Pro Dunk Hoops Goal Light LED Manual de usuario

Pro Dunk® Goal Light

Lighting System

Thank you for purchasing our Goal Light. We try hard to ensure that our products

are of high quality and free of manufacturing defects and of missing parts. How-

ever, if you have any problems with your Goal Light, such as a manufacturing

defect or a missing part please contact us at the following:

Toll Free: 1.888.600.8545 Pro Dunk® Hoops

Web: www.produnkhoops.com 22047 Lutheran Church Rd.

FAX: (281) 357-4822 Tomball, TX 77377

Support: www.produnkhoops.com/support

Read this manual all the way through before starting

assembly of your Goal Light. Then read each step

completely before beginning installation.

OWNER’S MANUAL

Ref. Qty. Description

A 1 3 Piece Pole System (with pre-assembled power cable)

B 1 Main Pole System Support Arm

C 1 Light Assembly (pre-assembled)

D 2 Halogen Light Bulbs

E 2 Wire Light Guards

F 1 Main Pole Mount Bracket

G 4 10mm x 3cm Hex Bolts

H 1 10mm x 7cm Hex Bolt

I 6 10mm x 2.5cm Hex Bolt

J 8 10mm Flat Washer

K 7 10mm Lock Washer

L 1 10mm Hex Nut

Bill Of Materials

Safety Instructions

 All tools used to assemble this product

should be used in compliance with manu-

facturer’s guidelines.

 Installation of this product will require

heavy lifting and bending. Any person that

is not capable of such activity should not

participate in the installation of this product.

 If using a ladder during assemble, use ex-

treme caution and refer to the warnings

and cautions on the ladder.

 Due to the size and weight of this product,

we recommend at least (4) capable adults

are present.

 Make sure there are no overhead power

lines within a 35 foot radius of the basket-

ball system.

 All parts and components necessary to

complete proper installation are included

within this product. Do not use parts not

included with our system. Failure to follow

this requirement could cause product mal-

function and will void warranty of this prod-

uct.

 Keep all organic materials away from parts

and components to avoid corrosion.

 Never use your Goal Light during rain or

snow

 Make sure your lamps are completely dry

before plugging in your Goal Light.

 Only use a power source that is 110-120v

that can supply 1,500 WATTS of continu-

ous power.

IMPORTANT

It is the responsibility of purchaser to ensure that

all installers and players fully comply with the de-

tailed instructions set forth in this product installa-

tion manual. Product assembly should be carried

out exactly as instructed and owner supervision

of use and installation is required to prevent risk

of product malfunction or risk injury.

Pro Dunk® Hoops retains the right to

modify this document at any time without

notice or obligation.

Keep this installation manual as a refer-

ence for your safety and the safety of

those playing on the basketball system.

Additional copies of these safety instruc-

tions are available by calling customer

service at 1-888.600.8545 or at

www.produnkhoops.com/support

 Check the Goal Light System on a regular ba-

sis to ensure that there are no signs of dete-

rioration or corrosion, loose hardware, or

damaged parts. If you see any signs of dam-

age contact Pro Dunk® Hoops for replace-

ment parts or assistance.

 For maintenance repairs please contact a pro-

fessional. produnkhoops.com/installers

 Failure to follow these safety instructions

could result in product malfunction, seri-

ous injury, or even death.

Installation Overview

In order to have safe fun and a long use of your Goal Light, please note and

heed the following:

1) Prior to Goal Light assembly, check for power lines within 35 feet

of your basketball system. If power lines are within 35 feet of

your basketball system do not install the Goal Light System.

2) Immediately unpack all components and cross check against bill

of materials. Report any shortages to Pro Dunk® Hoops cus-

tomer service at 1.888.600.8545.

3) You must have a Pro Dunk® basketball system with the new 4

threaded mounting holes on the top of the main pole. You may

have to remove 4 plugs to expose these threaded holes.

4) For safety measures, have at least 4 capable persons to assist

you in assembly of your Pro Dunk® Goal Light.

5) Parts can be ordered at www.produnkhoops.com/parts

Required Tools

 (2) Crescent Wrenches

 (3-4) 8ft ladders

 (1) Phillips Screw Driver  17mm

Bolt/Nut Sizes

Socket/Wrench Sizes Recommended

Assembly

1) Bulb Assembly

WARNING—Be very carful not to touch the Halogen Light Bulbs (D) with your hands.

