PRECISION DIGITAL ProtEX Series Manual de usuario

ProtEX PD8-6080/PD8-6081 Explosion-Proof

Modbus®Scanner Instruction Manual

PRECISION DIGITAL CORPORATION

233 South Street • Hopkinton MA 01748 USA

Tel (800) 343-1001 • Fax (508) 655-8990 www.predig.com

Modbus Scanner

•Modbus®RTU Master, Slave, or Snooper Mode

•Poll and Display up to 16 Process Variables

•Two (2) 0-20 mA, 4-20 mA, 0-5 V, 1-5 V, and ±10 V Inputs

•Math functions Capabilities

•Isolated 24 VDC @ 25 mA Transmitter Power Supply

•Multi-Pump Alternation Control

•Signal Input Conditioning for Flow & Round Horizontal Tank

•Programmable Displays & Function Keys

•32-Point, Square Root, or Exponential Linearization

•Up to Three 4-20 mA Analog Outputs Available

•Modern, Sleek and Practical Enclosure

•Display Mountable at 0°, 90°, 180°, & 270° Degrees

•Explosion-Proof, IP68, NEMA 4X Enclosure

•SafeTouch®Through-Glass Button Programming

•Flanges for Wall or Pipe Mounting

•Superluminous Sunlight Readable Display

•Free USB Programming Software & Cable

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Disclaimer

The information contained in this document is subject to change without notice.

Precision Digital Corporation makes no representations or warranties with respect to the

contents hereof; and specifically disclaim any implied warranties of merchantability or

fitness for a particular purpose.

Caution

Read complete instructions prior to installation

and operation of the scanner.

Warning!

Risk of electric shock or personal injury. Hazardous voltages exist

within enclosure. Installation and service should be performed

only by trained service personnel.

Warning!

•This product is not recommended for life support applications or

applications where malfunctioning could result in personal injury or

property loss. Anyone using this product for such applications does

so at his/her own risk. Precision Digital Corporation shall not be held

liable for damages resulting from such improper use.

•Failure to follow installation guidelines could result in death or

serious injury. Make sure only qualified personnel perform the

installation.

•Never remove the instrument cover in explosive environments when

the circuit is live.

•Cover must be fully engaged to meet flameproof/explosion-proof

requirements.

•Information in this manual supersedes all enclosure, compliance,

and agency approval information included in additional product

manuals included with this product.

Limited Warranty

Precision Digital Corporation warrants this product against defects in material or

workmanship for the specified period under “Specifications” from the date of shipment

from the factory. Precision Digital’s liability under this limited warranty shall not exceed

the purchase value, repair, or replacement of the defective unit.

Registered Trademarks

Modbus®is a Registered Trademark of Schneider Automation Inc. All other trademarks

mentioned in this document are the property of their respective owners.

www.predig.com

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Table of Contents

Table of Contents-----------------------------------------3

Table of Figures -------------------------------------------4

Introduction-------------------------------------------------5

Ordering Information ------------------------------------6

Specifications----------------------------------------------7

Operating Modes ----------------------------------------------7

Master & Snooper Settings---------------------------------7

PV Settings ------------------------------------------------------7

Display Settings------------------------------------------------7

Math Functions-------------------------------------------------8

Serial Communications--------------------------------------8

General------------------------------------------------------------8

Relays -------------------------------------------------------------9

Isolated 4-20 mA Transmitter Output-------------------9

Digital Inputs & Outputs-------------------------------------9

Dual Process Input------------------------------------------10

MeterView Pro ------------------------------------------------10

Product Ratings and Approvals;-----------------------11

Compliance Information ------------------------------ 12

Safety------------------------------------------------------------12

Electromagnetic Compatibility--------------------------12

Safety Information-------------------------------------- 13

Installation ------------------------------------------------ 13

Unpacking------------------------------------------------------13

Pre-Installed Conduit/Stopping Plug------------------14

Mounting -------------------------------------------------------14

Cover Jam Screw--------------------------------------------14

Transmitter Supply Voltage Selection (P+, P-) ----14

Connections---------------------------------------------------15

Required & Factory Wired Connection---------------15

Connectors Labeling--------------------------------------16

Power Connections ---------------------------------------16

Serial Communications Connections-----------------17

Using PROVU Serial Adapters---------------------------19

F4 Digital Input Connections----------------------------19

Relay Connections ----------------------------------------19

Switching Inductive Loads-------------------------------20

4-20 mA Output Connections---------------------------20

Analog Output Transmitter Power Supply-----------20

Interlock Relay Feature ----------------------------------21

Analog Input Signal Connections----------------------21

Digital I/O Connections-----------------------------------23

External Switch Contacts--------------------------------23

Setup and Programming------------------------------ 24

Overview--------------------------------------------------------24

SafeTouch®Buttons----------------------------------------24

Front Panel Buttons and Status LED Indicators--25

ScanView Software -----------------------------------------26

ScanView Installation-------------------------------------26

Display Functions & Messages-------------------------27

Menu Navigation Tip----------------------------------------30

Setting Numeric Values -----------------------------------30

Main Menu -----------------------------------------------------30

Serial Communications (serial)-----------------------31

Scanner Mode Selection ----------------------------------32

Operating Modes (nmode) ---------------------------------32

How to Enable Process Variables (PVs)-------------32

Master Mode (nmastr)----------------------------------- 33

Snooper Mode (Snoopr) ----------------------------------- 34

How to Select 5 or 6-Digit Registers------------------ 35

Slave Mode (Slave) -------------------------------------- 35

Setting Up the Scanner (setup)------------------------- 36

Setting Up the Process Variables (PVs) (pv setup)

----------------------------------------------------------------- 37

Setting the Display Decimal Point (disp.dp)--------- 37

Setting the Float Decimal Point (Flot..dp)----------- 37

Scaling the PV Display Values (sCale)-------------- 38

Scale Menu ------------------------------------------------- 38

Setting Up the Displays (dsplay setup)------------- 39

Display Line 1 Parameters (Line 1 dsplay)------ 39

Display Line 2 Parameters (Line 2 dsplay) ------ 39

Display Intensity (d-IntY)------------------------------- 39

Display Line 1 Menu (Line 1 dsplay)-------------- 40

Display Line 2 Menu (Line 2 dsplay)-------------- 41

Setting the Tags (tAg) & Units (units)-------------- 42

Application Example 1 ----------------------------------- 42

Application Example 2 ----------------------------------- 45

Setting the Relay Operation (relay) ------------------ 46

Relay Setup Menu (relay setup) ------------------- 46

Setting the Relay Action (act 1) ------------------------ 47

Programming Set (set) & Reset (rst) Points-------- 47

Setting Fail-Safe Operation (failsf)-------------------- 47

Programming Time Delay (delay) --------------------- 47

Relay Action for Communications Break (break)-- 48

Relay Action for Loss of 4-20 mA Input (Loop Break)

----------------------------------------------------------------- 48

Relay and Alarm Operation Diagrams---------------- 48

High Alarm Operation (Set > Reset)------------------ 48

Low Alarm Operation (Set < Reset) ------------------ 48

High Alarm with Fail-Safe Operation (Set > Reset)

----------------------------------------------------------------- 49

Low Alarm with Fail-Safe Operation (Set < Reset)49

Pump Alternation Control Operation------------------ 49

Relay Sampling Operation------------------------------ 50

Relay Operation After Communications Break ---- 50

Signal Loss or Loop Break Relay Operation ------- 51

Time Delay Operation------------------------------------ 51

Relay Operation Details----------------------------------- 52

Overview----------------------------------------------------- 52

Relays Auto Initialization -------------------------------- 52

Fail-Safe Operation (failsf) -------------------------- 52

Front Panel LEDs ----------------------------------------- 52

Latching and Non-Latching Relay Operation------- 53

Non-Latching Relay (Auto) ----------------------------- 53

Non-Latching Relay (A-man)------------------------- 53

Latching Relay (LatcH) ---------------------------------- 53

Latching Relay (Lt-Clr)--------------------------------- 53

Acknowledging Relays----------------------------------- 54

Pump Alternation Control Applications (Altern)-- 54

Setting Up the Interlock Relay (Force On) Feature55

Scaling the 4-20 mA Analog Output (Aout)--------- 56

Setting Up the Password (pass)------------------------ 57

Protecting or Locking the Scanner-------------------- 57

Making Changes to a Password Protected Scanner

----------------------------------------------------------------- 57

Disabling Password Protection ------------------------ 57

Advanced Features Menu -------------------------------- 58

Advanced Menu Navigation Tips---------------------- 58

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Advanced Features Menu & Display Messages---59

