PRASTEL EASYKW Manual de usuario
Easy BKW klavier quick guide voor gebruik icm SK-ACP E centrale :
-In programmatie gaan –
oduw de # toets gedurende 2s –Transmit LED gaat uit en Program
LED wordt Rood
oduw je 4cijferige programmatiecode (fabrieksinstelling 1234)
oindien ok wordt Program Led groen
oOm uit programmatie te gaan: duw de # waarna de Program Led
uitgaat & Transmit LED groen wordt
-Selecteer transmissieformaat:
oGa in programmatiemodus
oDuw 1 om Menu1 in te gaan –de transmit LED wordt rood
oDuw de gewenste optie transmissieformaat –druk 5 voor 26bits
Wiegand formaat met 1- tot 5-cijferige codes (default facility code
setting is 000)
Bij ingave door klant voor code korter dan 5 nummers moet
de # toets ingedrukt worden om het eind van het codenr. aan
te geven.
-Verander de progammatiecode
oGa in programmatiemodus
oDuw 3 om menu3 in te gaan –de transmit LED wordt rood
oGeef de nieuwe 4-digit code in die u wil gebruiken als
programmatiecode –u hoort 1 biep
De program led gaat uit
De transmit led wordt rood
Voor verdere details zie handleiding Easy BKW.
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
1
1. INTRODUCTION
The EASYKW is a vandal resistant programmable keypad reader. The
Wiegand output allows the connection to a large number of access
control devices.
Model EASYBKW is provided with LED backlight.
2. MAIN TECHNICAL FEATURES
Operating Voltage Range: 5 – 16 Vcc
Maximum Input Current: 20mA in standby (60mA max.)
With backlight
(EASYBKW only): 50mA in standby (90mA max.)
Transmission formats:
1 to 5 cifre + Facility Code, 26-Bit Wiegand
30-bit Wiegand
clock & data
Operating Temperature: -31°C to 63°C
Umidity operating : 0 a 95% (Non-Condensing)
IP protection degree: IP67
Dimensions: 120mm x 76mm x 27mm
Weight: 410 g
3. MOUNTING
Before starting, select the location to mount
the EASYKW reader. This location should be
at
shoulder
height. For
fixing, drill
four holes,
in correspondence of the four points marked
as B.
Route the interface cable from the Reader to
the Controller. Fix the EASYKW back cover
to its mounting location and return the front
cover by using the supplied security screw
and the L-Shaped tool provides in the controllers accessories kit.
A
A
BB
BB
C
CAUTION! DO NOT DRILL
This is the Tam
p
er Lens
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
2
4. WIRING
The reader is supplied with a 6-conductor cable about 40 cm., to
connect the Reader, perform the following steps:
1) Prepare the Reader cable by cutting the cable jacket back 3 cm
and strip the wire 1,5 cm. Prepare the Controller cable at the
same way.
2) Splice the Reader pigtail wires to the corresponding Controller
wires and cover each connection.
COLOR OUTPUT
RED +VDC
BLACK GND
WHITE DATA1 / CLOCK
GREEN DATA0 / DATA
BROWN LED CONTROL
PURPLE TAMPER
3) If the tamper output is being utilized, connect the purple wire to
the correct input on the Controller.
4) Trim and cover all conductors that are not used.
5. TRANSMIT MODE
When the EASYKW is in Transmit Mode, it is ready to receive data
from an entered PIN code.
In this mode the Transmit LED is red
and the Program LED is off.
During a code transmission the
Transmit LED will flash green. Keyboard data can be sent via one of
different Keypad Transmission Formats (see par. 6.3)
RED
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
3
6. PROGRAMMING THE EASYKW
Programming the EASYKW is done solely via the unit's keypad driven
Programming Menu System (see par. 6.1).
During the EASYKW's manufacturing process certain codes and
settings are pre-programmed. These settings are the called the
"Default Factory Settings".
The table below shows the names of all the EASYKW Menus.
Menu Description Menu
number
Selecting keypad transmission format 1
Changing the programming code 3
Changing the facility code 4
Return to Factory Default Settings 0
6.1 Entering Programming Mode
1) Press the "#" key for 2 seconds. Transmit LED will turn off and
Program LED will turn red.
2) Enter your 4-digit
Programming Code.
3) If the Programming Code
is valid the door LED will
turn green and the
EASYKW will be in
Programming Mode.
