Powermatic 719T Manual de servicio

Operating Instructions and Parts Manual

Tilting Table Hollow Chisel Mortiser

Model: 719T

Powermatic

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-2474002

Ph.: 800-274-6848 Revision B3 11/2018

Warranty and Service

Powermatic® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or

repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.

Warranty Period

The general warranty lasts for the time period specified in the literature included with your product or on the official

Powermatic branded website.

 Powermatic products carry a limited warranty which varies in duration based upon the product. (See chart

below)

 Accessories carry a limited warranty of one year from the date of receipt.

 Consumable items are defined as expendable parts or accessories expected to become inoperable within a

reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.

Who is Covered

This warranty covers only the initial purchaser of the product from the date of delivery.

What is Covered

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty

does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear,

improper repair, alterations or lack of maintenance. Powermatic woodworking machinery is designed to be used with

Wood. Use of these machines in the processing of metal, plastics, or other materials outside recommended

guidelines may void the warranty. The exceptions are acrylics and other natural items that are made specifically for

wood turning.

Warranty Limitations

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a

Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

How to Get Technical Support

Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof

of initial purchase when calling. If a product requires further inspection, the Technical Service representative will

explain and assist with any additional action needed. Powermatic has Authorized Service Centers located throughout

the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service

Center Locator on the Powermatic website.

More Information

Powermatic is constantly adding new products. For complete, up-to-date product information, check with your local

distributor or visit the Powermatic website.

How State Law Applies

This warranty gives you specific legal rights, subject to applicable state law.

Limitations on This Warranty

POWERMATIC LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH

PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

POWERMATIC SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR

FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF

OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

Powermatic sells through distributors only. The specifications listed in Powermatic printed materials and on the official

Powermatic website are given as general information and are not binding. Powermatic reserves the right to effect at

any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem

necessary for any reason whatsoever.

Product Listing with Warranty Period

90 Days – Parts; Consumable items

1 Year – Motors, Machine Accessories

2 Year – Woodworking Machinery used for industrial or commercial purposes

5 Year – Woodworking Machinery

NOTE: Powermatic is a division of JPW Industries, Inc. References in this document to Powermatic also apply to

JPW Industries, Inc., or any of its successors in interest to the Powermatic brand.

Table of Contents

Warranty and Service .................................................................................................................................... 2

Table of Contents .......................................................................................................................................... 3

Warnings ....................................................................................................................................................... 4

Introduction ................................................................................................................................................... 6

Specifications ................................................................................................................................................ 6

Unpacking ..................................................................................................................................................... 7

Contents of the Mortiser Carton ................................................................................................................ 7

Contents of the Stand Carton .................................................................................................................... 7

Electrical Connections ................................................................................................................................... 8

Grounding Instructions .............................................................................................................................. 8

Converting from 115 to 230 Volt ................................................................................................................ 9

Extension Cords ........................................................................................................................................ 9

Assembly ..................................................................................................................................................... 10

Securing Machine to Stand ..................................................................................................................... 10

Wooden Table ......................................................................................................................................... 10

Operating Handle .................................................................................................................................... 10

Installing Chisel and Bit ........................................................................................................................... 11

Work Stop ................................................................................................................................................ 11

Operating Controls ...................................................................................................................................... 12

Start/Stop Switch ..................................................................................................................................... 12

On-Off Switch Padlock ................................................................................................................................ 12

Adjustments ................................................................................................................................................ 13

90 Chisel to Worktable Calibration ......................................................................................................... 13

Chuck Extension Adaptor ........................................................................................................................ 13

Depth Stop Rod Adjustment .................................................................................................................... 14

Table Position .......................................................................................................................................... 14

Forward/Backward Table Movement ................................................................................................... 14

Lateral Table Movement ...................................................................................................................... 14

Table Tilt Control .................................................................................................................................. 14

Chisel Parallel to Workpiece ................................................................................................................... 15

Operation..................................................................................................................................................... 15

Maintenance ................................................................................................................................................ 16

General .................................................................................................................................................... 16

Sharpening Chisel and Bit ....................................................................................................................... 16

Bit ......................................................................................................................................................... 16

Chisel ................................................................................................................................................... 17

Lubrication ............................................................................................................................................... 17

Storage .................................................................................................................................................... 17

Optional Accessories .................................................................................................................................. 17

Replacement Parts ...................................................................................................................................... 17

719T Mortiser Assembly .......................................................................................................................... 18

719T Mortiser Parts List .......................................................................................................................... 19

719T Mortiser Stand Parts List ................................................................................................................ 22

719T Mortiser Stand Assembly ............................................................................................................... 22

Optional Accessories ............................................................................................................................... 23

Dimensions for 719T with premium chisels mounted ................................................................................. 24

Warnings

1. Read and understand the entire owner’s manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with

all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This mortiser is designed and intended for use by properly trained and experienced personnel only. If

you are not familiar with the proper and safe operation of a mortiser, do not use until proper training

and knowledge have been obtained.

5. Do not use this mortiser for other than its intended use. If used for other purposes, Powermatic

disclaims any real or implied warranty and holds itself harmless from any injury that may result from

that use.

6. Always wear approved safety glasses/face shields while using this mortiser. Everyday eyeglasses

only have impact resistant lenses; they are NOT safety glasses. Also use a dust mask if cutting

operation is dusty.

7. Before operating this mortiser, remove tie, rings, watches and other jewelry, and roll sleeves up past

the elbows. Secure all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips

are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

10. Make certain the switch is in the OFF position before connecting the machine to the power supply.

11. Make certain the machine is properly grounded.

12. Make all machine adjustments or maintenance with the machine unplugged from the power source.

13. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting

wrenches are removed from the machine before turning it on.

14. Keep safety guards in place at all times when the machine is in use. If removed for maintenance

purposes, use extreme caution and replace the guards immediately after maintenance is complete.

15. Make sure the mortiser is firmly secured to the stand before use.

16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged

should be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation. A guard or other part that is damaged should

be properly repaired or replaced.

17. Provide for adequate space surrounding work area and non-glare, overhead lighting.

18. Keep the floor around the machine clean and free of scrap material, oil and grease.

19. Keep visitors a safe distance from the work area. Keep children away.

20. Make your workshop child proof with padlocks, master switches or by removing starter keys.

21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are

careless acts that can result in serious injury.

22. Maintain a balanced stance at all times so that you do not fall or lean against the chisel and drill bits

or other moving parts. Do not overreach or use excessive force to perform any machine operation.

23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for

which it was not designed. The right tool will do the job better and safer.

24. Use recommended accessories; improper accessories may be hazardous.

25. Do not use this tool in damp or wet locations.

26. Maintain tools with care. Keep chisel and drill bits sharp and clean for the best and safest

performance. Follow instructions for lubricating and changing accessories.

27. Make sure the work piece is securely attached or clamped to the table. Do not cut mortises freehand.

28. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do

not use your hands.

29. Do not stand on the machine. Serious injury could occur if the machine tips over.

30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it

comes to a complete stop.

31. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

- - SAVE THESE INSTRUCTIONS - -

WARNING: Drilling, sawing, sanding or machining wood products generates wood dust and other

substances known to the State of California to cause cancer. Avoid inhaling dust generated from wood

products or use a dust mask or other safeguards for personal protection.

Wood products emit chemicals known to the State of California to cause birth defects or other

reproductive harm. For more information go to http://www.p65warnings.ca.gov/wood.

WARNING: This product can expose you to chemicals including lead which is known to the State of

California to cause cancer and birth defects or other reproductive harm. For more information go to

http://www.p65warnings.ca.gov.

Introduction

This manual is provided by Powermatic covering the safe operation and maintenance procedures for a

Powermatic Model 719T Tilting Table Hollow Chisel Mortiser. This manual contains instructions on

installation, safety precautions, general operating procedures, maintenance instructions and parts

breakdown. This machine has been designed and constructed to provide consistent, long-term operation

if used in accordance to instructions set forth in this manual. If there are any questions or comments,

please contact either your local supplier or Powermatic. Powermatic can also be reached at our web site:

www.powermatic.com.

Specifications

Model No. ................................................................................................................................................ 719T

Stock No. ......................................................................................................................................... 1791264K

Stock No – Mortiser only ................................................................................................................. 2474002T

Stock No – Stand only ..................................................................................................................... 6294235T

Motor ........................................................................ TEFC, 1 HP, 1 PH, 115V/230V (Prewired 115V), 60Hz

Spindle speed ................................................................................................................................ 1725 RPM

Table tilt ............................................................................................................................................ 0 to 35

Chisel capacity ..................................................................................................................................1/4" to 1"

Chisel shank diameters ........................................................................................................ 5/8", 3/4", 1-1/8"

Maximum chisel stroke ......................................................................................................................... 10-3/4"

Maximum head stroke .................................................................................................................................. 6"

Maximum chisel center to fence distance .................................................................................................... 4"

Chuck capacity .......................................................................................................................................... 1/2"

Bushing size .......................................................................................................................... 5/8", 3/4", 1-1/8"

Longitudinal table travel ....................................................................................................................... 15-1/2"

Cross table travel ......................................................................................................................................... 4"

Table size ..................................................................................................................................... 7" x 20-1/4"

Fence size .............................................................................................................................. 4-1/2" x 20-1/4"

Base size ........................................................................................................................................... 14" x 16"

Overall dimensions assembled ........................................................................ 21-1/4" L x 21-5/8" W x 74" H

Weight - Mortiser ......................................................................... Net weight 230 lbs., Gross weight 242 lbs.

Weight - Stand ................................................................................. Net weight 46 lbs., Gross weight 50 lbs.

The above specifications were current at the time this manual was published, but because of our policy of

continuous improvement, Powermatic reserves the right to change specifications at any time and without

prior notice, without incurring obligations.

Unpacking

Remove mortiser and stand from the shipping cartons. Report any damage immediately to your distributor

and shipping agent. Do not discard any shipping material until the mortiser is assembled and running

properly.

Compare the contents of your container with the following parts list and Figure 1 to make sure all parts

are intact. Missing parts, if any, should be reported to your distributor. Read this instruction manual

thoroughly to familiarize yourself with the correct assembly and maintenance procedures and proper

safety precautions.

Contents of the Mortiser Carton

1 ea – Mortiser (not shown)

1. 1 ea – Wooden Table

2. 2 ea – M6 x 20 Phillips Head Screws

3. 2 ea – Handwheel Handles

4. 1 ea – Chuck Key

5. 1 ea – Chuck Removal Wrench

6. 1 ea – 23mm Box Wrench

7. 1 ea – Operating Handle

8. 1ea – Chuck Extension Adaptor

9. 2 ea – Chisel Bushings (3/4", 1-1/8")

Note: The Mortiser also comes with a 5/8"

bushing already installed.

10. 1 Work Stop Assembly

Contents of the Stand Carton

1 Stand (not shown)

1 Hardware package – (4) M8 x 45 Hex Cap

Screws, (4) M8 Lock Washers (not shown)

Contents of the Mortiser Carton

Figure 1

Electrical Connections

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and

should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which

have 3-prong grounding type plugs and matching receptacle, which will accept the machine’s plug. Before connecting

the machine to the power line, make sure the switch is in the Off position and be sure that the electric current is of the

same characteristics as indicated on the machine. All line connections should make good contact. Running on low

voltage will damage the machine.

Grounding Instructions

Electrical connections must be made by a qualified electrician in compliance with all

relevant codes. This machine must be properly grounded to help prevent electrical shock and possible fatal

injury.

1. All grounded, cord-connected tools:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to

reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor

and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with

insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If

repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to

a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or

if in doubt as to whether the tool is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding plugs and 3 pole receptacles that accept the tool's plug.

Repair or replace damaged or worn cord immediately.

2. Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating less than

150 volts:

This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A in Figure 1.

The tool has a grounding plug that looks like the plug illustrated in Sketch A in Figure 1. A temporary adapter, which

looks like the adapter illustrated in Sketch B and C, may be used to connect this plug to a 2 pole receptacle as shown

in Sketch C if a properly grounded outlet is not available. The temporary adapter should be used only until a properly

grounded outlet can be installed by a qualified electrician. This adapter is not permitted in Canada. The green-

colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a

properly grounded outlet box.

Figure 2

3. Grounded, cord- connected tools intended for use on a supply circuit having a nominal rating between

150 - 250 volts, inclusive.

This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch D in Figure 1.

The tool has a grounding plug that looks like the plug illustrated in Sketch D in Figure 1. Make sure the tool is

connected to an outlet having the same configuration as the plug. No adapter is available or should be used with this

tool. If the tool must be reconnected for use on a different type of electric circuit, the reconnection should be made by

qualified service personnel; and after reconnection, the tool should comply with all local codes and ordinances.

4. Permanently connected tools:

This tool should be connected to a grounded metal permanent wiring system; or to a system having an equipment-

grounding conductor.

Converting from 115 to 230 Volt

Remove the cover of the push button switch and consult the diagram inside the cover. This diagram is also shown in

Figures 3 and 4. (The diagram inside the cover takes precedence – always check it first ).

Disconnect the machine from the power source.

This mortiser is supplied with four leads that are connected for 115V operation, as shown in Figure 3. Reconnect

these four leads for 230V operation, as shown in Figure 4.

The 115V attachment plug (shown in A, Figure 2) must be replaced with a UL/CSA listed plug suitable for 230V

operation (shown in D, Figure 2). The mortiser must comply with all local and national codes after the 230 volt plug is

installed.

Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly grounded. If

you are not sure, have a registered electrician check the receptacle.

Figure 3 Figure 4

Extension Cords

If an extension cord is necessary, make sure the cord rating is suitable for the amperage listed on the machine’s

motor plate. An undersize cord will cause a drop in line voltage resulting in loss of power and overheating. Use the

chart in Figure 5 as a general guide in choosing the correct size extension cord for the Bandsaw. If in doubt, use the

next heavier gauge. The smaller the gauge number, the heavier the cord.

Recommended Minimum Gauge (AWG) of Extension Cords

Ampere Rating

Volts Total Length of Cord in Feet

115 V 25 ft. 50 ft. 100 ft. 150 ft.

230 V 50 ft. 100 ft. 200 ft. 300 ft.

AWG

< 6 18 16 16 14

6 to 10 18 16 14 12

10 to 12 16 16 14 12

12 to 16 14 12 Not recommended Not recommended

Figure 5

Assembly

Do not connect the machine

to power source until completely

assembled. Read and understand the entire

manual.

Securing Machine to Stand

The mortiser should be secured to the stand

with four M8 x 45 hex cap screws and M8 lock

washers (provided) using the holes in the base.

Make sure there is enough room on each side

of the mortiser for the size stock you plan to

use.

Wooden Table

Referring to Figure 6:

1. Place the wooden table (A) in position on

the slide (B).

2. Secure with two Phillips head screws

provided (C).

Operating Handle

Referring to Figure 7:

1. Fasten operating handle (A) to the hub (B)

and tighten with a 14mm open-end wrench.

2. Raise mortising machine head to the up

position by moving the operating handle

(A) up.

Note: The handle assembly is spring-loaded

and can be repositioned by pulling out the

hub (B) and repositioning it on the pinion

shaft (C).

Figure 6

Figure 7

Otros manuales para 719T

Tabla de contenidos

Otros manuales de Mortajadora de cadena de Powermatic

Powermatic

Powermatic 719T Manual de usuario

Manuales populares de Mortajadora de cadena de otras marcas

Festool

Festool CM 150 Instrucciones de instalación

Scheppach

Scheppach Chisa 7.0 Instrucciones de montaje

Scheppach

Scheppach Chisa 3.0 Instrucciones de montaje

Makita

Makita 7104L Manual de usuario

Mafell

Mafell LS 103 EC Manual de usuario

Record Power

Record Power FM25 Series Guía del usuario

Mafell

Mafell LS 103 EC Guía rápida

Makita

Makita 7104L Manual de usuario

Milwaukee

Milwaukee CM 100 Manual de usuario

Makita

Makita 7104L Manual

Mafell

Mafell LS103Ec Instrucciones de montaje

Mafell

Mafell LS 103 EC Guía rápida

Makita

Makita 7104L Manual de usuario

Makita

Makita 7104L Manual de usuario

Makita

Makita 7104L Manual de usuario

Woodstock

Woodstock SHOP FOX W1671 Manual de usuario

Jet

Jet 719-A Manual de usuario

Makita

Makita 7104L Manual de usuario