Powertrain V1200 Manual de usuario

ELECTRIC TREADMILL –MODEL V1200

INSTRUCTION MANUAL

Please read these instructions carefully before use and keep for future reference

FOR DOMESTIC INDOOR USE ONLY

WARNING: Keep young children away from this machine at all times. Contact with the

moving surface may result in severe friction burns.

1. CAUTION

To avoid injuries please read this manual carefully before using the treadmill.

Before starting any exercise program you should consult your doctor

Ensure you have tightened all the bolts and nuts on this machine before commencing any

exercise

Do not stand on running belt whilst starting the unit

Stop immediately if you feel unwell or nauseous

Adjust speed slowly

Do not adjust the belt while the unit is in use

It is recommended that you wear sports shoes and appropriate clothing when using the

treadmill

Children, elderly, pregnant women and people with medical conditions should not use the

treadmill unless authorized by their doctor and in the presence of an adult who may assist

Clip the safety key on your clothing during use

Keep the safety key away from children when the treadmill is not in use as it may present a

choking hazard or allow them to activate the unit

Keep silicone oil away from children’s reach. If accidentally swallowed or it comes into

contact with eyes, use water to wash out and immediately seek medical assistance

2. SAFETY NOTICE

Operate the machine on sturdy flat ground only.

Do not use the machine in the following situations:

oOutdoors. (The machine is designed for indoor use only)

oUneven or unlevel surfaces

oSunlit area or near a heat source

This machine requires a constant 220-240V AC power connection

An error may be displayed if power is not stable. Do not share power points with other

equipment

Be careful of children or other objects while folding and unfolding the machine

Do not store or use the machine near wet areas or on slippery or wet surfaces, this will

damage the machine and void the warranty

3. CAUTION PRIOR TO USE

Do not use the machine if you are unwell and immediately stop using the machine if you

start feeling unwell whilst using it.

Disconnect the machine from power when not in use.

Prior to relocating or folding the machine, disconnect it from power.

Machine is to be used on a flat surface only.

Ensure a 2m clearance around the machine is available prior to using it.

Do not start the machine when it is folded.

Keep all liquids away from the machine as they will damage the unit and void all warranty.

Machine is not to be used in poorly ventilated spaces or locations with flammable objects

in its vicinity.

Do not put any objects on the machine.

Switch off all functions and disconnect from power when not in use.

Please do not stand directly on the belt while starting the machine.

Do not disassemble the machine without a written authorization from the manufacturer

Ensure the running belt is fastened before use

4. PRODUCT SPECIFICATIONS

Main Specifications and Parts List

Main Specifications

No.

Parameters Names

Description

Input power voltage

AC220-240V(50/60Hz)

Motor power

3.0HP

Speed

1-20Km/h

Packing list

No.

Name

Units

Qty

Treadmill Unit

set

Screws bag list

NO.

Name

QTY

NO.

Name

QTY

Inner hexagon spanner 6mm

MP3 cable

Inner hexagon spanner 5mm

Screw M8*22

Silicone Oil

Screw M8*52

User Manual

Screw M8*25

Safety Key

Power Line

5. ASSEMBLY INSTRUCTIONS

During assembly, first insert and moderately tighten screws and when the frame has been

fully assembled, inspect all the screws and tighten them completely.

Lay unit flat on the ground. Cut the nylon cable ties (where supplied) on the base. Lift the

upright columns and console in the direction shown in the diagram below.

WARNING: THIS PRODUCT IS HEAVY. ENSURE TWO PEOPLE ARE ASSEMBLING IT AT ALL TIMES

Use the inner hexagon spanner (#5) and insert screws M8*52 and screws M8*22 to

attach the columns to the base of the treadmill as shown:

Use an inner hexagon spanner (#5) and screw M8*25 to fix the console to the columns.

Use a screwdriver and insert M5*14 to fix the base corner covers to the columns, as shown

in the below diagram.

Remove the console and connect the cables as shown:

CAUTION: Ensure cables are not pinched or jammed as it will damage the unit and void warranty.

Place the exposed surplus cabling inside the case and mount the console on to the console slot.

Adjust the position/angle. Insert screws M8*25 and tighten them as shown:

Position the safety key in the correct position as shown below.

Safety Key Function

oDisconnecting the safety key will immediately stop the running track and the screen

will display “E7”, and the treadmill will emit a beep.

oPlacing the safety key back on the designated area on the console will clear all data

in 2 seconds.

CAUTION: Ensure all screws are correctly tightened according to the requirements and

check no part has been left out prior to connecting to power.

6. USING THE TREADMILL

Power on –Connect the power adapter to a power point and turn on the unit by

using the red switch. The LED will illuminate, and the treadmill will emit a beeping sound.

The screen on the control panel will switch on.

Start - starts after 3 second countdown.

Stop –Pressing the Stop key will gradually stop the treadmill.

Program There are 12 pre-set programs, press the “PROGRAM” button to toggle between

them.

Mode - In standby mode pressing the Mode key will cycle through 3 modes:

1) Time Countdown 2) Distance Countdown 3) Calorie Countdown

Speed Presets -In running mode using these shortcuts will change the running speed

accordingly to 3, 6, 9, and 12km/h

Speed+ / Speed-

oIn running mode these keys are used to adjust the speed up and down

Incline Presets - In running mode these keys are used as shortcuts to set incline levels

to 3%, 6%, 9%, and 12%

Incline+ / Incline-: In running mode these keys will adjust the incline level up and down

Vol+ / Vol- Use these keys to adjust volume when playing music in USB mode

Control Dial

A: When stopped, rotate the control to GO and press, the treadmill will start

B: While running press the control to pause, press again to resume

C: While running rotate the control to increase and decrease the speed

D: While paused, press and hold for 3 seconds to stop the treadmill

(when the treadmill is decelerating the control is inoperative)

Display Functions:

1. SPEED: Shows current value of speed

2. TIME: Shows current time value of exercise or the value of time countdown for

the PROGRAM or MODE

3. DISTANCE: Shows current distance value of exercise or the value of distance countdown

for MODE

4. CALORIES: Shows current calories value of exercise or the value of calories countdown for

MODE

5. HEART RATE: Shows the value of heart rate after a few seconds holding the heart rate

sensors.

NOTICE: The heart rate function is to be used as an exercise reference feature only and is

not to be relied on for accurate heart rate assessment and is not to be used for medical

purposes. Should you feel unwell, stop exercising immediately and contact your doctor.

Preset Programs:

Time

Program

Set time/10=Running time of each segment

Speed

Incline

Speed

Incline

Speed

Incline

Speed

Incline

Speed

Incline

Speed

Incline

Speed

Incline

Speed

Incline

Speed

Incline

P10

Speed

Incline

P11

Speed

Incline

P12

Speed

Incline

Error Codes

Error code

Description

Solution

Bad Connection: when the

power is on, the connection

between lower controller and

the console is abnormal.

Possible Cause: the electrical connection between the lower

controller and console is faulty, check each joint between the

controller and console, make sure that each cable is fully plugged

in. Check the connection line, replace it if is damaged.

No signal from motor.

Possible Cause: Check the motor cable to see whether it is

connected well or not, if not, re-connect the motor wire again.

Check the motor cable to see whether it is damaged or has a burnt

smell, if yes, replace the motor.

Current overload

protection:

Whilst in use, the lower

controller detects the current

to be over 6A for more than

3 seconds.

Possible Cause:

Overloading leads to excessive current, and the system stops out of

self-protection, or some part is stuck, causing the motor to stop.

Adjust the treadmill and restart it. Check if there is liquid or burnt

smell while the motor is running, if yes, replace the motor; check if

the controller has a burnt smell, if yes, replace the controller; check

the power supply voltage, if it does not match the specifications,

change into correct voltage and test the machine again.

Explosion-proof impact

protection: the abnormal

voltage or motor cause a

circuit fault which drives the

motor.

Possible Cause:

Check if the power supply voltage is 50% lower than normal

voltage，use the correct voltage and test the machine again；check

if the controller has a burnt smell and replace the controller; Check

if the motor cable is connected and connect the motor wire again.

No safety key

Place the safety key on the correct position on the control panel

7. Maintenance

Warning: Before cleaning or carrying out any maintenance, ensure the treadmill is

disconnected from power

Cleaning will extend the life of your treadmill

Remove dust periodically in order to maintain all parts clean

Be sure to clean running belt with both sides of the exposed portion, which will reduce the

accumulation of impurities

Make sure to wear clean athletic shoes to avoid introducing dirt on to the running board

and belt

Treadmill belts must be cleaned with a damp cloth and mild soap

Ensure none of the components, nor the treadmill itself come into contact with liquids, this

will void the warranty

Warning: Make sure power plug disconnect before moving motor cover away, clean the

dust from the motor and surrounding area at least once a year with a vacuum, do not

use water or damp cloth

Maintenance of the Running Board and Belt - Lubrication and Cooling

Your treadmill's running board and running belt has been lubricated at the factory

Friction between the running belt and running board will impact on the life and

performance of your treadmill

Regular application of treadmill lubricant is required, check the board regularly

To check if the belt needs to be lubricated, simply lift each side of the belt and feel the top

surface of the running deck. If it is slick to the touch, then no lubrication is required. If it is

dry to the touch, then lubricate with silicon oil

To lubricate (where required):

oLift the edge of the running to expose the running deck

oPlace a few drops of silicone oil along the centre of the running deck

oRun the treadmill without the user at a slow speed for 5 minutes

CAUTION: Do not over lubricate. Wipe away excess lubricant from the belt.

If the board’s surface is damaged contact our customer service centre

We recommend applying lubricant between running belt and running board:

oInfrequent user (use less than 3 hours a week) - once per month

oFrequent user (use more than 7 hours a week) - once a fortnight

To safeguard your treadmill and extend the life of the unit it is recommended that after 2

hours of continued use the machine be switched off and allowed to cool for a minimum of

10 minutes before using it again

If the treadmill belt is loose it will skid and slip when running.

If the treadmill belt is too tight it may reduce motor performance and increase wear and

tear of the roller and running belt

Lift each side of the running belt around 50-75mm to check the tension

Adjusting alignment and tightness

The running belt is adjusted at the factory, however after use it may stretch and will require

re-tensioning. For best use it may be required to adjust the running belt for its optimum

alignment

Running Belt alignment

Place treadmill flat on the floor but do not stand on it.

Turn on treadmill and set the speed at 6-8km/hour .

If the running belt is shifting to the right, rotate the right adjusting bolt with 1/2 turn

clockwise, then rotate the left adjusting bolt with 1/2 turn counter-clockwise. (Diagram A)

If the running belt is shifting to the left, rotate the left adjusting bolt with 1/2 turn clockwise,

then rotate the right adjusting bolt with 1/2 turn counter-clockwise. (Diagram B)

Diagram A Diagram B

Tabla de contenidos

Otros manuales de Rueda de andar de Powertrain

Powertrain

Powertrain MX1 Manual de usuario

Powertrain

Powertrain MX2 Manual de usuario

Powertrain

Powertrain K1000 Manual de usuario

Powertrain

Powertrain V1100 Manual de usuario

Powertrain

Powertrain V20 Manual de usuario

Powertrain

Powertrain V30 Manual de usuario

Powertrain

Powertrain V100 Manual de usuario

Manuales populares de Rueda de andar de otras marcas

Treadly

Treadly TREADLY 2 Manual de usuario

HEALTH ONE

HEALTH ONE Walk Ro Manual de usuario

NordicTrack

NordicTrack NTL12941 Manual de usuario

NordicTrack

NordicTrack T7.5 S Manual de usuario

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Manual de usuario

Merax

Merax MS282992 Manual de usuario

FYTTER

FYTTER RU-2SX Manual de usuario

Precor

Precor 903 Manual de usuario

FitLogic

FitLogic freewill d225 Manual de usuario

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Manual de usuario

Horizon Fitness

Horizon Fitness Adventure 5 Plus Manual de usuario

Stamia

Stamia InMotion II Manual de usuario

Smooth Fitness

Smooth Fitness EVO 3i Manual de usuario

NordicTrack

NordicTrack NETL81810.0 Manual de usuario

Schwinn

Schwinn 830/Journey 8.0 Manual de usuario

Keys Fitness

Keys Fitness HealthTrainer HT-740T Manual de usuario

Spirit

Spirit XT8 Manual de usuario

NordicTrack

NordicTrack T 14.0 Treadmill Manual de usuario