Scan Function (SCan)-------------------------------------61

Control Menu (Contrl)-----------------------------------61

Noise Filter (filter)-----------------------------------------62

Noise Filter Bypass (bypass)---------------------------62

Rounding Feature (round) ------------------------------62

Select Menu (SELect)------------------------------------62

Analog Output Source Programming (aoutpr) ----71

User Menu (user) -----------------------------------------72

Digital Input Menu (dI 1)--------------------------------73

Digital Output Menu (dO 1) -----------------------------73

Reset Menu (reset)--------------------------------------73

4-20 mA Output Calibration-----------------------------74

Input Calibration Menu (ICAL)---------------------------75

Recalibrating the Analog Input Channels (Ch-A &

Ch-B) ---------------------------------------------------------75

Troubleshooting-----------------------------------------76

Diagnostics Menu (diag)---------------------------------- 77

Determining Software Version ------------------------- 77

Reset Scanner to Factory Defaults ------------------- 77

Testing the Display LEDs ------------------------------- 77

Scanner Operation--------------------------------------78

Front Panel Buttons Operation------------------------- 78

SafeTouch®Buttons---------------------------------------- 79

Function Keys Operation--------------------------------- 79

F4 Operation -------------------------------------------------- 79

Maximum/Minimum Readings--------------------------- 79

Factory Defaults & User Settings---------------------- 80

Service------------------------------------------------------82

Mounting Dimensions ---------------------------------82

EU Declaration of Conformity-----------------------83

Table of Figures

Figure 1. Transmitter Supply Voltage Selection

---------------------------------------------------------- 14

Figure 2: Integrated ProVu Required

Connections ---------------------------------------- 15

Figure 3. Connector Labeling for Fully Loaded

PD6080/6081---------------------------------------- 16

Figure 4. Power Connections ----------------------- 16

Figure 5: ProtEX-MAX Connections to a Serial

Converter-------------------------------------------- 17

Figure 6. Three-Wire RS485 Connection -------- 17

Figure 7: RS-485 Wiring------------------------------- 18

Figure 8: RS-485 Two-Wire Multi-Drop Wiring- 18

Figure 9. F4 Digital Input Connections----------- 19

Figure 10. Relay Connections ---------------------- 19

Figure 11. AC and DC Loads Protection--------- 20

Figure 12. Low Voltage DC Loads Protection - 20

Figure 13. 4-20 mA Output Connections --------20

Figure 14. Interlock Connections ------------------21

Figure 15. Transmitters Powered by Internal

Supply ------------------------------------------------21

Figure 16. Transmitter Powered by Ext. Supply

or Self-Powered------------------------------------21

Figure 17. Voltage Input Connections------------22

Figure 18: Digital I/O Connections-----------------23

Figure 19. Acknowledge Relays with F4

Function Key----------------------------------------54

Figure 20. Acknowledge Relays with Digital

Input ---------------------------------------------------54

Figure 21: Enclosure Dimensions –Front View

----------------------------------------------------------82

Figure 22: Enclosure Dimensions –Side Cross

Section View----------------------------------------82

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Introduction

The ProtEX-MAX PD8-6080 Super Snooper Modbus®scanner offers all the functionality of the

ProVu PD6080 as a fully FM, CSA, ATEX, and IECEx approved explosion-proof product. It can

be programmed as a Modbus RTU Master, Slave, or Snooper. It is capable of scanning up to 16

variables generated by any Modbus device, which makes it ideal for tank level monitoring and

control. Its superluminous LED digits make it easily readable in smoke, dust, fog, and, with the

optional SunBright® display, even direct sunlight. The PD8-6080 displays in decimal format,

while the PD8-6081 displays in Feet & Inches.

As a master, the PD8-6080/1 reads up to 16 slave devices, scales the data from each, displays

the result, and operates the internal relays and 4-20 mA output. The PD8-6080/1 in Master

mode is capable of polling up to 16 process variables (PVs); it displays all the enabled PVs in

sequence, at a user programmable scan rate; it also allows other PD8-6080/1s in Snooper

mode to read any of the variables being polled by the master. As a snooper, the PD8-6080/1

listens to the Modbus traffic and picks up a specific register or registers being polled by a

master device from a specific slave device and processes the data being read. As a slave, it is

controlled by a master device. The data sent to it by the master is scaled, displayed, and used

to operate the relays and 4-20 mA output.

