Pro Dunk Hoops Bear Manual de usuario

Patten Pending Number 62433850 1

OWNER’S

MANUAL

Warning

 ! Do not slide, climb, or

play on pole.

 ! Keep organic material

away from base. Grass,

litter, etc. could cause

corrosion and /or dete-

rioration.

 ! Check system twice a

year for signs of corro-

sion (rust, pitting, and

chipping). Remove rust

and/or loose paint com-

pletely and repaint with

exterior enamel paint. If

rust has penetrated

through the steel any-

where, replace immedi-

ately.

 ! Check unit before

each use for loose

hardware, excessive

wear, and signs of cor-

rosion and repair be-

fore using.

 ! During play, use ex-

treme caution to keep

players face away from

the backboard, rim, and

net.

 ! Wear a mouth guard

when playing to avoid

dental injuries.

 ! When adjusting

height, keep hands and

fingers away from mov-

ing parts.

 ! During play, do not

wear jewelry (rings,

watches, necklaces,

etc.). Objects may en-

tangle in net.

Bear™

Basketball System

WELCOME TO THE FAMILY OF

BEAR™ OWNERS

Thank you for purchasing our basketball system. We try hard to ensure that our

products are of high quality and free of manufacturing defects and of missing

parts. However, if you have any problems with your basketball pole, such as a

manufacturing defect or a missing part please contact us at the following:

Toll Free: 1.888.600.8545 Pro Dunk® Hoops

Web: www.produnkhoops.com 22047 Lutheran Church Rd.

FAX: (281) 357-4822 Tomball, TX 77377

Please provide model number, serial number, and/or part number of the product

and/or part when you call, write or email. These numbers can be found on the

product, packaging, or on the back of the main pole.

Purchase Parts: www.produnkhoops.com/parts

Support: www.produnkhoops.com/support

Installation Video: https://www.produnkhoops.com/video/bear_assembly.html

Read this manual all the way through before starting to

put up your system. Then read each step completely

before beginning installation.

Patten Pending Number 62433850 2

Ref. Qty. Description

A 1 Vertical Post

B 1 Base

C 1 Main Extension Arm

D 1 Backboard Assembly

E 2 Upper Parallel Linkage Arm

F 1 Weight Box Cover

G 1 Weight Box Back Wall

H 1 Weight Box Front Wall

I 2 Weight Box Side Wall

J 4 Leveler Feet

K 1 Weight Divider

L 2 Turf Wheel

M 2 Main Pole Support Brace

N 2 Weight Box Lock

O 1 Pole Pad Bottom

P 1 Pole Pad Top

Q 1 Height Adjustment Actuator

R 1 Spring Assist

S 1 Safety Pin

T 1 Safety Pin Locking Pin

U 1 Rim Height Sticker

V 1 Rim Height Indicator Meter

W 2 Ground Anchor Assembly

X 4 Concrete Anchor Assembly

Y 4 16mm x 33cm Hex Bolt

Z 2 14mm x 13cm Hex Bolt

AA 2 16mm x 30cm Hex Bolt

BB 10 16mm Locking Hex Nut (4 are used for Main Pole Mounting)

CC 2 14mm Locking Hex Nut

DD 4 16mm x 6cm Hex Bolt (Main Pole Mounting)

EE 8 16mm Flat Washer (Main Pole Mounting)

FF 4 16mm Lock Washer (Main Pole Mounting)

GG 4 12mm x 4.5cm Hex Bolt (Main Pole Support Assembly)

HH 8 12mm Flat Washer (Main Pole Support Assembly)

II 4 12mm Lock Washer (Main Pole Support Assembly)

JJ 4 12mm Hex Nut (Main Pole Support Assembly)

KK 4 Rim Spacers

Bill Of Materials

Patten Pending Number 62433850 3

Ref. Qty. Description

LL 1 Axle

MM 2 Hex Nut (Axle Assembly)

NN 2 Axle Spacer

PP 10 6mm x 1.5cm Allen Bolts (Weight Box Assembly)

QQ 8 6mm Hex Nuts (Weight Box Assembly)

RR 2 Cotter Pin (Axle Assembly)

SS 8 8mm x 3cm Hex Bolt (Padding Assembly)

TT 8 8mm Flat Washer (Padding Assembly)

UU 8 8mm Lock Washer (Padding Assembly)

VV 8 10mm x 4cm Hex Bolt (Front Leveler Assembly)

WW 16 10mm Flat Washer (Front Leveler Assembly)

XX 8 10mm Lock Washer (Front Leveler Assembly)

YY 8 10mm Hex Nut (Front Leveler Assembly)

ZZ 4 12mm x 11cm Hex Bolt (Back Leveler Assembly)

AAA 8 12mm Flat Washer (Back Leveler Assembly)

BBB 4 12mm Locking Hex Nut (Back Leveler Assembly)

CCC 4 14mm x 9cm Hex Bolt (Leveler Feet Assembly)

DDD 8 14mm Flat Washer (Leveler Feet Assembly)

EEE 4 14mm Locking Hex Nut (Leveler Feet Assembly)

FFF 2 Front Leveler

GGG 2 Back Leveler

HHH 1 Rim

III 4 10mm x 7cm Hex Bolt (Rim Assembly)

JJJ 8 10mm Flat Washers (Rim Assembly)

KKK 4 10mm Lock Washers (Rim Assembly)

LLL 4 10mm Hex Nut (Rim Assembly)

MMM 4 Rim Shim Washers (optional)

NNN 1 Rim Cover Plate (Rim Assembly)

OOO 2 Rim Cover Plate Screws (Rim Assembly)

PPP 2 12mm x 12cm Hex Bolt (Back Wheel Assembly)

QQQ 4 12mm Flat Washer (Back Wheel Assembly)

RRR 4 Steel Spacer (Back Wheel Assembly)

SSS 2 12mm Lock Hex Nut (Back Wheel Assembly)

TTT 2 Back Wheels (Back Wheel Assembly)

Patten Pending Number 62433850 4

Patten Pending Number 62433850 5

Hardware Diagrams

Tear this page out for reference during assembly

Patten Pending Number 62433850 6

Safety Instructions

 All tools used to assemble this product

should be used in compliance with manu-

facturer’s guidelines.

 Installation of this product will require

heavy lifting and bending. Any person that

is not capable of such activity should not

participate in the installation of this product.

 If using a ladder during assemble, use ex-

treme caution and refer to the warnings

and cautions on the ladder.

 Due to the size and weight of this product,

we recommend at least (4) competent

adults are present.

 Before anchoring the weight box please

call 811 to ensure that all underground utili-

ties are a safe distance away from the an-

chor system.

 Make sure there are no overhead power

lines within a 25 foot radius of the basket-

ball system.

 All parts and components necessary to

complete proper installation are included

within this product. Do not use parts not

included with our system. Failure to follow

this requirement could cause product mal-

function and will void warranty of this prod-

uct.

 Keep all organic materials away from parts

and components to avoid corrosion.

 Please use caution when performing Slam

Dunks on your Pro Dunk® system.

 Do not climb on any part of the basketball

system as it was not intended for this activ-

ity.

IMPORTANT

It is the responsibility of purchaser to ensure that

all installers and players fully comply with the de-

tailed instructions set forth in this product installa-

tion manual. Product assembly should be carried

out exactly as instructed and owner supervision

of use and installation is required to prevent risk

of product malfunction or risk injury.

Pro Dunk® Hoops retains the right to

modify this document at any time without

notice or obligation.

Keep this installation manual as a refer-

ence for your safety and the safety of

those playing on the basketball system.

Additional copies of these safety instruc-

tions are available by calling customer

service at 1.888.600.8545 or at

www.produnkhoops.com/support

 Do not use the basketball system as a lift or to

hoist anything.

 Players should wear protective mouth guard

during play to avoid any time of dental injury.

 Players should refrain from wearing any jew-

elry that could potentially get caught in the rim

or net.

 Do not hang on the rim or system at any

point.

 Do not allow children to adjust basketball sys-

tem.

 Check the basketball system on a regular ba-

sis to ensure that there are no signs of dete-

rioration or corrosion, loose hardware, or

damaged parts. If you see any signs of dam-

age perform maintenance or contact Pro

Dunk® Hoops for replacement.

 For maintenance repairs please contact a pro-

fessional.

 Do not dunk on the system without all 30 con-

crete blocks and the back jack anchored se-

curely to the surface.

 Failure to follow these safety instructions

could result in product malfunction, seri-

ous injury, or even death.

Patten Pending Number 62433850 7

Installation Overview

In order to have the safest, fun and longest use of your Pro Dunk® system,

please note and heed the following:

1) Immediately unpack all components and cross check against bill

of materials. Report any shortages to Hoops Inc. customer ser-

vice at 1.888.600.8545.

2) Parts can be ordered at www.produnkhoops.com/parts

4) For safety measures, have at least 4 capable persons to assist

you in assembly of your Pro Dunk® Goal.

5) Have 30 solid concrete blocks (Common: 4x8x16 inch) on hand

for the ballast. Blocks are not included.

Patten Pending Number 62433850 8

Required Tools and Materials

 30 Solid Concrete Blocks (Common: 4x8x16 inch)

(Actual: 3.625x7.625x15.625 inch)

 Level

 Tape Measure

 Box Cutter

 (2) Large Crescent Wrenches

 (1) 4mm Allen Key

 Gloves

 Pencil

 24mm

 22mm

 19mm

 17mm

 13mm

 10mm

Bolt/Nut Sizes

Socket/Wrench Sizes Recommended

4x8x16 inch Solid Cap Concrete Block

Patten Pending Number 62433850 9

Storing Your Bear

Patten Pending Number 62433850 10

Assembly Video

https://www.produnkhoops.com/video/bear_assembly.html

Installation of a Pro Dunk® Bear basketball goal system by experienced professional

assembly crew. It shows the entire assembly process from start to finish and in-

cludes tips and explanation by the experts at www.produnkhoops.com.

https://www.produnkhoops.com/video/bear_assembly.html

Navigate to be below URL to watch our installation video.

Tabla de contenidos

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario