Premium PAD12060ENW/S Manual de usuario
Identification of parts
Safety Precautions
Preparation before use
Installation instructions
2
1
Indoor unit 3
Outdoor unit 3
Display introduction 4
Remote controller 8
Select the installation locations 19
Indoor unit installation 20
Outdoor unit installation 25
Installation diagram 18
Air purging 25
Notes 26
Operation instructions
Operation modes 10
Airflow direction control 11
Smart mode 12
Timer mode 13
Sleep mode 14
Maintenance 15
Protection 16
Troubleshooting 17
Super mode 14
Contents
1
Preparation before use
Before using the air conditioner, be sure to check and preset as the following.
Remote Controller presetting
Auto Restart Presetting
It will be turned off automatically after about 10 seconds.
Hold down any button of the remote controller for about 2 seconds, the back-light will be turned on.
Note: Back-light is an optional function.
Back-light function (optional)
Each time after the remote control is replaced with new batteries or is energized, remote control auto
presetting heat pump.If the air conditioner you purchased is a Cooling Only one, heat pump remote
controller can also be used .
The air conditioner has Auto-Restart function.
You can set or cancel this function when the air conditioner is running.
Hold down the emergency button(ON/OFF) for a few seconds, this function will be set if you hear
beep twice. If you just hear beep once, this function will be canceled.
Safety precautions
Symbols in this Use and Care Manual are interpreted as shown below.
Be sure not to do.
Pay attention to such a situation.
Grounding is essential.
Do not use the power supply circuit
breaker or pull off the plug to turn it off
during operation. This may cause a fire
due to spark, etc.
Keep the power supply circuit breaker
or plug from dirt. Connect the power
supply cord to it firmly and correctly,
lest an electric shock or a fire break out
due to insufficient contact.
Use correct power supply in
accordance with the rating plate
requirement. Otherwise, serious
faults or hazard may occur or a
fire maybe break out.
Do not knit, pull or press the power supply
cord, lest the power supply cord be broken.
An electric shock or fire is probably caused
by a broken power supply cord.
Never insert a stick or similar obstacle
to the unit. Since the fan rotates at high
speed, this may cause an injury.
Do not repair the appliance by yourself.
If this is done incorrectly, it may cause an
electric shock, etc.
Turn off the appliance by remote control
firstly before cutting off power supply if
malfunction occurs.
It is harmful to your health if the cool air
reaches you for a long time. It is advisable
to let the air flow be deflected to all the room.
Prevent the air flow from reaching the gas
burners and stove.
Do not touch the operation buttons
when your hands are wet.
Do not put any objects on the outdoor
unit.
It is the user's responsibility to make the
appliance be grounded according to
local codes or ordinances by a licenced
technician.
OFF OFF
ON
ON
Warning: Incorrect handling could
cause a serious hazard, such as death,
serious injury, etc.
2
ON/OF F
MODE FAN
SWING S LEEP SUPER
SMART I FEEL DIM MER
TIMER O N TIMER O FF CLOCK
ON
OFF
ON
OFF
The figures in this manual are based on the external view of a standard model.
Consequently, the shape may differ from that of the air conditioner you have selected.
Air Intake
Air Intake
Air Outlet
Air Outlet
Louver
Vertical Adjustment
Louver
Horizontal Adjustment
Air Filter
Remote Controller
Connection Cord
Pipes and Power
Drain Hose
Front Panel
Emergency Panel
Display Panel
Note: Condensate water drains
at COOLING or DRY operation.
Identification of parts
3
Indoor unit
Outdoor unit
ON/OF F
MODE FAN
SWING SLE EP SUPER
SMART IFEE LDIM ME R
TIMER ON TIMER OFF CLO CK
ON
OFF
ON
OFF
The symbols may be different from these models, but the functions are similar.
Display introduction
4
1 2 3 4 5 6
Running indicator
It lights up when the AC is running.
It flashes during defrosting.
2
Timer indicator
It lights up during set time.
3
Sleep indicator
It lights up in sleep mode.
4
Compressor indicator
It lights up when the compressor is on.
5
Display set temperature.
It shows FC after 200 hours of usage as reminder to clean the filter.
