Pride Mobility GT Manual de usuario

Serial #

Dealer:

Address:

Telephone:

Purchase Date:

Please ﬁll out the following information for quick reference:

OWNER’S MANUAL

Manufactured by Jiangxi Jiangte, distributed by Pride Mobility.

WARNING! Read the owner’s manual before operating

this scooter.

Manufactured By:

Jiangxi Jiangte Electric Vehicle Co., Ltd.

No.139,Yishang Avenue,

Economic Development Zone, Yichun,

Jiangxi 336000

Distributed By:

Pride Mobility Products Pty. Ltd.

20-24 Apollo Drive

Hallam, VIC 3803

AUS

Tel: 86-795-7205192

Fax:86-795-7205176

4SAFETY GUIDELINES

INFMANU4934/Rev C/March 2018

WARNING! An authorized Dealer or qualiﬁed technician must perform the initial setup of this

scooter and must perform all of the procedures in this manual.

The symbols below are used throughout this owner’s manual and on the scooter to identify warnings and import-

ant information. It is very important for you to read them and understand them completely.

WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated

procedures can cause either personal injury, component damage, or malfunction. On the

product, this icon is represented as a black symbol on a yellow triangle with a black border.

MANDATORY! These actions should be performed as speciﬁed. Failure to perform mandatory

actions can cause personal injury and/or equipment damage. On the product, this icon is

represented as a white symbol on a blue dot with a white border.

PROHIBITED! These actions are prohibited. These actions should not be performed at any

time or in any circumstances. Performing a prohibited action can cause personal injury and/or

equipment damage. On the product, this icon is represented as a black symbol with a red circle

and red slash.

INTENDED USE

The intended use of the mobility device is to provide mobility to persons limited to a seated position that

have the capability of operating a scooter.

This product is not a medical device and is not intended to assist, treat, diagnose or alleviate any medical condition

or disability.

NOTE: THIS OWNER’SMANUAL IS COMPILED FROM THE LATEST SPECIFICATIONS AND PRODUCT INFORMATION AVAILABLE

AT THE TIME OF PUBLICATION. WERESERVE THE RIGHT TO MAKE CHANGES AS THEY BECOME NECESSARY. ANY CHANGES TO

OUR PRODUCTS MAY CAUSE SLIGHT VARIATIONS BETWEEN THE ILLUSTRATIONS AND EXPLANATIONS IN THIS MANUAL AND THE

PRODUCT YOU HAVE PURCHASED. THE LATEST/CURRENT VERSION OF THIS MANUAL IS AVAILABLE ON OUR WEBSITE.

NOTE: THIS PRODUCT IS COMPLIANT WITH WEEE, ROHS, AND REACH DIRECTIVES AND REQUIREMENTS.

NOTE: THIS PRODUCT MEETS IPX4 CLASSIFICATION (IEC 60529).

NOTE: THE MID-SIZE SCOOTER AND ITS COMPONENTS ARE NOT MADE WITH NATURAL RUBBER LATEX. CONSULT WITH THE

MANUFACTURER REGARDING ANY AFTER-MARKET ACCESSORIES.

GT 3

CONTENTS

SAFETY GUIDELINES ............................................................................................... 2

I. SAFETY ............................................................................................................ 4

II. YOUR SCOOTER .............................................................................................. 6

III. BATTERIES AND CHARGING ......................................................................... 11

IV. OPERATION ................................................................................................... 17

V. COMFORT ADJUSTMENTS ............................................................................ 19

VI. DISASSEMBLY AND ASSEMBLY .................................................................... 21

VII. BASIC TROUBLESHOOTING .......................................................................... 22

VIII. CARE AND MAINTENANCE ........................................................................... 24

IX. SPECIFICATIONS ............................................................................................28

4GT

Manufactured in

Fully charge batteries before operating.

Remove key from an unattended Scooter.

Battery Set Conﬁguration:

+ = Positive (Red) Terminal Post

- = Negative (Black) Terminal Post

Connect Red wires to Red Positive (+) Terminal Posts.

Connect Black wire to Black Negative (-) Terminal Posts.

Read and follow the information in the owner’s manual.

I. SAFETY

PRODUCT SAFETY SYMBOLS

The symbols below are used on the scooter to identify warnings, mandatory actions, and prohibited actions. It is

very important for you to read and understand them completely.