Data is displayed on an adjustable intensity, dual-line, six-digit display. Its superluminous LED

digits make it easily readable in smoke, dust, fog, and direct sunlight. The upper display is a 0.6

inch, seven-segment LED display, while the lower display digit height is 0.46 inches. The

scanner can be powered from 85-265 VAC or 12-36 VDC. It is available with up to 4 internal

relays and 4 digital inputs/outputs.

The PD8-6080/6081 comes equipped with dual analog input channels (4-20 mA and/or 0-10

VDC) for use in Master Mode. These can be assigned to mA or volts by mapping a PV to the

internal scanner addresses 256-259, depending on the desired function.

Various math functions may be applied to the Modbus and analog inputs including addition,

difference, absolute difference, average, weighted average, multiplication, division, minimum,

maximum, draw, ratio, and concentration. This is in addition to the signal input conditioning

functions (linear, square root, programmable exponent, or round horizontal tank calculations).

The displays, relays, and the analog outputs may be assigned to PVs or to math channels C1,

C2, C3, or C4. The digital inputs/outputs can be custom-programmed for specific operations. A

digital input (F4) is standard.

Free ScanView software allows the Modbus Scanner to be programmed directly from a PC

using the onboard USB connection. Configure multiple scanners, conveniently monitor critical

information, and Datalog right from a PC with ease, further increasing plant efficiency.

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Ordering Information

Standard Display Models

85-265 VAC Power

Model

12/24 VDC Power

Model

Options Installed

PD6080-6H0

PD6080-7H0

No options

PD6080-6H7

PD6080-7H7

4 relays & 4-20 mA output

Feet & Inches Display Models

PD6081-6H0

PD6081-7H0

No options

PD6081-6H7

PD6081-7H7

4 relays & 4-20 mA output

WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Accessories

Model

Description

PDA1485

RS-485 serial adapter - (Included with PD6080 and PD6081)

PDA7485-I

RS-232 to RS-422/485 isolated converter

PDA8485-I

USB to RS-422/485 isolated converter

PDX6901

Suppressor (snubber): 0.01 µF/470 , 250 VAC

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Specifications

Except where noted all specifications apply to operation at +25°C.

Operating Modes

Master

Processes data read from Modbus RTU

slave devices. It polls up to 16 process

variables from 1 to 16 slave devices. The

Master is capable of scanning the selected

PVs, scaling the data, triggering relays,

performing math operations, and driving the

analog outputs.

Snooper

Listens to the Modbus traffic and picks up a

specific register or registers being polled by

a master device from a specific slave device

and processes the data being read. The

Snooper mode handles the data the same

way as the Master.

Slave

Processes data sent to it from a Modbus

RTU master device.

Note: The relays and the 4-20 mA outputs are functional in

all modes.

Master & Snooper Settings

PV Number

PV1–PV16 Enable or disable the process

variables to be polled by the Master.

Slave Id

Assign the slave ID or address (1-247, 256-

259 for mA or volts inputs) containing the

process variables to be displayed by the

selected PV.

Function

Code

Selectwhich Modbusfunction code(03, 04, or65)

tousein readingtheslavedevice.

Number

5 digit: 30001-39999, 40001-49999, or 1-

65,536

6 digit: 300001-365536 or 400001-465536

(Function Code 65 N/A here)

Specifies which register(s) to read in the

slave device. Range is dependent on

Function Code selection (65, 04, or 03) and

digits selection (5 or 6).

Data Type

Select the data format that the slave device

uses. Select between Short integer (2 byte),

Long integer (4 byte), or floating point (4

byte), Signed or Unsigned (integer only) and

byte order: 1234, 4321, 2143, or 3412 (big-

endian vs.

little-endian, or swapped).

Poll Time

1.0 to 99.9 sec. Time between read-

commands (Master mode).

Slave

Response

Timeout

0.0 to 99.9 seconds: Time allowed for the

slave to respond before the scanner

generates a communication break condition.

The master polls the slave 3 times before

starting the response timeout timer.

Slave/Snooper mode: Time the scanner will

wait for new data before going into break

condition.

Slave mode: Programming 0 disables the

timeout; the last value received will be

displayed indefinitely.

Communicati

on Break

Displays “brEAK” after the Master has polled

the slave device 3 times and the response

timeout has elapsed. The Snooper and

Slave modes go into break condition after no

new data is received within the response

timeout window. Relays can be programmed

to go on, off, or ignore the break condition.

