Pro-Lift F1800A Manual de usuario

OWNER’S MANUAL

WORKING LOAD LIMIT 1800KG

• Safety Instructions

• Operation Procedures

• Maintenance Procedures

READ RULES FOR SAFE OPERATION

AND INSTRUCTIONS CAREFULLY

Model: F1800A

THIS JACK CONFORMS TO MANDATORY

STANDARD AS 2615:2016

Shinn Fu (Australia) PTY. LTD.

15 Viewtech Place, Rowville, Victoria 3178, Australia

FLOOR JACK

WARNING: THE JACK MUST BE USED ONLY ON HARD LEVEL

SURFACES AND BE FREE TO ROLL DURING LIFTING AND

LOWERING. DO NOT GET UNDER A VEHICLE THAT IS SUPPORTED

BY A TROLLEY JACK - USE THIS HYDRAULIC TROLLEY JACK

WITH SUITABLY RATED VEHICLE SUPPORT STANDS.

SAFETY INSTRUCTIONS

INSPECTIONS

1. BEFORE EACH USE

Visual inspection should be made before each use of the trolley jack for abnormal

conditions such as cracked welds, leaks and damaged, loose, or missing parts.

2. AFTER EACH USE

Trolley jack should be inspected immediately if the lift is believed to have been

subjected to an abnormal load or shock. It is recommended that inspection be made

by manufacturer’s or supplier’s authorised repair facility.

3. ANNUAL INSPECTION

Annual inspection of the trolley jack is recommended and is recommended to be

made by the manufacturer’s or supplier’s authorised repair facility to ensure that

your trolley jack is in optimum condition.

RECOMMENDATION FOR SAFE USAGE OF THE JACK

1. Consult the vehicle manufacturer’s manual prior to the lifting of the vehicle.

2. Conduct a pre-operational check of the equipment.

3. Use the hydraulic trolley jack for lifting and lowering only; the raised vehicle should

be supported on suitably rated vehicle support stands.

4. Use the hydraulic trolley jack on a hard level surface and ensure it is free to roll

during lifting and lowering.

5. No person should remain in a vehicle that is being lifted.

6. Chock the unlifted wheels of the vehicle.

7. Centrally locate the load on the head cap.

8. Support the vehicle on suitably rated vehicle support stands and remove the hydraulic

trolley jack prior to commencement of work on the vehicle.

9. No person should get bodily under a vehicle that is supported only by a hydraulic

trolley jack.

10. Make sure that lift point is stable and properly centered on jack saddle.

11. Vehicle should be clear of all passengers. Transmission should be in gear (or park

for automation transmission) and the emergency brake should be engaged.

12. Familiarize yourself thoroughly with this owner manual before operation to prevent

damage to jack and property, or personal injury.

Modications: Modications must not be carried out or accessories added.

SAFETY INSTRUCTIONS

CAUTION BEFORE USE

Due to shipment and/or handling air can be trapped in the hydraulic system, which can

interfere with the jacks lifting. To release air from the hydraulic system:

• Open release valve by turning the jack handle counterclockwise.

• Remove the oil ller plug from the cylinder.

• Rapidly pump jack handle through several full strokes.

• Replace the oil ller plug into the cylinder.

WARNING

DEATH OR

INJURY FROM

INCORRECT USE

USE TWO

SUPPORT

STANDS

FLAT HARD

LEVEL GROUND

FREE TO ROLL

DURING LIFTING

AND LOWERING

REFER TO VEHICLE MANUFACTURER’S

MANUAL FOR INSTRUCTIONS

OPERATION PROCEDURES

Before using

1. Remove bolted on cover plate and open

oil ller plug to allow air to be vented.

2. Open Release Valve with the handle.

Turn it counterclockwise.

3. Pump handle rapidly several times.

4. Close oil ller plug, then replace cover

plate.

5. No person should remain in the vehicle

that is being jacked.

Raising the jack

1. Place car in park, apply emergency

brake and chocked wheel in “straight

ahead” position.

2.Close Release Valve TIGHTLY (by

applying handle turning clockwise).

3. Position jack under load so that saddle

will contact load rmly and is centered

so it cannot slip. Avoid off-centered load

on the saddle.

4. Operate jack handle until saddle almost

approaches to contact with load. Once

again check to see that the saddle is

correctly positioned.

5. Raise load to desired height. Transfer

the load to Jack Stands immediately.

Lowering the jack

Open Release Valve VERY SLOWLY (by

applying handle turning counterclockwise)

and never more than 1/2 turns. When

Release Valve is opened, saddle will lower

easily due to spring tension on the Lift Arm

Assembly.

Moving the jack

Place handle in Handle Sleeve. DO NOT

move the jack when handle is on the

Release Valve as this may cause damage

to the pump unit of the jack. DO NOT move

the jack when it is under load.

CAUTION

Keep clear from the vehicle when

lowering the jack.

PARTS KEY

1. Oil Filler Plug

(Not shown, under Cover Plate)

2. Castor

3. Base

4. Release Valve

5. Pump Cylinder

6. Pump Piston

7. Handle Sleeve

8. Cover Plate

9. Plastic carry handle

10. Lifting Arm

11. Saddle

12. Link Rod

13. Front Wheel

14. Frame

15. Middle Spindle

16. Reservoir

(Not shown, under Cover Plate)

17. Handle

MAINTENANCE PROCEDURES

MAINTAINING OIL LEVEL

Important Note:

When adding or replacing oil, always

use a good grade Hydraulic Jack Oil (or

transmission oil, turbine oil etc.). Avoid

mixing types of oil. DO NOT use Brake

Fluid, Alcohol, Glycerine, Detergent, Motor

Oil or Dirty Oil. Improper uid can cause

serious internal damage to Jack.

