PowerPlus Energy Powerlink Instrucciones de funcionamiento
Author: Edwin Cotter Date: 30/09/2021 Ver: 3.1 Page 1 of 7
Powerlink Installation and Operation Guide
Powerlink Setup and Registration Procedure
Author: Edwin Cotter Date: 30/09/2021 Ver: 3.1 Page 2 of 7
Powerlink Installation and Operation Guide
Battery Serial number scanning
Connect the micro USB port from the 5V
power adaptor to the Powerlink port
shown in the picture.
3
Connect the 5V power adaptor to the
main AC power outlet and Switch it ON.
Wait 10 seconds.
2
1
Connect the cable from the LAN modem
(for the internet) to the Powerlink port
shown in the picture.
Note: This port is
next to the 4 USB ports
Author: Edwin Cotter Date: 30/09/2021 Ver: 3.1 Page 3 of 7
Powerlink Installation and Operation Guide
•.
Type the password 12345678
6
Open the web browser. Type the
address 192.168.0.10:8822
It will open the home page as shown in
the picture.
5
4
Open WiFi network menu in mobile or
computer (Interface layout might be
different from the picture). Select PPE-
Powerlink-xxxx (xxxx will be digits)
Press reset data to remove any
previous data from the Files.
9
Enter the Number of Batteries to be
scanned into the box and press
submit.
8
7
Press configuration button, a
screen like the picture will open
Author: Edwin Cotter Date: 30/09/2021 Ver: 3.1 Page 4 of 7
Powerlink Installation and Operation Guide
Battery scanning order should be from top to bottom in the rack.
•Repeat the steps 11 and 12 in every other battery.
•Confirm the number of serial numbers is same as number of batteries in the battery rack.
Take the longest RJ45 cable and
connect the cable into the Powerlink
module side having two RJ45 port.
Note: please make sure, the cable is
connected to the correct port in the
Powerlink
11
12
Connect the other RJ45cable end to the
battery need to be scanned.
Press Scan in the Battery management
screen and after couple of seconds, you
will see battery (BMS) serial number as
in the picture.
10
6
Author: Edwin Cotter Date: 30/09/2021 Ver: 3.1 Page 5 of 7
Powerlink Installation and Operation Guide
Replace the long RJ45 cable with
suitable length RJ45 cable to connect in
the top battery.
14
Connect the other end to top battery in
the rack.
13
Connect another small RJ45 cable to the
remaining port in the same battery.
16
17
Connect the other end into next battery
(Daisy chain).
Repeat the daisy chain connection
till last battery.
15
Author: Edwin Cotter Date: 30/09/2021 Ver: 3.1 Page 6 of 7
Powerlink Installation and Operation Guide
Congratulations!
The battery monitoring configuration procedure is completed
18
Connect the RJ45 termination connector
in the remaining slot on the last battery.
21
After 1-2 minutes, go to MultiStat
(available on the home page).
Verify that all the batteries are responding.
19
20
If you are not able to see the battery
status in MultiStat window, press
Restart polling button in configuration
page and repeat step 19 & 20.
Author: Edwin Cotter Date: 30/09/2021 Ver: 3.1 Page 7 of 7
Powerlink Installation and Operation Guide
Request Login Details for the Portal
The portal URL is: https://performance.powerplus-energy.com.au:3000/login
To gain your login information for the portal, email “support@powerplus-energy.com.au" and provide the following information:
•Subject line: Portal access request
•PowerLink Serial Number
•Site Name
Our support team will then create a login and email it to you the details once complete.
Otros manuales de Hardware de red de PowerPlus Energy
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