Using a phillips screwdriver, remove the screw on the top of the front face of the Light Assem-

bly (C). Then remove the glass cover and insert the Halogen Light Bulb (D) into to Light As-

sembly (C). Repeat this for the second Light Assembly (C). Be very carful not to touch the

Halogen Light Bulbs (D) with your hands. Use a clean rag or paper towel to handle the Halo-

gen Light Bulbs (D).

2) Assemble Wire Light Guards

Using a small Philips screwdriver remove the screw located on the front face of the Light As-

sembly (C). Be careful to not lose the small screws.

Place the Wire Light Guard (E) where all 4 tabs are installed between the lamp frame and

glass. Line the metal tab up with the Light Assembly (C) screw hole. Then screw the light

housing screw back into the Light Assembly (C) locking the Wire Light Guard (E) in place.

Repeat this step for the second light housing (C).

3) Assemble Pole System

Find a large area to assemble the 3 Piece Pole System (A) and Main Pole System Support Arm

(B). Slide the 3 Piece Pole System (A) together and locate the 2 threaded holes that are used to

secure the 3 Piece Pole System (A) together. Using 2 10mm x 3cm Hex Bolts (G) secure the 3

Piece Pole System (A) together.

Locate the 2 threaded holes that are used to secure the Main Pole System Support Arm (B) to

the 3 Piece Pole System (A). Using 2 10mm x 2.5cm Hex Bolts (G), 2 10mm Flat Washers (J),

and 2 10mm Lock Washers (K) to secure the Main Pole System Support Arm (B) to the 3 Piece

Pole System (A).

4) Plug Lamp Assembly into Pole Assembly

Connect the waterproof connector on the Lamp Assembly (C) to the waterproof connector on

the 3 Piece Pole System (A). Line up connectors and push firmly together to create a good

connection. Twist the screw connector to create a water resistant seal.

5) Check Lights

WARNING—Be very carful not to touch the Halogen Light Bulbs (D) with your hands.

Double check to make sure your Light Assembly (C) is working properly. Using an outdoor

rated extension cord plug your Goal Light into a power source. Ensure that the Light Assem-

bly (C) lights up. If they do not, unplug Goal Light from power and allow the lamps to cool

and adjust the light bulb inside as it might not have a good connection. Repeat step 5 until

both Halogen Light Bulbs (D) light up.

6) Attach Main Pole Mount Bracket (F) to Pro Dunk® Main Pole

Using 4 Hex Bolt 10mm x 2.5cm (I), 4 10mm Lock Washers (K), and 4 10mm Flat Washers

(J) to attach the Main Pole Mount Bracket (F) to your Pro Dunk® Main Pole.

Otros manuales para Goal Light LED

Tabla de contenidos

Manuales populares de Iluminación de paisajes de otras marcas

Intex

Intex SL1006 Manual de usuario

LED Group

LED Group ROBUS R2IN13W Manual de usuario

Patriot Lighting

Patriot Lighting 343-1484 Manual de usuario

Hess

Hess SERA G: SERA S Manual de usuario

LIGMAN

LIGMAN JET 44 Manual de usuario

LIGMAN

LIGMAN MALTA 1 Manual de usuario

Cooper Lighting

Cooper Lighting MCGRAW-EDISON WBG Manual de usuario

Cooper Lighting

Cooper Lighting Invue 42 - 175W Manual de usuario

Saxby Lighting

Saxby Lighting Islay 68784 Manual

LIGMAN

LIGMAN EU-10016-3 Manual de usuario

Cooper Lighting

Cooper Lighting McGraw-Edison ZD Credenza Manual de usuario

LIGMAN

LIGMAN KI-60475 Manual de usuario

Cooper Lighting

Cooper Lighting Generation CLB25MWW5C373 Manual de usuario

Malibu Boats

Malibu Boats CL905K Manual de usuario

LIGMAN

LIGMAN NYB-30161 Manual de usuario

LIGMAN

LIGMAN SI-80021 Manual de usuario

Volt

Volt 2-in-1 Tiki-Brass Torch Light Manual de usuario

Malibu Boats

Malibu Boats CM110P Manual de usuario