ADDING OIL:

With saddle fully lowered & jack on level

ground, remove cover plate then open

Oil Filler Plug. Oil level should be approx.

12mm below valve hole. If low, add oil

as needed then close Oil Filler Plug and

replace cover plate.

REPLACING OIL:

For better performance and longevity,

replace oil supply once a year. To drain

oil, remove cover plate, open Oil Filler

Plug and loosen the Release Valve by

applying handle turning counterclockwise.

BE VERY CAREFUL not to permit dirt or

foreign matter to get into the system. Close

Oil Filler Plug and replace cover plate.

SPECIFICATIONS

Working Load Limit: .......................................................................................... 1800Kg

Jack Dimension : .............................................................. 550mm x 210mm x 140mm

Height Lowered : ...............................................................................................140mm

Height Raised : ................................................................................................. 381mm

Oil Capacity : ...................................................................................................95+/-5cc

Net Weight : .......................................................................................12.8Kg. (approx.)

210mm

550mm

65mm40mm

381mm

140mm

TROUBLESHOOTING

(USING JACK WITHIN RATED LOAD CAPACITY)

POSSIBLE JACK PROBLEMS

POSSIBLE CAUSES AND

SOLUTIONS

(Refer to Operation and

Maintenance procedures

for detailed information)

Release valve not tightly

closed.

To close or tighten, turn

release valve clockwise.

Air is in hydraulic system.

Release air from system.

Oil level is low in jack

Add oil as required

1. Oil reservoir is over-lled

Drain out some oil.

2. Lubrication of moving

parts is necessary.

Power unit is

malfunctioning.

Replace the power unit.

Jack will

not lift

load

Jack will

lift load,

but will

not hold

Jack will

not lower

completely

Poor jack

lifting.

Pump

feels

spongy

Jack will

not lift to

full height

Handle

raises by

itself when

jack is

under load

LUBRICATION

• Add lubrication oil to all moving parts

every 3 months.

PREVENTING RUST

• Check Piston Rod & Pump Piston

every 3 months for any signs of rust or

corrosion. Clean as needed and wipe

with an oily cloth.

• When not using the jack, always leave

the saddle & pump piston all the way

down.

KNOW YOUR JACK

Compare these illustrations with your

jack before operation and/or oil level

maintenance to become familiar with

the location of jack components.

RELEASE

VALVE

PUMP PISTON

DOWN

PROPER OIL

LEVEL

OIL FILLER

PLUG

PISTON ROD ALL

THE WAY IN

Tabla de contenidos

Otros manuales de Jacobo de Pro-Lift

Pro-Lift

Pro-Lift F-2332A Instrucciones de uso

Pro-Lift

Pro-Lift F2000 Manual de usuario

Pro-Lift

Pro-Lift PL3200 Instrucciones de uso

Pro-Lift

Pro-Lift G2000 Manual de usuario

Pro-Lift

Pro-Lift G-737 Instrucciones de uso

Pro-Lift

Pro-Lift F1350 Manual de usuario

Pro-Lift

Pro-Lift T-2501 Manual de usuario

Pro-Lift

Pro-Lift F1650A Manual de usuario

Pro-Lift

Pro-Lift F1800 Manual de usuario

Pro-Lift

Pro-Lift F-2332 Instrucciones de uso

Pro-Lift

Pro-Lift F1400 Manual de usuario

Pro-Lift

Pro-Lift G-4630 Instrucciones de uso

Pro-Lift

Pro-Lift PRO-A1200 Manual de usuario

Pro-Lift

Pro-Lift F-2330BMC Instrucciones de uso

Pro-Lift

Pro-Lift B-1850 Manual de usuario

Pro-Lift

Pro-Lift T-9446 Instrucciones de uso

Pro-Lift

Pro-Lift B-002D Instrucciones de uso

Pro-Lift

Pro-Lift F1650 Manual de usuario

Pro-Lift

Pro-Lift F-2525 Instrucciones de uso

Pro-Lift

Pro-Lift PL3300 Instrucciones de uso

Pro-Lift

Pro-Lift B-002NC Instrucciones de uso

Pro-Lift

Pro-Lift B-033D Instrucciones de uso

Pro-Lift

Pro-Lift PL1002 Manual de usuario

Pro-Lift

Pro-Lift G-4630JSC Instrucciones de uso

Manuales populares de Jacobo de otras marcas

Omega Lift Equipment

Omega Lift Equipment 18122C Instrucciones de uso

Pittsburgh

Pittsburgh 58816 Instrucciones de montaje

Unimec

Unimec TP Manual de usuario

Sonic

Sonic 4800703 Manual de usuario

BGS technic

BGS technic 70039 Manual de usuario

TradeQuip

TradeQuip 1128T Manual de usuario

VEVOR

VEVOR TJD-12000SP-F Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manual de usuario

Stels

Stels 51131 Manual de usuario

Bushranger

Bushranger RJX01 Manual de usuario

Clarke

Clarke CTJ2500QLG Manual de instalación y operación

Valex

Valex 1650520 Manual de usuario

Pfaff

Pfaff Merkur M0 Manual de usuario

Beta

Beta 3050/K Suplemento

Sealey

Sealey 1050CXHV Manual de usuario

Jung

Jung JH Series Manual de usuario

URIAH

URIAH UC200020 Manual de usuario

Kennedy

Kennedy KSJ010 Manual de usuario