Note: The factory default
Programming Code is 1234. If a
Programming Code is not
entered within 30 sec., the
keypad will return to Transmit Mode.
RED
GREEN
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
4
6.2 Exiting Programming Mode
1) To exit the Programming Mode at any time: Press the "#" key,
You will hear a beep, The Program LED will be off The Transmit
LED will turn green. This indicates that the EASYKW has
returned to Transmit
Mode.
2) Wrong entries may
reset the reader back
to Transmit Mode.
3) While in Programming Mode if no key is pressed for 30 seconds
the EASYKW will exit Programming Mode and return to Transmit
Mode.
6.3 Selecting Keypad Transmission Format
The EASYKW has eight different
keypad transmission formats to
select from. Follow the steps below
to select the appropriate keypad
transmission format that you wish
to use.
1) Enter Programming Mode
2) Press "1" to enter Menu 1,
the Transmit LED will turn
red.
3) Enter the appropriate option
number for the keypad
transmission format that you
wish to select (see the following table). If an incorrect option
number is entered the reader will return to Transmit Mode and
the keypad transmission format will remain unchanged.
4) System returns to Transmit Mode, you will hear one beep, the
Program LED will turn off the Transmit LED will turn red.
Note: Only one keypad transmission format can be active at any one
time.
GREEN
GREEN
RED GREEN
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
5
See the table below to determine the Option Number for the Keypad
Transmission Format you wish to select.
Keypad Transmission Format Option
Number
1 to 5 keys + Facility Code, 26-bit Wiegand 5
1 to 8 Keys , Clock & Data 8 + n. digit
30-bit Wiegand 9
6.3.1 OPTION 5 -- 1 to 5 Keys + Facility Code, 26-Bit Wiegand
Buffers up to 5 keys and outputs keypad data with a facility code like a
26-Bit card output. The facility code is set in Programming Menu
number four and can be in the range 000 to 254. The factory default
setting for the facility code is 000 (see par. 8 for Setting the Facility
Code).
The keypad PIN code can be one to five digits long and can range
between 1 and 65,535. When entering a keypad PIN code that is less
than 5 digits long, the “#” key must be pressed to signify the end of PIN
code entry. For keypad PIN codes that are 5 digits long, on the fifth
key press of the 5 digit PIN code, the data is sent across the Wiegand
Data lines as binary data in the same format as a 26-Bit Card.
If the “ * “ key or the “#“ key are pressed during PIN code entry or a
PIN code greater than 65,535 is entered, the keypad will clear the PIN
code entry buffer, generate a beep and is ready to receive a new 4
digit keypad PIN code.
If the entry of the 1 to 5 digit keypad PIN code is disrupted and no
number key or “#” key is pressed within 5 seconds, the keypad will
clear the PIN code entry buffer, generate a medium length beep and is
ready to receive a new 1 to 5 digit keypad PIN code.
(EP) FFFF FFFF AAAA AAAA AAAA AAAA (OP)
where: EP = Even parity for first 12 bits.
OP = Odd parity for last 12 bits.
F = 8-Bit Facility Code
A = 24-Bit code generated from keyboard
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
6
6.3.2 OPTION 8 -- 1 to 8 Keys , Clock & Data
Buffers up to 8 keys and outputs keypad data without a facility code
like standard Clock and Data card output. The keypad PIN code can be
one to eight digits long. The PIN code length is selected while
programming the reader for Option 8. The reader will transmit the data
when it receives the last key press of the PIN code. The data is sent
across the two data output lines as binary data in Clock & Data format.
If the “ “ key or the “#“ key are pressed during PIN code entry, the
keypad will clear the PIN code entry buffer, generate a beep and is
ready to receive a new keypad PIN code.
If the entry of the digit keypad PIN code is disrupted and no number
key or “#” key is pressed within 5 seconds, the keypad will clear the
PIN code entry buffer, generate a medium length beep and is ready to
receive a new keypad PIN code.
6.3.3 OPTION 9 -- 1 to 8 Keys , 30-Bit Wiegand
The keypad PIN code can be one to five digits long and can range
between 1 and 16.777.215. When entering a keypad PIN code that is
less than 8 digits long, the “#” key must be pressed to signify the end of
PIN code entry. For keypad PIN codes that are 8 digits long, on the
eighth key press, the data is sent across the Wiegand Data lines as
binary data in the same format as a 30-Bit Card.