After filter cleaning press the filter reset button located on the indoor unit behind the front
panel in order to reset the display.(optional)
Temperature indicator
VG/VL series
1
Signal Receptor 6
Timer
Comp.
Run
Sleep
VQ series
12
34
6
12
34
5
The symbols may be different from these models, but the functions are similar.
Display introduction
5
1
2
34
5
6
12
34
5
6
NS series
VT series
NT series
6
4
4
3
2
The symbols may be different from these models, but the functions are similar.
Display introduction
6
12
34
5
6
Timer Comp. Run Sleep
UL series
UQ series
UP series
6
Timer Comp. Run Sleep
12
34
5
12
34
5
6
ON/OFF
Filter reset
7
To let the AC run or stop by pressing the button.
When the display shows "FC", it will function as
a reset button of the filter cleaning prompt.
Emergency button 7
The symbols may be different from these models, but the functions are similar.
7
Display introduction
ON/OFF
To let the AC run or stop by pressing the button.
VC series
12
34
5
6
Timer Comp. Run Sleep
12
34
5
6
The remote controller transmits signals to the system.
Remote controller
8
1
2
4
3
13
12
5
6
11
7
8
9
10
SUPER BUTTON
SWING BUTTON
FAN BUTTON
ROOM TEMPERATURE
SETTING BUTTONS
SLEEP BUTTON
IFEEL BUTTON (optional)
CLOCK BUTTON
ON/OFF BUTTON
SMART BUTTON
MODE BUTTON
TIMER ON/OFF BUTTON
Used to start or stop the fast cooling/heating.
(Fast cooling operates at high fan speed with
18℃ set temp automatically ; Fast heating
operates at auto fan speed with 32℃ set temp
automatically)
Used to stop or start vertical adjustment
louver swinging and set the desired up/down
airflow direction.
Used to select fan speed in sequence
auto, high, medium or low.
Used to set or cancel Sleep Mode operation.
Used to set or cancel Mode operation.IFEEL
Used to set the current time.
Used to enter fuzzy logic operation directly,
regardless of the unit is on or off.
The appliance will be started when it is
energized or will be stopped when it is
in operation, if you press this button.
Press this button to select the operation mode.
Used to set or cancel the timer operation.
Remote controller
Indication symbols on LCD:
Note: Each mode and relevant function will be further specified in following pages.
Signal transmit
Dry indicator
Fan only indicator
Heating indicator
Cooling indicator
High fan speed
Medium fan speed
Low fan speed Display set temperature
Display set timer
Display current time
Auto fan speed Smart indicator
Sleep indicator
Ifeel
Super indicator
ON
OFF
10
11
12
13
14
14
3
4
ON/OFF
MODE FAN
SWING SLEEP SUPER
SMART IFEEL DIMMER
TIMER ON TIMER OFF CLOCK
ON
OFF
ON
OFF
1
2
6
7
5
8
9
Used to adjust the room temperature and
the timer, also real time.
DIMMER BUTTON (optional)
When you press this button, all the display of
indoor unit will be closed. Press any button to
resume display.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Acondicionador de aire de Premium
Premium
Premium PPA1207 Manual de usuario
Premium
Premium PWA0510G Manual de usuario
Premium
Premium PAC9028 Manual de usuario
Premium
Premium PAC1203711 Manual de usuario
Premium
Premium PIA9066A Manual de usuario
Premium
Premium PIA122690A Manual de usuario
Premium
Premium PWA0810N Manual de usuario
Premium
Premium PWA0510N Manual de usuario
Premium
Premium PIA12061 Manual de usuario
Premium
Premium PAC36007 Manual de usuario
Premium
Premium PWA1210N Manual de usuario
Premium
Premium PIAW Series Manual de usuario
Premium
Premium PAC24039G Manual de usuario
Premium
Premium PIAW9169A Manual de usuario
Premium
Premium PAC366FC-I Manual de usuario
Premium
Premium PWA1210G Manual de usuario
Premium
Premium PAC3003711A Manual de usuario
Premium
Premium PAC9039 Manual de usuario
Premium
Premium PIAW9164A Manual de usuario
Premium
Premium PIA9064A Manual de usuario
