Premier Technology CH 6000 Manual de usuario
CALL HANDLER 6000 INSTALLATION INSTRUCTIONS 1
1
Preparation
•Make sure that all the phone lines to be connected to the Call
Handler are standard pots (plain old telephone) lines (NOT T1,
ISDN or DSL lines).
•Determine location of phone lines and phone numbers to be
connected to the Call Handler.
• Determine which line will be used for downloads (the least
used line) and connect it to the Call Handler.
• Determine if phone system has a music-on-hold port, the
location and type of connection.
• Determine if customer has Caller ID. If Caller ID is built into
the phone system, then the Caller ID will not work because it
is blocked by the Call Handler. If a separate Caller ID device(s)
are used, then the Caller ID connection(s) to the phone line(s)
must be made between the phone line demarcation block
(entrance) and the RJ31X block(s) (you may need to re-wire
the Caller ID wiring to keep it connected in front of the Call
Handler).
•Determine access to 120VAC for Call Handler power (Make
sure that the power is not switched off after business hours).
•Decide mounting location for the Call Handler. Typically, this
will be in the phone closet.
• Decide where you will cut each phone line and where you will
insert the RJ31X block in series with that phone line (The
RJ31X should be located within 3 feet of the Call Handler due
to cable lengths provided with the Call Handler).
continued next page...
2CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
2
Table of Contents
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . .5-7
Call Handler Modes of Operation . . . . . . . . . . . . . . .8-9
Caller ID Information . . . . . . . . . . . . . . . . . . . . . . . . . .10
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Voice Mail Compatibility . . . . . . . . . . . . . . . . . . . . . . .11
Installation Diagrams . . . . . . . . . . . . . . . . . . . . . . . . .12
Warranty and FCC Information . . . . . . . . . . . . . . . . . .13
3CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
...continued from previous page
•Determine if the Call Handler is in “factory default”
configuration or if the unit has been pre-downloaded with audio
messages and other configuration settings (This will determine
the operating mode of the Call Handler).
Connections
1) Phone Lines – for PBX and key switch phone systems, the
main published number should be connected to phone line
number one in the roll over group, the second line of the roll
over group to phone line number two, and the phone line
number three takes the last roll over number.
2) Serial Port – not used at this time.
3) Reset Button – this button re-initializes the microprocessor
and brings the screen back to idle. None of the settings will be
erased.
4) 600 ohm and 8 ohm outputs – one of these outputs is to be
connected to the music on hold port of the phone system. This
will allow for the playing of a message on hold while the
customer has been put on hold.
5) Tape Input and Handset – these two jacks allow for local
downloading either from a tape player or a handset jack. The
handset jack must be an old style carbon microphone for
proper operation (available through Premier Technologies).
6) AC Adapter - 10 VAC power output
7) Earth Ground Connector - To reduce unwanted interference.
NOTE: Connection is mandatory for use with ground start phone
systems.
4CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
1
2
3
4
5
6
7
5CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
Installation Instructions
1) Mount the Call Handler on the Wall
2) Break each phone line between the demarcation block and
the inside phone system. Install one of the provided RJ31X
blocks in series (not in parallel) with each phone line. Do not
plug the RJ45 (8 wire) patch cord into the RJ31X blocks at
this time.
When using the RJ31X blocks provided with the Call Handler,
make the following connections:
• Connect the outside phone line to terminals 4 & 5 of the
RJ31X.
• Connect the inside phone line to terminals 1 & 8 of the
RJ31X.
3) Plug the AC adapter into a 120VAC outlet. Power-up the Call
Handler by plugging the AC adapter mini-plug into the 10VAC
power connector on the Call Handler. Verify that the LCD
display is operating. The display will indicate the current
operating mode for each of the 3 lines.
If the Call Handler is pre-downloaded, skip to step # 6.
4) Connect one RJ45 phone line patch cord from one of the
phone line connectors on the Call Handler to the RJ31X block
on the phone line that will be used for downloading. The Call
handler will intercept calls on that phone line only. Don’t
connect the other phone lines to the Call Handler yet,
because we want to first get the Handler downloaded and
configured properly.
6CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
Note: If you hear constant clicking from the Call Handler or if the LCD display
indicated “RING” with no incoming call, then you have the incoming and
outgoing lines on the RJ31X block reversed. Swap the wires on terminals
1 & 8 with those on 4 & 5.
Note: If the Call Handler is in off, screen, or night answer mode, then the
inside phones will ring. The call may be answered by someone which will
interfere with the download. You may need to ask people not to answer calls
on the download line (during the download operation) or you may decide to
temporarily disconnect the inside phone line (terminals 1 & 8) from the RJ31X
block on the download line only. This will prevent interference from inside
people as well as preventing incoming calls being answered by the business.
If the Call Handler is in promo mode, then the download computer will be able
to get into the Call Handler before the inside phone lines ring.
5) Call the Download Center and ask them to download to the
Call Handler. Wait until the download operator confirms that
the download has been completed successfully. Ask the
download operator the following questions:
• “What mode should the Call Handler be set?”
• “The unit is programmed to answer after how many rings?”
• Verify that the Call Handler display indicates the correct
operating mode.
• Re-connect the inside phone line on the download RJ31X
block (if it was disconnected).
• Call into the download line to verify correct operation of the
Call Handler
6) Connect the remaining RJ45 patch cords from the phone
line connections on the Call Handler to the RJ31X blocks.
Note: If you hear constant clicking from the Call Handler or if the LCD
display indicated “RING” with no incoming call, then you have the
incoming and outgoing lines on the RJ31X block reversed. Swap the
wires on terminals 1 & 8 with those on 4 & 5.
continued next page...
7CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
...continued from previous page
7) Call into each line of the Call Handler to verify correct
operation, per the mode of operation. Verify sound quality
of audio messages.
8) Connect an RCA audio cable from the 600 ohm port on the
Call Handler to the music-on-hold port of the phone system.
Call into the business and ask to be placed on hold. Adjust
the audio volume at the Handler keypad. If sufficient volume
cannot be achieved at the 600 ohm port then switch to the 8
ohm port.
CAUTION: Turn down the volume before making the connection
so you do not “blast” the phone system (refer to the volume
adjustment section on page 10 for further details).
CAUTION: If the music-on-hold port uses a punch-down block,
do not directly connect the stranded wire from an RCA cable to
the punch-down block. Punch-down blocks are designed to only
work with standard telephone solid core wire, not stranded wire.
Connect a short length of solid telephone wire to the punch-
down block. Cut off one end of the provided RCA audio cable
and splice the two stranded wires to the solid telephone wires
(Insufficient or intermittent volume can result if stranded wire is
used at the punch-down blocks).
9) Call the Download Center and notify them that the Call
Handler has been installed successfully or ask them for
assistance if there are problems. Make sure that the Call
Handler is working properly before you leave the site.
8CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
Call Handler Modes of Operation
Note: A new unit will not have messages but will behave the same as
described below.
Promo Mode: The call Handler answers an incoming call on
the programmed number of rings (default is
2). The Call Handler plays a short
promotional message, then the Handler
switches to a transfer message (this may be
the same as the on-hold message) and
begins to ring the inside phone system. When
someone answers the incoming call, the Call
Handler connects the caller to the inside
phone system.
Screen Mode: The Call Handler immediately begins to ring
the inside phone during an incoming call.
When someone answers the incoming call
the Call Handler connects the caller to the
inside phone system. If the programmed
number of rings (default is 4) is reached
before the inside phone system answers the
call, then the Call Handler answers the
incoming call, plays a short screen message
and then switches to the transfer message.
The call handler continues to ring the inside
phone system while the messages are being
played. When someone answers the incoming
call, the caller is then connected through to
the phone system.
continued next page...
9CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
Night The Call Handler answers an incoming call on
Answer the programmed number of rings (default is 1)
Mode and plays a night answer message. At the
end of the message, the Call Handler
disconnects. Optionally, the Call Handler can
ring the inside phone system while the night
answer message is playing.
Off Mode The Call Handler passes calls through to the
inside phone system with no interaction. The
Call Handler will answer an incoming call after
16 rings so that a unit in the “off” mode can still
receive a download.
Power If power is removed or unplugged from the Call
Problems Handler unit, the call handler will pass calls
through unaffected, until power is restored to
the unit.
Music - The music on-hold port continuously plays the
on - music on-hold message (may be the same as
hold the transfer message) into the music on-hold
port of the phone system. The volume control
works with this port only. The other operating
modes do not affect the music-on-hold.
...continued from previous page
10 CALL HANDLER 6000 INSTALLATION INSTRUCTIONS
Caller ID Information
Caller ID information is sent by the phone company approximately
1/2 second after the first ring. Therefore, for Caller ID to work, the
answering devices must not pick up before the 2nd ring. If Caller ID
is built into the customer’s phone system, then the Caller ID will not
work because the Call Handler is blocking the Caller ID information
at this point in time If the customer has a Caller ID box that is
separate from the phone system, then that Caller ID phone inter-
face must be connected in front of the Call Handler.
Volume Adjustment on 8 ohm or 600 ohm
music-on-hold output port of Call Handler
Call into one of the phone lines and ask to be placed “on hold.”
Listen to the on-hold message and adjust the volume on the Call
Handler. Use the keypad and display on the Call Handler to change
the volume as indicated below:
Press “Setup” Display shows: “Setup (Accept/Cancel)”
Press “Accept” Display shows: “1 Security (Accept/Cancel)”
Press “Next” Display shows: “2 Volume (Accept/Cancel)”
Press “Accept” Display shows: “Volume is at XX Acc/Can
Inc/Dec”
Now press “Increase” or “Decrease” to change the output volume.
When you are done adjusting the volume;
Press “Accept” Display shows: “2 Volume (Accept/Cancel)”
Press “Cancel” Display shows: current Call Handler modes.
Tabla de contenidos
Manuales populares de Caja de identificación de llamadas de otras marcas
ClassCo
ClassCo VoiceAnnounce 9900CW Manual de usuario
Radio Shack
Radio Shack System 420 Manual de usuario
GE
GE 2-9030 Manual de usuario
GE
GE 290961 - Call Waiting Caller ID Manual de usuario
Geemarc
Geemarc Clearview Cordless Caller Display Unit Manual de usuario
Radio Shack
Radio Shack 43-931 Manual de usuario
ClassCo
ClassCo VoiceAnnounce 9900CW Manual de usuario
Panacom
Panacom PA-7018 Manual de usuario
Radio Shack
Radio Shack System 200 Manual de usuario
Radio Shack
Radio Shack SYSTEM 2100 Manual de usuario
CallerID
CallerID Whozz Calling? 4 POS Caller ID Manual de usuario
Radio Shack
Radio Shack CID-947 Manual de usuario