If the “*“ key or the “#“ key are pressed during PIN code entry or a PIN code
greater than 16.777.215 is entered, the keypad will clear the PIN code
entry buffer, generate a beep and is ready to receive a new PIN code.
If the entry of the PIN code is disrupted and no number key or “#” key
is pressed within 5 seconds, the keypad will clear the PIN code entry
buffer, generate a medium length beep and is ready to receive a new 1
to 8 digit keypad PIN code.
(EP) RRRR AAAA AAAA AAAA AAAA AAAA AAAA (OP)
where: EP = Even parity for first 14 bits.
OP = Odd parity for last 14 bits.
R = 4-Bit reserved (always 0)
A = 24-Bit code generated from keyboard
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
7
7. Changing the Programming Code
1) Enter Programming Mode
2) Press "3" to enter Menu 3: the
Transmit LED will flash red.
3) Enter the new 4-digit code you
wish to set as the Programming
Code.
You will hear one beep
The Program LED will turn off
The Transmit LED will turn red
NOTE: Programming Code can not
be erased, i.e. the code 0000 is not
valid and will not erase the
Programming Code.
8. Changing the Facility Code
1) Enter Programming Mode.
2) Press "4" to enter Menu 4:
the Transmit LED will flash
orange.
3) Enter the new 3-digit code
you wish to set as Facility
Code.
4) System returns to Transmit
Mode
You will hear one beep
The Program LED will
turn off
The Transmit LED will
turn red
NOTE: Facility codes can be in the
range of 000 to 254.
GREEN
RED GREEN
RED
GREEN
ORANGE GREEN
RED
EASYKW - EASYBKW ENGLISH ISEASYKW_12_04.doc
8
9. Return to Factory Default Settings
Warning:You must be very careful before using this command!
Doing so will erase the entire memory which includes all User and
Special Codes, and return all codes to their factory default
settings.
1) Enter Programming Mode.
2) Press "0" to enter Menu 0
The Transmit LED will
flash red
The Program LED will flash red
3) Enter your 4-digit Programming Code
If the Programming Code is
valid, all memory will be
erased, you will hear three
beeps and the controller will
return to Normal Mode.
If the Programming Code is invalid you will hear a long
beep and the controller will return to Normal Mode
without erasing the memory of the controller.
10. Replacing a lost Programming Code
In the event that the Programming Code is forgotten, the EASYKW
may be reprogrammed in the field using the following instructions:
1) Remove power from the reader
2) Activate tamper by removing the reader from the wall or
removing the reader’s case.
3) Apply power to the reader
4) You now have 10 seconds to enter Programming Mode using
the factory default Programming Code 1234.
GREEN
EASYKW - EASYBKW FRANÇAIS ISEASYKW_12_04.doc
1
1. GENERALITES
EASYKW est un lecteur à clavier programmable antivandale. La sortie
au standard Wiegand permet d’être relier à la plupart des appareils de
contrôle d'accès qui se trouvent sur le marché.
La version EASYBKW est équipée de rétroéclairage.
2. CARACTERISTIQUES TECHNIQUES
PRINCIPALES
Tension d'alimentation: 5 – 16 Vcc
Courant absorbé: 20mA en veille (60mA max.)
Avec rétroéclairage
(seulement EASYBKW): 50mA en veille (90mA max.)
Formats de transmission:
de 1 à 5 chiffres + code site, 26-bit Wiegand
30-bit Wiegand
data clock
Température de fonctionnement: de -31 °C à 63 °C
Fonctionnement avec humidité : 0 à 95% (sans condensation)
Degré de protection IP: IP67
Dimensions: 120mm x 76mm x 27mm
Poids: 410 g
3. INSTALLATION
Avant de procéder à l'installation, choisir
l'emplacem
ent pour le
montage
du clavier
EASYKW. Celui-ci devrait être placé à
hauteur d'épaule et sur le même côté que la
poignée de la porte. Pour fixer le clavier,
percer aux 4 endroits repérés par la lettre B.
Relier le câble de liaison du lecteur au
contrôleur. Fixer le fond de l'appareil dans la
A
A
BB
BB
C
ATTENTION! NE PAS PERCER
Lentille antivandale
Otros manuales para EASYKW
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Controladores de acceso IP de PRASTEL