The analog outputs can be setup to

generate a fixed mA current when a break

condition is detected.

PV Settings

Tag & Units

6-character, independent tag and units for

each PV and math channel

PV Format

PD6080 default: Decimal format

PD6081 default: FT & IN, 1/8th or 1/16th;

decimal format may be selected for bottom

display indication.

Display

Decimal

Point

Up to five decimal places or none: d.ddddd,

dd.dddd, ddd.ddd, dddd.dd, ddddd.d, or

dddddd

Float

Decimal

Point

Select the number of decimals to use for the

floating point data expected from theslaveor

masterdevice(thisisindependentfromthedisplay

decimalpointselection).

Pv & Math

Scaling

All PVs and math channels may be scaled

to represent the input data in any

engineering unit.

Example: Level transmitter = 999.999

inches; to display in Ft-In-1/16th scale input

2 to display 83 Ft –4 In –0/16th.

Display Settings

Scan Mode

Automatic: 1.0 to 99.9 sec

Manual: Front panel or digital inputs

Go on alarm: Continues scanning after an

alarm is detected

Stop on alarm: Goes to the alarmed PV and

stops scanning; press Scan to resume

scanning.

Display

Scan Rate

Master/Snooper: 1 PV/second to 1 PV every

99.9 seconds

Slave: Dependent on master device (e.g.

PLC)

Note: The display scan rate is independent

of the poll time.

Display

Assignment

Display line 1 may be assigned to PV

(process values), Ch-C (math channel), PV

& units, tag & PV, tag-PV-units, C & units,

tag-C-unit, Set point 1-4, max/min PV,

max/min C.

Line 2 may be assigned to all of the above,

tag, tag & units, or off.

The tag and units are displayed alternately

for 2 sec max, when selected.

Different tags & PVs may be selected to

display on line 1 & 2 at the same time.

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Math Functions

Name

Math Operation (Examples)

(P = Adder, F = Factor)

Setting

Addition

(PV1+PV2+P)*F

Sunm

Difference

(PV1-PV2+P)*F

diF

Absolute

difference

((Abs(PV1- PV2)+P)*F

diFAbS

Average

(((PV1+PV2)/2)+P)*F

AvG

Multiplication

((PV1*PV2)+P)*F

Nmulti

Division

((PV1/PV2)+P)*F

divide

Max PV

Max value of all selected PVs

Hi-pv

Min PV

Min value of all selected PVs

Lo-pv

Draw

((PV1/PV2)-1)*F

drAuw

Weighted

average

((PV2-PV1)*F)+PV1

uwavg

Ratio

(PV1/PV2)*F

Ratio

Concentration

(PV1/(PV1+PV2))*F

Concen

Math 2

Math on other math channels

Nmath2

Programmable

Constants

Constant P (Adder): -99.999 to 999.999,

default: 0.000

Constant F (Factor): 0.001 to 999.999,

default: 1.000

Serial Communications

Compatibility

EIA-485

Connectors

Removable screw terminal connector

Max Distance

3,937' (1,200 m) max

Status

Indication

Separate LEDs for Power (P), Transmit

(TX), and Receive (RX)

Scanner Id

1 –247 (Scanner Modbus address)

Baud Rate

300 –19,200 bps

Transmit

Time Delay

Programmable 0 to 4999 ms

This is the time the scanner will wait for a

slave to respond before sending another

request on the bus. This value should be

greater than 100 ms to avoid collisions on

the bus.

Data

8 bits (1 start bit, 1 or 2 stop bits)

Parity

Even, Odd, or None with 1 or 2 stop bits

Byte-To-Byte

Timeout

0.01 –2.54 second

Turn Around

Delay

Less than 2 ms (fixed)

Note: Refer to the PROVU®Scanner Modbus Register

Tables located at www.predig.com.

General

Input/output

Modbus RTU over RS-485, Two analog

inputs (4-20 mA, 10 V)

Display

Line 1: 0.60" (15 mm) high, red LEDs

Line 2: 0.46" (12 mm) high, red LEDs

6 digits each (-99999 to 999999), with lead

zero blanking

Display

Intensity

Eight user selectable intensity levels

Overrange

Values greater than 999999 cause the

display to flash 999999

Underrange

Values less than -99999 cause the

display to flash -99999

Programming

Methods

Four front panel buttons, digital inputs, PC

and ScanViewsoftware, or Modbus

registers.

