiness.
LEDSOFT18
4
- 1 - INTRODUCTION
1.1 DESCRIPTION
LEDSOFT series of exible LED screens is composed of a set of models having pitch value between 18mm
and 100mm, allowing advanced creative possibilities combined with simplied use and quick setup op-
erations.
LEDSOFT screens are conceived for projection of videos, images, backgrounds and texts, dierent models
are available with regards to viewing distance. Reduced mounting time and minimal required structures
are further advantages made possible by limited weight and volume.
All models are equipped with RGB 3-in-1 SMD LED sources, allowing an amazing light output (up to 3240
NIT for LEDSOFT18 featuring 18mm pitch value).
The modular concept and the simplied connection between modules enable build-up of large displays
in outdoor locations implying long viewing distances.
LEDSOFT screens are made in exible PVC, water-repellent and ame-resistant, ideal for design of geo-
metrical shapes (ie. corners, columns, circles) normally critical for conventional LED screens.
1.2 TECHNICAL SPECIFICATIONS
Applications
• For amazing set designs and events in indoor/outdoor locations
• In TV studios to have multiple viewing angles
• Touring and live events for real-time camera streaming
• Trade-show booths for creative video imaging
• In theme parks or public events
Mechanical features
• Module dimensions (WxH): 2.336x1.168mm
• Weight per square meter: 9.000g
• Flexible PVC, water-repellent and ame-retardant
• Cooling: natural airow
• Vertical hanging system: built-in belts and clips
• Indoor/Outdoor use (IP44)
Electrical features
• Power supply: AC 90/240V 50/60Hz
• Power in/out connections: RJ-45
• Average power consumption (per square meter): 32W
• Max power consumption (per square meter): 80W
• Working temperature: -10° / 50°
• Max ambience humidity: 10% - 90%
Video features
• LED source: hi-eciency SMD 3528 Tri-Color
• Pixel pitch: 18,25mm
• LED density: 3.002 LED/sqm
• Luminous ux: 3.240cd/sqm (NIT)
• Suggested viewing distance: 8m
• Pixel color depth: 36bit
• LED life span: >80.000h
5
LEDSOFT18
• Colours: >68,7 billions through RGB mixing
• Data refresh rate: >600Hz
• Colour calibration through PC software
• Maximum video IN signal resolution: 1024x768 pixel
• Viewing angle: 120° horizontal, 120° vertical
Control system
• Dedicated interface (Sender box) for video signal distribution and screen conguration
• Data IN sender box: DVI connector
• Data IN module: RJ45 connectors
• Connection between sender box and videowall: CAT5 data cable + RJ-45 connectors
Fig.1
LEDSOFT18
6
1.3 OPERATING ELEMENTS AND CONNECTIONS
AC 90-260V
DC 5V
To receiver
DC 5V
To receiver
Curtain
Button
LED lamp
AC 90-260V
Signal cable Protection clothing
Front view
Rear view
7
LEDSOFT18
- 2 - INSTALLATION
2.1 MOUNTING
LEDSOFT18 screen can be used by single or through combining to make a large LED screen, notice to
make the arrow up at the back of the display. Please install it according to the following step.
1. After receiving the LEDSOFT18 screen, take out to check whether the LEDSOFT18 screen is damaged,
whether all accessories is all ready. The accessories include supporting steel stick tube, hanging belt,
spare parts.
2. Unfold the LEDSOFT18 screen, insert supporting steel stick tube into the sheath at the top side of the
LEDSOFT18 screen and the loop of the hanging belt, several piece of steel tube can be connected
together by screw.
3. Hang the LEDSOFT18 screen on the truss with hanging belt, and fasten the hooks at the two end of the
hanging belt.
4. Use button around the LEDSOFT18 screen to make the nearby display connect together.
Fig.2
Supporting truss
Supporting stick
Hang belt
Hook
15C Signal cable
Button
Button
15C Signal cable
Fig.3
LEDSOFT18
8
Tabla de contenidos
Otros manuales de Iluminación del hogar de PRO Light
Manuales populares de Iluminación del hogar de otras marcas
JONATHAN Y
JONATHAN Y JYL5019A Manual de usuario
JONATHAN Y
JONATHAN Y JYL6007A Manual de usuario
Philips
Philips Ledino 31606/11/16 Manual de usuario
Salus
Salus UG600 Manual de usuario
Safavieh Lighting
Safavieh Lighting CANDRI TBL4427A Manual de usuario
Hunter
Hunter Bullet Spotlight Kit Manual de instrucciones
