PRISMJET 54 Gen2 Manual de usuario
PrismJET 54 Gen2 OPERATION MANUAL Safety instructions
13
1 Safety instructions
This chapter explains warning terms, safety precautions and warning labels on the product that operators
and people who install this product need to know.
WARNING
• When installing and operating this printer, be sure to follow the directions and
warnings in this book.
Safety instructions PrismJET 54 Gen2 OPERATION MANUAL
14 1.1 Types and meanings of warnings
1.1 Types and meanings of warnings
The warnings in the Operation Manual and the warning labels attached to the printer are categorized into
three stages.
Understand the meanings of the following warning terms and follow the contents (instructions) in this
manual.
Warning Meaning
Used for dangerous situations where death or serious injury may be caused.
Used for dangerous situations that may cause slight or medium injury, or when all or
parts of products are damaged.
Used for special cautions and for information that needs to be emphasized.
WARNING
CAUTION
NOTE
PrismJET 54 Gen2 OPERATION MANUAL Safety instructions
1.2 Important safety instructions 15
1.2 Important safety instructions
This section explains general cautions that must be followed in order to use this printer safely.
Do not install this printer in the following places.
It may cause an injury if the printer falls down.
• On a shaky stand
• Slanting location
• Places where vibration of other machines etc. is transmitted
Do not step on this printer or place heavy things on top of it.
It may cause an injury if the printer falls down.
Do not block the vent on the product with cloth or other material.
If you cover the vent, the product interior may get hot and cause a fire.
Do not install the printer where it is humid or dusty.
It could lead to an electric shock and fire.
Do not use a damaged power cable.
It could lead to an electric shock and fire.
Do not pull out or insert the power plug with a wet hand.
This could lead to an electric shock.
Do not connect an earth wire to the following places.
•Gas pipes
There is a possibility of ignition and explosion.
• Earth wire of telephone cables and lightning rods
Heavy current might flow whenever lightning strikes.
• Water pipe and faucet
The earth might not work if a plastic pipe is connected in the middle of the metal pipe.
Do not insert or drop metal or flammable objects into the printer through openings such as a vent.
It could lead to an electric shock or fire.
Do not spill flammable liquid on the platen.
This could lead to a fire.
Do not place any combustible materials on the platen while the heater is working.
There may be a risk of fire.
If foreign substances or liquids such as water entered the printer, do not use the printer as it is.
It could lead to an electric shock or fire.
Immediately turn OFF the power switch, disconnect the power plug from the electric socket, and contact
SIGNWarehouse Product Support or your PrismJET Dealer.
Wire the various cords as directed in the Operation Manual.
Mistaken wiring could cause fire.
Be sure to use the specified power cable.
Using power cables other than the specified can cause an electric shock or fire.
WARNING
Safety instructions PrismJET 54 Gen2 OPERATION MANUAL
16 1.2 Important safety instructions
Make sure to use only the specified power supply (AC 100 V to 120 V or AC 200 V to 240 V).
If a power supply other than the specified voltage is used, it could cause an electric shock and fire.
Take power for the printer directly from the power socket (AC 100 V to 120 V or AC 200 V to 240 V).
Do not use multiple plugs on the same socket. This could generate heat and might cause fire.
Be sure to use a dedicated power socket with earth wire for the power supply, and connect it to the earth wire.
If the earth wire is not connected, an electric shock or fire may occur.
The waste fluid from the printer falls under the category of waste oil (waste ink) of industrial waste (out of the 19
items of general waste from business activities). You are obligated to properly dispose of waste fluid in compliance
with Wastes Disposal and Public Cleansing Act and local ordinances. Delegate disposal to an industrial waste
disposal contractor.
Pay attention to the following points when handling power cable.
• Do not tamper with the power cable.
• Do not put heavy objects on the power cable.
• Do not bend, twist or pull the power cable by force.
• Do not route the power cable near heating appliances.
Pay attention to the following points when handling the power supply plug.
Any mishandling of the power cable could cause a fire.
• Make sure that no foreign substances such as dust etc. are stuck to the power plug.
• Make sure that the power plug is firmly inserted to the edge of the power socket.
Wear protective equipment (gloves, goggles or eye protection, protective mask, protective clothing) when
handling ink.
Be cautious that ink does not get into your eye or make a contact with your skin.
• When ink gets into your eye or make a contact with your skin, wash with water immediately.
• If left as it is, it may cause red eye or light inflammation. If it is necessary, please see your doctor immediately.
Do not disassemble ink cartridges.
If disassembled, there is a possibility that ink might come into contact with eyes or skin.
Do not operate the media loading lever during the initial operation or printing.
The print head portion may touch the pressurizing roller portion, and cause a malfunction.
Do not use volatile solvents such as thinner, benzene, or alcohol.
These solvents could cause damage to the paint.
Do not touch the media guide while printing.
The media guide becomes very hot and you could burn yourself.
Do not touch the media feed slot, platen, and media guide while the heater is working.
The media feed slot, platen, and media guide become very hot and you could burn yourself.
Be careful that no moisture enters the printer.
There is a possibility that the electric circuit inside the printer is short circuited.
Do not open covers attached using screws under any circumstances.
This may cause an electric shock or a malfunction.
CAUTION
PrismJET 54 Gen2 OPERATION MANUAL Safety instructions
1.2 Important safety instructions 17
When cleaning the cleaning wiper,
• Do not touch the cleaning wiper and head cap unit.
Head cleaning may not be performed correctly because of oil from your hands.
• Make sure to wipe the print head using the cleaning stick.
A wet cleaning stick may cause the print head to clog.
• Do not reuse the cleaning stick.
The attached dust, etc may damage the print head.
When cleaning around the capping unit,
• Use a dry cleaning stick. A damp stick can cause damage to the print head.
• Do not touch the tip of a cleaning stick with fingers. Skin oil will damage the print head.
• Do not reuse a cleaning stick. Dust on the stick will damage the print head.
When cleaning around the print head,
• Do not touch the nozzles of the print head.
Doing so may damage the print head.
• Do not touch the tip of the cleaning stick.
The print head may be damaged because of oil from your hands.
• Never put water, etc on the tip of the cleaning stick.
Doing so may damage the print head.
• Do not reuse the cleaning stick.
The attached dust, etc may damage the print head.
When cleaning the color sensor,
• Do not touch the nozzles of the print head.
Doing so may damage the print head.
• Do not touch the tip of the cleaning stick.
The print head may be damaged because of oil from your hands.
• Never put water, etc on the tip of the cleaning stick.
Doing so may damage the print head.
• Do not reuse the cleaning stick.
The attached dust, etc may damage the print head.
• Do not push the glass on the color sensor too hard with a cleaning stick. This will damage the glass.
Do not slant the printer, prop it against a wall or turn it upside down.
There is a possibility that ink inside the printer may leak.
Moreover, normal operation after shifting (to these positions) cannot be guaranteed.
Unpacking or moving this printer must be done by the following number of people.
• More than three persons
Installing the dedicated stands on the printer must be done by the following number of people.
• More than three persons
When installing the dedicated stands, make sure to turn OFF the printer and unplug the power cable.
There may be a risk of electric shock.
When you do not use the printer for a long period, make sure to pull out the power plug from the power socket for
safety.
Make sure to connect an earth wire to the earth connection that meets the following standards.
• Earth terminal of power socket
• Earth wire with copper plate which is buried at 650 mm or more, deep in the ground.
Before operation, make sure to read the Safety Data Sheet (SDS).
Ventilate the workplace.
Not doing so may make you feel sick or may lead to a fire.
Safety instructions PrismJET 54 Gen2 OPERATION MANUAL
18 1.2 Important safety instructions
Right after printing, the media guide becomes very hot.
Allow the media guide to cool down before the next operation.
When loading the roll media, place it on a flat surface such as a desk.
If the roll media is loaded with the scroller up, the scroller may be damaged.
Pay attention to the following points when cutting roll media.
Mishandling the razor blade may cause a cut on your finger or hand.
• When you hold media, do not place your finger on the media cut groove.
• Move the razor blade along the media cut groove.
When cleaning the areas other than the wiper, make sure to turn OFF the power and unplug the power cable.
Move the printer maintaining a horizontal position.
This equipment is not suitable for use in locations where children are likely to be present.
PrismJET 54 Gen2 OPERATION MANUAL Safety instructions
1.3 Warning labels 19
1.3 Warning labels
This section explains the handling of warning label, pasting location and types.
Warning labels are attached to parts of the printer that need special caution.
Understand the locations and the descriptions of the danger associated with each label before operating
the printer.
1.3.1 Handling the warning labels
When handling the warning labels, be careful about the following points.
NOTE
• Check whether all the warning labels can be read.
If the letters or illustrations on the label are not clear, remove the dirt from the label.
• Use cloth, water and mild detergent for removing dirt from the warning label.
Avoid either organic solvents or gasoline.
• It is necessary to replace the labels if they are damaged, lost or illegible.
If the warning labels have to be replaced, contact your local PrismJET Dealer.
1.3.2 Location and type of warning labels
Pasting locations of the warning labels are shown in the following figure.
(1) Front
1
2
33
2
Safety instructions PrismJET 54 Gen2 OPERATION MANUAL
20 1.3 Warning labels
(2) Rear
No. Types of warning labels
1
2 Hot Surface Caution Label
The surface may get hot and may cause burn injury.
Do not touch with your hand for at least 30 minutes after turning off the printer.
3 Pinch hazard.
Keep hands and fingers clear of covers while opening or closing.
4
”~” on the rating plate represents AC voltage.
2
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