Max/Min

Display

Max/min readings are stored until reset by

the user or when power to the scanner is

turned off. User can reset by front panel

pushbuttons, digital input, or via Modbus

registers.

Password

Three programmable passwords restrict

modification of programmed settings.

Pass 1: Allows use of function keys and

digital inputs

Pass 2: Allows use of function keys, digital

inputs and editing set/reset points

Pass 3: Restricts all programming, function

keys, and digital inputs.

F4 Digital

Input Contacts

50k ohm pull-up to 3.3 VDC.

Connect normally open contacts across F4

to COM.

F4 Digital

Input

Logic Levels

Logic High: 3 to 5 VDC

Logic Low: 0 to 1.25 VDC

Non-Volatile

Memory

All programmed settings are stored in non-

volatile memory for a minimum of ten

years, with or without power.

Power

Options

85-265 VAC 50/60 Hz, 90-265 VDC, 20 W

max or 12/24 VDC 10%, 15 W max

Powered over USB for configuration only.

Fuse

Required external fuse: UL Recognized, 5

A max, slow blow; up to 6 scanners may

share one 5 A fuse

Isolated

Transmitter

Power Supply

Terminals P+& P- : 24 VDC10%.

Selectable for24, 10, or 5VDC supply

(internal jumperJ4).All models transmitter

supplyrated @ 25mAmax.

Isolation

4 kV input/output-to-power line. 500 V

input-to-output or output-to-P+ supply

Overvoltage

Category

Installation Overvoltage Category II: Local

level with smaller transient overvoltages

than Installation Overvoltage Category III.

Environmental

T6 Class operating temperature range Ta

= -40 to 60°C

T5 Class operating temperature range Ta

= -40 to 65°C

Max Power

Dissipation

Maximum power dissipation limited to

15.1 W.

Connections

Screw terminals accept 12 to 22 AWG wire

Enclosure

Explosion-proof die cast aluminum with

glass window, corrosion resistant epoxy

coating, color: blue.

NEMA 4X, 7, & 9, IP68.

Default conduit connections: Four ¾" NPT

threaded conduit openings and two ¾"

NPT metal conduit plugs with 12 mm hex

key fitting installed. Additional conduit

opening configurations may be available;

verify quantity and sizes on specific device

labeling during installation.

Mounting

Four slotted flanges for wall mounting or

NPS 1½" to 2½" or DN 40 to 65 mm pipe

mounting. See Mounting Dimensions on

page 82.

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Tightening

Torque

Screw terminal connectors: 5 lb-in (0.56

Nm)

Overall

Dimensions

6.42" x 7.97" x 8.47" (W x H x D)

(163 mm x 202 mm x 215 mm)

Approximate

Shipping

Weight

16.0 lbs (7.26 kg)

Warranty

3 years parts and labor

Relays

Rating

4 SPDT (Form C) internal and/or 4 SPST

(Form A) external; rated 3 A @ 30 VDC

and 125/250 VAC resistive load; 1/14 HP

(≈50 W) @ 125/250 VAC for inductive

loads

Noise

Suppression

Noise suppression is recommended for

each relay contact switching inductive

loads.

Electrical

Noise

Suppression

A suppressor (snubber) should be

connected to each relay contact switching

inductive loads to prevent disruption to the

microprocessor’s operation.

Recommended suppressor value:

0.01 µF/470 , 250 VAC (PDX6901).

Deadband

0-100% of span, user programmable

High or Low

Alarm

User may program any alarm for high or

low trip point.

Unused alarm LEDs and relays may be

disabled (turn off).

Relay

Operation

Automatic (non-latching)

Latching (requires manual acknowledge)

Sampling (based on time)

Pump alternation control (2 to 4 relays)

Off (disable unused relays and enable

Interlock feature)

Manual on/off control mode

Relay Reset

User selectable via front panel buttons,

digital inputs, or PC

1. Automatic reset only (non-latching),

when the input passes the reset point.

2. Automatic + manual reset at any time

(non-latching)

3. Manual reset only, at any time

(latching)

4. Manual reset only after alarm condition

has cleared (L)

Note: Front panel button or digital input

may be assigned to acknowledge

relays programmed for manual reset.

Time Delay

0 to 999.9 seconds, on & off relay time

delays

Programmable and independent for each

relay

Fail-Safe

Operation

Programmable and independent for each

relay.

