PRO-KART 42822 Guía de referencia rápida

PEDAL CAR - GO CART

42822

ASSEMBLY & OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

Brought to You by Augusta Flint

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the

owner’s record below:

Model______________ Serial No.__________ Purchase Date_____________

SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire

manual to become familiar with the unit BEFORE you begin assembly.

Technical Specifications

Tool Name:Manual Pedal Car - Go Cart

Item Number: 42822

Wheel Base: 41-5/8"

Front Track: 30"

Rear Track: 30"

Ground Clearance at Pedal: 4-1/2”

Tire Size: 4.00-8" Pneumatic 30 PSI, Ball Bearing Mounted Hubs

Steering Wheel Size: 14-1/2"

Seat Height: 17-1/2"

Overall Dimensions: 58-1/4" x 36-1/8" x 30"

Handle Bar Width: 13"

Handle Bar Height: 34"

Construction: All Steel

Maximum Weight Capacity: 165 LBS.

Maximum Tire PSI: 30

Warning: The warnings, cautions and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must

be understood by the operator that COMMON SENSE AND CAUTION ARE

FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT, BUT

MUST BE SUPPLIED BY THE OPERATOR.

The Operator

PLEASE REMEMBER:

Do not operate the product if under the influence of alcohol or drugs. Read warning labels on prescriptions to

determine if your judgment/reflexes might be impaired.

Do not wear loose clothing or jewelry as they can be caught in moving parts.

Protective gloves and non-skid footwear are recommended.

Only one person on the Go Cart at a time. Do not exceed the 165 Lb. maximum weight capacity.

The Go Cart is for Off-Road use only.

Maintain caution when turning. Avoid excessively sharp turns.

Only drive the Pedal Car - Go Cart during daylight hours when natural light conditions are good. Do not

drive at night.

An approved safety helmet must be worn at all times.

Use only under adult supervision.

#42822 Page 2

Brought to You by Augusta Flint

Assembly

Your Pedal Car - Go Cart will require some minor assembly as indicated below. To assist you with assembly

and operation please refer to the Operational Figures and to the Assembly Diagram on page 5 and the

Parts List located on page 4.

Before assembling, remove any traces of the packing grease from the Go Cart and wipe all parts thoroughly

with a clean dry cloth. When cleaning do not use acetone, gasoline or paint thinner as these are dangerous to

you and may also cause damage to plastic and rubber parts.

Step 1) Attach the Front Handle Assembly (B) to the Main Body (A). Slide the two (2) main tubes on

the Main Body (B) into the Front Handle Assembly. Line up the holes and insert one Bolt (F)

down through each side. Slide on Washer (F) and tighten into place with one Nut onto each

Bolt.

Step 2) As necessary, attach the Handle Bar to the Front Handle Assembly (B) by lining up the holes

on the Handle Bar with the holes on the round plate at the uppermost end of the Front Handle

Assembly. Insert Bolts through the Handle Bar and round plate. Slide on Washers and

tighten into place with Nuts (F)-see Figure 1.

Step 3) Slide each of the two front Wheels (D) onto the Axle. Slide on a Washer and screw in

Bolt (E).

Step 4) Slide a Washer (E) onto each of the rear axles. Slide on the Wheels (D) and then slide on

another Washer for each Wheel (D) and Axle. Insert Bolt and tighten into place.

Step 5) The position of the seat can be placed forward or to the back

of the Frame. The Seat (C) has a post at the bottom. Insert

the post into one of the square holes in the rear of the Go-Cart.

Set the Seat according to the needs of the driver - see Figure 2.

Insert Bolts

Figure 1

Figure 2-Inserting Seat Post

Insert Seat Post

#42822 Page 3

Brought to You by Augusta Flint

Operation

Prior to operation of your Pedal Car - Go Cart make certain to apply oil to any moving parts. Oil should be

applied to the Wheel Bushings, the Axles, and down into the Steering Column.

The Pedal Car - Go Cart is moved forward or in reverse by pushing on the pedals. To slow down and stop the

Go-Cart, pull up on the Brake Lever. It will push against the Wheel causing it to slow down and stop-see

Figure 3.

Warning: Maintain a low speed for safety.

Warning: Maintain caution when turning and avoid exceedingly sharp turns. Sharp turns

may cause the Go-Cart to tip over, resulting in serious harm to the rider and possibly damaging the Go-Cart.

After Operation-Maintenance

Lubrication: For average use, lubricate regularly. Lubricate more frequently with increase in use.

STORAGE: Store in a dry place to avoid rust and corrosion.

IF THERE IS ANY QUESTION ABOUT ACONDITION BEING SAFE OR UNSAFE, DO NOT OPERATE THE PEDAL CAR - GO-CART.

Unpacking

UNPACK AND CHECK CONTENTS

When unpacking your Manual Pedal Car Go-Cart, check to make sure the following parts are included. If any

parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.

Part # Description Quantity Part # Description Quantity

A Main Body 1 D Wheel 4

B Front Handle Assembly 1 E Assembling Hardware 1

C Seat 1 F Assembling Hardware 1

G Sprocket Assembly 1

(includes: sprocket, bearing, shaft and seal)

Brake

Figure 3

#42822 REV 11/04 Page 4

Brought to You by Augusta Flint

#42822 Page 5

Assembly Diagram - Manual Pedal Car - Go Cart

PLEASE READTHE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS

A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY

REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE

ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE

PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS

AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS

AND NOT BY THE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER

REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR

HER INSTALLATION OF REPLACEMENT PARTS THERETO

Note: Someparts arelistedandshown forillustrationpurposes only andarenot availableindividuallyas

replacementparts.

REV 11/04

Brought to You by Augusta Flint

Tabla de contenidos

Manuales populares de Carrito para exteriores de otras marcas

Costway

Costway TH10057 Manual de usuario

Vivo

Vivo CART-PC02S Manual de usuario

Ergotron

Ergotron STYLEVIEW SV42-3162-1 Manual de usuario

VEVOR

VEVOR SC01 Manual de usuario

Carts Vermont

Carts Vermont 20 Manual de usuario

Vivo

Vivo CART-PC01 Manual de usuario

Costway

Costway TL0400 Manual de usuario

XPOtool

XPOtool 30261 Manual de usuario

Branick

Branick 130 Manual de uso y cuidado

Anthro

Anthro PrinterCart Manual de usuario

Westward

Westward 2CZY4 Manual de servicio

Hupfer

Hupfer TTW/V Manual de usuario

Gorilla Carts

Gorilla Carts GCR-10P Manual de usuario

Numatic

Numatic EcoMatic EM-5 Manual de usuario

Bosch

Bosch XL-Cart Instrucciones de montaje

Tennsco

Tennsco Modular Cart Top Component Assembly Manual de instrucciones

Makita

Makita DCU601 Manual de usuario

Clam

Clam POLAR TRAILER HD MAX Manual de usuario