NOTE: There are more warnings identiﬁed and explained in the Consumer Safety Guide that is included with

your scooter. Please become familiar with all the warnings and safety information found in the Consumer

Safety Guide and refer to this resource often.

Indicates UNOCCUPIED scooter securement points

Does not meet ISO 7176-19 standards for occupied transport in a motor

vehicle. When travelling in a motor vehicle, do not sit in your scooter.

GT 5

I. SAFETY

GENERAL

MANDATORY! Do not operate your new scooter for the ﬁrst time without completely reading and

understanding this owner’s manual and the Consumer Safety Guide.

Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. We provide an extensive

variety of products to best ﬁt the individual needs of the scooter user. Please be aware that the ﬁnal selection and

purchasing decision regarding the type of scooter to be used is the responsibility of the scooter user, who is capable

of making such a decision.

There are certain situations where the scooter user will need to practice operating the scooter in the presence of a

trained attendant.Atrained attendant can be deﬁned as a family member or someone capable of assisting a scooter

user in various daily living activities.

As you begin using your scooter during daily activities, you will probably encounter situations in which you will

need some practice. Simply take your time and you will soon be in full and conﬁdent control as you maneuver

through doorways, on and off elevators, up and down ramps, and over moderate terrain.

Additional general information can be found on the supplemental information sheets and booklets included in your

Owner’s Package. Please fully read and review the information, and keep it readily available for future reference.

Below are some precautions, tips and other safety considerations that will help you become accustomed to operating

the scooter safely.

PRE-RIDE SAFETY CHECK

Get to know the feel of your scooter and its capabilities. We recommend that you perform a safety check before

each use to make sure your scooter operates smoothly and safely.

Perform the following inspections prior to using your scooter:

Check the condition of the tires. Make sure they are not damaged or excessively worn.

Check all electrical connections. Make sure they are tight and not corroded.

Check all harness connections. Make sure they are secured properly.

Check the brakes to ensure they operate properly.

Check the battery condition meter to ensure the batteries are fully charged.

Ensure the manual freewheel lever is in drive mode before sitting on the scooter.

If you discover a problem, contact your authorized dealer for assistance. Please refer to the Contact Information

insert in your Owner’s Package.

BRAKING INFORMATION

Your scooter is equipped with these powerful brake systems:

Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the center/

stop position.

Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop or when

power is removed from the system for any reason.

6GT

II. YOUR SCOOTER

TILLER CONSOLE

The tiller console houses all of the controls needed to drive your scooter, including the speed adjustment dial, key

switch, battery condition meter, horn buttons, and the throttle control lever. Please note that some of the features

listed in this section are optional items and may not appear on your scooter. Contact your authorized dealer for

more information. See ﬁgure 1.

PROHIBITED! Do not expose the tiller console to moisture. In the event that the tiller console

does become exposed to moisture, do not attempt to operate your scooter until the tiller console

has dried thoroughly.

IDENTIFICATION KEY

Figure 1. Tiller Console

1. HORN BUTTON

2. LIGHT SWITCH

3. THROTTLE CONTROL LEVER

4. SPEED ADJUSTMENT DIAL

5. BATTERY CONDITION METER

6. KEY SWITCH

GT 7

II. YOUR SCOOTER

Horn Buttons

These buttons activate a warning horn. Your scooter must be powered up for the horn to be operational.

Do not hesitate to use the warning horn when doing so may prevent accident or injury.

Lights Switch

This switch controls your scooter’s lighting system.

Press button to turn on light.

Press button again to turn light off.

WARNING! Scooter users are required to use their lights when visibility is restricted—day or

night.

Throttle Control Lever

This lever allows you to control the forward speed and the reverse speed of your scooter up to the maximum speed

you preset with the speed adjustment dial.

To use throttle control lever:

To move Forward, use either of the following:

Use your left thumb to push the left side of the throttle control lever.

Use your right hand ﬁngers to pull back on the right side of the throttle control lever.

To move Rearward, use either of the following:

Use your right thumb to push the right side of the throttle control lever.

Use your left hand ﬁngers to pull back on the left side of the throttle control lever.

Release the throttle control lever and allow your scooter to come to a complete stop before engaging the other side

of the lever. When the throttle control lever is completely released, it automatically returns to the center “stop”

position and engages your scooter’s brakes.

Speed Adjustment Dial

This dial allows you to preselect and limit your scooter’s top speed.

The image of the tortoise represents the slowest speed setting.

The image of the hare represents the fastest speed setting.

Battery Condition Meter

When the key is fully inserted and turned clockwise to power up your scooter, this meter indicates the approximate

battery voltage strength. For further information on battery charging, see III. “Batteries and Charging.”

Key Switch

Insert the key into the key switch and turn it clockwise to power up (turn on) your scooter.

Turn the key counterclockwise to power down (turn off) your scooter.

WARNING! If the key is turned to the “off” position while your scooter is in motion, the electronic

brakes will engage and your scooter will come to an abrupt stop!

8GT

Off-board Charger Port

The off-board charger power cord plugs into this port during battery charging. The off-board charger port is

located on the tiller.

REAR COMPONENTS

The manual freewheel lever, anti-tip wheels, motor/transaxle assembly, and optional safety ﬂag brackets are

located on your scooter as shown. See ﬁgure 2.Although not shown, the batteries and main circuit breaker (reset

button) are also located on the rear component section of your scooter.

WARNING! Before placing your scooter into or taking it out of freewheel mode, remove the key

from the key switch. Never sit on a scooter when it is in freewheel mode. Never put a scooter in

freewheel mode on any incline.

II. YOUR SCOOTER

Manual Freewheel Lever

Whenever you need or want to push your scooter

for short distances, you can put it in freewheel

mode.

1. Remove the key from the key switch.

2. Push forward on the manual freewheel lever to

disable the drive system and the brake system.

This will enable you to push the scooter.

NOTE: If your scooter is equipped with a

2-position manual freewheel lever, you must pull

up on the lever and then push forward on the

manual freewheel lever to disable the drive system

and the brake system. This will enable you to push

the scooter.

3. Pull back on the manual freewheel lever to

reengage the drive and the brake systems and

take your scooter out of freewheel mode.

IDENTIFICATION KEY

1. MANUAL FREEWHEEL LEVER

2. MOTOR/TRANSAXLE ASSEMBLY

3. ANTI-TIP WHEELS

Figure 2. Rear Components

GT 9

WARNING! When your scooter is in freewheel mode, the braking system is disengaged.

Disengage the drive motors only on a level surface.

Ensure the key is removed from the key switch.

Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on a

scooter to do this.

After you have ﬁnished pushing your scooter, always return it to the drive mode to lock the

brakes.

NOTE: If the scooter is placed in freewheel mode (manual freewheel lever forward) while the key is in the

“on” position, the scooter will not run until the manual freewheel lever is pushed rearward and the key is

turned to the “off” position, then back to the “on” position.

Motor/Transaxle Assembly

The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your scooter’s

batteries into the controlled mechanical energy that drives the scooter’s wheels.

Anti-Tip Wheels

The anti-tip wheels are an integral and important safety feature of your scooter. They are bolted to the frame at

the rear of the scooter.

PROHIBITED! Do not remove the anti-tip wheels or modify your scooter in any way that is not

authorized by your dealer.

WARNING! The anti-tip wheels may cause interference with the smooth transition of your scooter

when ascending or descending a curb. Contact your authorized dealer for more information.

II. YOUR SCOOTER

Main Circuit Breaker (Reset Button)

When the voltage in the batteries becomes low or your

scooter is heavily strained because of excessive loads,

the main circuit breaker may trip to protect the motor

and electronics from damage. When the breaker trips, the

entire electrical system shuts down. See ﬁgure 3.

The reset button pops out when the breaker trips.

Allow a minute or so for the electronics to “rest.”

Push in the reset button to reset the breaker.

Ifthebreakertripsfrequently,youmay need tocharge

the batteries more often or have your authorized

dealer perform a load test on the batteries.

If the main circuit breaker trips repeatedly, see your

authorized dealer for service.

Figure 3. Main Circuit Breaker (Reset Button)

Batteries

The batteries store electrical energy that powers your scooter. See III. “Batteries and Charging ” for information

on how to charge your scooter batteries.

10 GT

SECURING THE SCOOTER

Always secure the scooter in a forward-facing position in the vehicle. Attach the four tie-down straps to the

designated securement points. See ﬁgure 4. Tighten the straps to sufﬁciently remove all slack. Never attach

tie-downs to adjustable, moving or removable parts of the scooter such as armrests, shrouds, and wheels. Any

removable items should be removed and stowed separately. Position the anchor points for the rear tie-down straps

directly behind the rear securement points on the scooter. The front tie-down straps should anchor to ﬂoor points

that are spaced wider than the scooter to provide increased lateral stability.

WARNING! Ensure scooters are properly secured to the motor vehicle during transport. Scooters

that are not properly secured can become a hazard to the user and to other vehicle passengers

in the event of a crash, sudden stopping, or swerving, as the scooter could tip or slide out of

place. Do not secure a scooter by any of its removable parts such as armrests, seat, basket,

accessory brackets, etc.

Figure 4. Securement Points (Identiﬁed with black dots)

II. YOUR SCOOTER

IDENTIFICATION KEY

1. FRONT SECUREMENT POINTS (3-WHEEL MODELS)

2. FRONT SECUREMENT POINTS (4-WHEEL MODELS)

3. REAR SECUREMENT POINTS

Tabla de contenidos

Otros manuales de Silla de ruedas de Pride Mobility

Pride Mobility

Pride Mobility Quantum Jazzy series Manual de usuario

Pride Mobility

Pride Mobility ACCASMB2287 Manual del propietario

Pride Mobility

Pride Mobility JAZZY Jazzy 1113 Manual de usuario

Pride Mobility

Pride Mobility QUANTUM SERIES Manual de usuario

Pride Mobility

Pride Mobility JAZZY 1103 ULTRA Manual de usuario

Pride Mobility

Pride Mobility JAZZY 1121 Manual del propietario

Pride Mobility

Pride Mobility Jazzy 1170 XL Manual de usuario

Pride Mobility

Pride Mobility Jazzy1133 Manual de usuario

Pride Mobility

Pride Mobility REAR-WHEEL DRIVE POWER CHAIRS Quantum R-4000 Manual de usuario

Pride Mobility

Pride Mobility Jet 7 Manual de usuario

Pride Mobility

Pride Mobility CELEBRITY XL-8 Manual de usuario

Pride Mobility

Pride Mobility 1170XL Plus 2VHD, 1170XL Plus Manual de usuario

Pride Mobility

Pride Mobility Quantum 6000Z series Manual de usuario

Pride Mobility

Pride Mobility Jazzy 1133 Manual de usuario

Pride Mobility

Pride Mobility JET1 Manual de usuario

Pride Mobility

Pride Mobility SPARKY Manual de usuario

Pride Mobility

Pride Mobility Quantum 1650 Manual de usuario

Pride Mobility

Pride Mobility Jet 3 Ultra Manual de usuario

Pride Mobility

Pride Mobility JAZZY Sport 2 Manual de usuario

Pride Mobility

Pride Mobility Go-Chair Manual de usuario

Pride Mobility

Pride Mobility Quantum Jazzy series Manual de usuario

Pride Mobility

Pride Mobility Quantum Q6 Edge 2 Manual de usuario

Pride Mobility

Pride Mobility Quantum Q6 Edge HD Manual de usuario

Pride Mobility

Pride Mobility QUANTUM SERIES Manual de usuario

Manuales populares de Silla de ruedas de otras marcas

Otto Bock

Otto Bock Skippi plus Manual de usuario

Invacare

Invacare Action 4NG series Manual de usuario

SORG

SORG LoopSORG 802 Manual de usuario

Designability

Designability WizzyBug Instrucciones de instalación

Vermeiren

Vermeiren RAPIDO Manual de usuario

Excel

Excel G5 KIDS 0285 Manual de usuario

M. Bartels

M. Bartels SA-3 Manual de usuario

nino robotics

nino robotics NIno Manual de usuario

Vermeiren

Vermeiren Turios Manual de usuario

Invacare

Invacare MK5 EX Manual de usuario

Invacare

Invacare Solara Spree GT Manual

Nova

Nova TKW-12 Manual de usuario

BCW

BCW Advantage Manual de usuario

You-Q

You-Q Luca Manual de usuario

interco

interco Ortolight Standard Manual de instrucciones

Nova

Nova 7190L Manual de usuario

Vermeiren

Vermeiren EZ1 Manual de usuario

PaceSaver

PaceSaver Scout M-300 Manual de usuario