Note: Relay coil is energized in non-alarm

condition. In case of power failure,

relay will go to alarm state.

Auto

Initialization

When power is applied to the scanner,

relays will reflect the state of the input to

the scanner.

Isolated 4-20 mA Transmitter Output

Output Source

PV1-16, math channels C1-4, set points 1-

4, or manual control mode

Scaling Range

1.000 to 23.000 mA for any display range

Calibration

Factory calibrated: 4.000 to 20.000 = 4-20

mA output

Analog Out

Programming

23.000 mA maximum for all parameters:

Overrange, underrange, max, min, and

break

Communications

Break

Programmable mA output when a slave

device does not reply within the response

timeout.

Accuracy

± 0.1% of span ± 0.004 mA

Temperature

Drift

0.4 µA/C max from 0 to 65C ambient, 0.8

µA/C max from -40 to 0C ambient.

Note: Analog output drift is separate from

input drift.

Isolated

Transmitter

Power Supply

Terminals I+& R: 24VDC 10%.May be

used to power the 4-20 mA output or other

devices. Refer to Figure 3 on page 16 and

Figure 13 on page 20.

All models@ 25mAmax.

External Loop

Power Supply

35 VDC maximum

Output Loop

Resistance

Power supply

Minimum

Maximum

24 VDC

10 

700 

35 VDC (external)

100 

1200 

Digital Inputs & Outputs

Channels

4 digital inputs & 4 digital outputs

Digital Input

Logic High

3 to 5 VDC

Digital Input

Logic Low

0 to 1.25 VDC

Digital Output

Logic High

3.1 to 3.3 VDC

Digital Output

Logic Low

0 to 0.4 VDC

Source

Current

10 mA maximum output current

Sink

Current

1.5 mA minimum input current

+5 V

Terminal

To be used as pull-up for digital inputs

only.

Connect normally open pushbuttons across

+5 V & DI 1-4.

WARNING

DO NOT use +5 V

terminal (pin 1) to power

external devices.

Function

Assignment

The on-board digital inputs (1-4) are

designed to mimic the behavior of the front

panel buttons (Menu, F1, F2, & F3).

If you wish to change their behavior, re-

assign F1-F3 to the desired function, then

change the corresponding digital input to

match.

ProtEX PD8-6080/PD8-6081 Explosion-Proof Modbus® Scanner Instruction Manual

Dual Process Input

Two Inputs

Two non-isolated analog inputs, each

separately field selectable:

0-20 mA, 4-20 mA; 10 V (0-5, 1-5, 0-10 V)

PV Analog

Channel ID

Ch-A mA: Assign PV to ID 256 or Ch-A volt:

257;

Ch-B mA: Assign PV to ID 258 or Ch-B volt:

259

Accuracy

±0.03% of calibrated span ±1 count, square

root & programmable exponent accuracy

range: 10-100% of calibrated span

Temperature

Drift

0.005% of calibrated span/C max from 0 to

65C ambient,

0.01% of calibrated span/C max from -40 to

0C ambient

Signal Input

Conditioning

Linear, square root, programmable exponent,

round horizontal tank volume calculation

Multi-Point

Linearization

2 to 32 points for PV1 and PV2

Programmabl

e Exponent

1.0001 to 2.9999

Low-Flow

Cutoff

0-999999 (0 disables cutoff function) for PV1

and PV2

Calibration

Range

Input

Range

Minimum Span

Input 1 & Input 2

4-20 mA

0.15 mA

10 V

0.01 V

An error message will appear if the input 1 &

input 2 signals are too close together.

Input

Impedance

Voltage ranges: greater than 500 k

Current ranges: 50 - 100 (depending on

resettable fuse impedance)

Input

Overload

Current input protected by resettable fuse, 30

VDC max.

Fuse resets automatically after fault is

removed.

HART

Transparency

Analog input will not interfere with existing

HART communications on the wired 4-20 mA

signal

MeterView Pro

System

Requirements

Microsoft®Windows®XP/Vista/7/8/10

Communications

USB 2.0 (Standard USB A to Micro USB

Configuration

Configure device settings one at a time

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escáner de PRECISION DIGITAL

PRECISION DIGITAL

PRECISION DIGITAL Minimux II PD138 Manual de usuario

PRECISION DIGITAL

PRECISION DIGITAL ProVu Series Manual de usuario

PRECISION DIGITAL

PRECISION DIGITAL PROVU PD6088 Modbus Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario