Pradotec HRT 500 Manual de usuario
0
1
Table of Contents
KNOWING YOUR DEVICE 3
DEVICE SPECIFICATION 5
BASIC INSTALLATIONS 6
THE BATTERY 6
GUIDELINE FOR INSTALLING SIM/SAM CARD 6
GUIDELINE FOR INSTALLING MICRO SD CARD 7
FIRST TIME USE 8
SCREEN CALIBRATION 8
TIME,DATE AND TIME ZONE CONFIGURATION 8
TOUCH SCREEN OPERATIONS 9
USING THE STYLUS 9
START MENU 10
SHELL TASKBAR 11
SOFTWARE INPUT PANEL (SIP) 12
KEYPAD 13
CUSTOMIZING HRT500 14
LCD BRIGHTNESS CONTROL 15
KEYPAD LIGHT CONTROL 17
POWER 18
DISPLAY 19
MOUSE 20
KEYBOARD 20
2
AUDIO VOLUME 21
STYLUS PROPERTIES 21
NETWORK &DIAL –UP CONNECTION 22
REGIONAL AND LANGUAGE SETTING 22
OWNER PROPERTIES 23
PC CONNECTION 23
STORAGE PROPERTIES 24
SYSTEM PROPERTIES 25
PASSWORD PROPERTIES 25
SCREEN ROTATION 26
TASKBAR &SECURE SHELL 26
INPUT SELECTION PANEL 27
DATE &TIME PROPERTIES 27
INTERNET OPTIONS 28
REMOVE PROGRAMS 28
INTERNET EXPLORER 29
FEATURES 31
WIRELESS LAN (WI-FI)USAGE 31
BLUETOOTH USAGE 33
GSM USAGE 38
USING THE CONTACT CARD READER 41
USING THE CONTACTLESS READER (RFID) 41
USING THE FINGERPRINT SENSOR 42
USING THE BARCODE SCANNER 42
APPENDIX: TROUBLESHOOTING GUIDE 43
RESET THE HRT500 AND CLEAR MEMORY 43
IF HRT500 RUNS OUT OF POWER 44
IF HRT500 RUNS OUT OF MEMORY 45
INACCURATE RESPONSE TO STYLUS TAPS 46
ROUTINE MAINTENANCE 46
BATTERY GUIDELINES 47
TRAVEL GUIDELINES 47
SHIPPING GUIDELINES 48
3
FRONT
Knowing Your Device
4
TOP
BOTTOM
REAR
SIDE
5
Device Specification
Systems
Memory 256MB DDR-2 RAM, 4GB Flash
Memory Expansion 1 x micro-SD Memory Slot (Support up to 32GB)
Device Operating System WinCE 6.0
Host PC Operating System Windows® 7/ Vista/ XP
Programming Language C++ Programming, NET Programming in Microsoft® Visual Studio 2005
Communication Interfaces
Bluetooth Bluetooth Version 2.0
Wireless LAN IEEE 802.11 b/g Wi-Fi
Network 3.5G - W-CDMA, 850, 900, 2100 MHz
GSM/ GPRS/ EDGE (1 X SIM Slot)
USB USB Client 1.1 (ActiveSync)
Human Interfaces
Displays 3.5” (480x640) Transflective TFT Colour Touch Screen
Keypad 12 Alphanumeric Buttons, 3 Function Buttons and 1 Power On/Off Button
LED 1 x Power Status, 1 x Network Status, 1 x Charge status
Speaker Built-in Mono Speaker
Power
Battery 7.4V 1800mAH Li-ion Battery
Operating Time 4 - 6 Hours
Mechanical
Dimension (LxWxH) mm 197 x 92 x 44
Weight Approximately 600g
Environment
Operating Temperature -10°C to +50°C
Storage Temperature -20°C to +60°C
IP Rating (Water & Dust Protection) IP65
Drop Test 1.5m
Fingerprint Sensor
Sensor Optical sensor
Resolution 500dpi
Active Area (mm) 14 x 22
Supported Template Sagem Algorithm
Template Formats Morpho Proprietary, ISO 19794-2, ANSI/ INCITS 378, RAW/Bitmap,
WSQ (Optional)
Contact Card Reader
Standard ISO/IEC 7816 Part 1, 2, 3, (T=0, T=1)
Card Slot 1 x ID-1 Card Slot
3 x ID-0 SAM Slots
Communication Speed 9.6 kbps up to 115.2kbps
Card Type Class A & B
Contactless Reader
Standard ISO/IEC 14443 A/B Part 1, 2, 3, 4
Card Type MiFARE Classic / Ultralight / Ultralight C /Desfire / MiFARE Plus / Sony
Felica / HID i-class
Card Transmission Rate Up to 848 kbps (Card Type Dependant)
Camera
Resolution 5 Megapixels (LED Flash)
6
The Battery
The battery has been partially charged at the factory, however please charge it for 4 hours
before switching on the device for the first time.
Guideline for Installing SIM/SAM card
WARNING
Keep all SIM cards out of the reach of children.
The SIM card and its contacts can be easily damaged by scratches or bending.
Be careful when handling, inserting or removing the card.
Before installing the SIM card, always make sure that the device is fully charged as the
application will not work properly with insufficient amount of power.
To insert SIM card
1) Close all programs and switch off the device.
2) Remove the hand strap.
3) Unlock both wing lock.
4) Remove the Battery cover.
5) Remove the Battery pack.
6) Unlock the SIM Slot and pull back the cover for insertion.
7) Ensure that the cut corner faces top right and the gold contacts of the card is facing
downwards into the device.
SAM A
SAM B
SAM C
SIM
(Slot 0)
(Slot 2)
(Slot 3)
Basic Installations
7
8) Push down the SIM slot cover and slide outward to lock it.
9) Place the battery back followed by battery cover.
10) Push the wing lock to secure the battery cover and finally install the hand strap back
into the hand strap tab.
To insert SAM card
1) Insert the SAM cards into slot 0, 2, 3.
2) Insertion steps are the same as SIM card insertion steps.
3) SAM card is for internal security.
Guideline For Installing Micro SD Card
1) Close all the programs and switch off the device.
2) Remove the hand strap.
3) Unlock both wing lock.
4) Remove the battery cover.
5) Remove the battery pack.
6) Unlock the Micro SD slot and pull back the cover until easy for insertion.
7) When inserting the Micro SD card, ensure that the gold contacts of the card is
facing downwards into the device
8) Push the Micro SD slot cover down and slide inward to lock it.
9) Place the battery back followed by battery cover.
10) Push the wing lock to secure the battery cover and finally install the hand strap back
into the hand strap tab.
Micro SD
8
Screen Calibration
Once the charging has completed, turn on the device by pressing the power button.
On the first time basis, it is advisable to calibrate the screen by going to:
Start -> Settings -> Control Panel -> Stylus.
Follow the cursor and tap on it. Kindly set the Time, Date and Time Zone as the default time,
date and time zone differ from place to place.
Time, Date and Time Zone configuration
Go to Start -> Settings -> Control Panel -> Date/Time to set the Time, Date and Time
Zone.
First Time Use
Carefully press and briefly hold the
stylus on the centre of the target.
Repeat as the target moves around
the screen. Press ESC key to cancel
9
The following defines the various operations that the user can perform with the stylus.
Tap
Tap once to select a program
Double Tap
Tap the item twice to open or execute a program
Drag
Hold the stylus on the screen to drag objects
The stylus is housed inside the stylus holder at the right corner of the device.
IMPORTANT
Avoid misplacing the stylus by always storing it in the stylus holder when not in use.
Avoid breaking the tip of the stylus.
Use only the stylus that comes with the HRT500 or some other stylus type instrument
with a soft, blunt point to perform touch screen operations. Never use a pen, pencil, or
other sharp writing element.
Touch Screen Operations
Using the Stylus
Tabla de contenidos
