Predator ORION 3000 Manual de usuario
PREDATOR ORION 3000
USER’S MANUAL
2 -
© 2020. All Rights Reserved.
Predator Desktop Computer
Covers: PO3-620
This revision: April 2020 V1.00
Register your Predator product
Model number: _________________________________
Serial number: __________________________________
Date of purchase: ______________________________
Place of purchase: _____________________________
Important
This manual contains proprietary information that is protected
by copyright laws. The information contained in this manual is
subject to change without notice. Some features described in this
manual may not be supported depending on the Operating
System version. Images provided herein are for reference only
and may contain information or features that do not apply to
your computer. Acer Group shall not be liable for technical or
editorial errors or omissions contained in this manual.
If your new device runs on Windows OS, you may have had
your product registered automatically while you start up
your device with Windows OS.
Log in at www.acer.com/myproducts with the email address
you registered for Windows OS to review your product
record. (Reset your password if you do not know it.)
If the record is not found, please follow the steps below to
register.
1. Ensure you are connected to the Internet.
2. Go to www.acer.com/register-product.
3. Sign in or sign up for an Acer ID.
4. Enter S/N or SNID of your device to register it.
Table of contents - 3
TABLE OF CONTENTS
1 Upgrading your computer 4
Installation precautions......................... 4
ESD precautions............................................. 4
Required tools ................................................. 4
Pre-installation instructions ................... 5
Post-installation instructions................. 5
System cover................................................ 6
Removing the left side system cover 6
Installing the left side system cover . 7
Removing the left side transparent
cover ..................................................................... 8
Installing the left side transparent
cover ..................................................................... 9
Hard drives .................................................. 10
Removing the 3.5-inch hard drives.. 10
Installing the 3.5-inch hard drives .. 12
Memory ......................................................... 14
Memory configuration guidelines ..... 14
Removing a memory module................ 15
Installing a memory module ................ 16
Graphics board........................................... 17
Removing the graphics board .............. 17
Installing the graphics board............ 20
SSD module ................................................ 22
Removing the SSD module ................... 22
Installing the SSD module ................... 24
2 PredatorSense 26
PredatorSense features..................... 26
Lighting ............................................................. 27
Fan Control.................................................... 28
Monitoring...................................................... 29
4 - 1 Upgrading your computer
1 UPGRADING YOUR COMPUTER
Installation precautions
Before you install any computer component, we recommend
that you read the following sections. These sections contain
important ESD precautions along with pre-installation and
post-installation instructions.
ESD precautions
Electrostatic discharge (ESD) can damage your processor,
disk drives, expansion boards, and other components.
Always observe the following precautions before you install
a computer component:
1. Do not remove a component from its protective packaging
until you are ready to install it.
2. Wear a wrist grounding strap and attach it to a metal part
of the computer before handling components. If a wrist
strap is not available, maintain contact with the computer
throughout any procedure requiring ESD protection.
Required tools
In performing the component replacement process, you will
need the following tools:
• Philips screwdriver
•Hexscrewdriver
• Flat screwdriver
•Scissors
Note
The screws for the different components vary in size. During the
disassembly process, group the screws with their corresponding
components to avoid mismatches when putting back the
components.
1 Upgrading your computer - 5
Pre-installation instructions
Always observe the following before you install any
component:
1. Make sure that the ODD and card reader slot is empty.
2. Turn off the power to the computer and all peripherals.
3. Unplug the power cord from the computer.
4. Unplug the network cable and all connected peripheral
devices from the computer.
5. Place the computer on a flat, steady surface.
6. Open your computer according to the instructions on
Removing the left side system cover on page 6.
7. See the following sections for specific instructions on the
component you wish to install.
Post-installation instructions
Observe the following after installing a computer
component:
1. See to it that the components are installed according to
the step-by-step instructions in their respective sections.
2. Replace any expansion boards or peripherals that you
removed earlier.
3. Replace the system cover. See Installing the left side
system cover on page 7.
4. Connect the necessary cables.
5. Turn on your computer.
Warning
Not turning off the computer properly before you start installing
the components may cause serious damage. Do not attempt the
procedures described in the following sections unless you are a
qualified service technician.
6 - 1 Upgrading your computer
System cover
Removing the left side system cover
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre-installation instructions on page 5.
2. Remove the two screws that secure the system cover to
the computer (1).
3. Slide the cover toward the back of the computer and pull
away from the side of the computer (2).
4. Set the cover aside for re-installation later.
8 - 1 Upgrading your computer
Removing the left side transparent cover
(For systems with transparent cover only)
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre-installation instructions on page 5.
2. Remove the four screws that secure the transparent cover
to the computer (1).
3. Gently detach the cover from the side of the computer (2).
4. Set the cover aside for re-installation later.
Otros manuales para ORION 3000
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de De oficina de Predator
