Power Craft PBS-950 Manual de usuario
Servotool B.V. • P.O. Box 30159 • 8003 CD Zwolle NL
0512-02
UK Subject to change
UK USERS MANUAL
Art.nr. BSM6006
PBS-950
Belt sander
Powercraft 112Powercraft
Exploded view
2
1
3
5
4
4
13
5
5
4
13
5
5
Fig. C2Fig. C1
78
9
10
6
12
11
13
Fig. B
Fig. A
10 Powercraft
BELT SANDER
The numbers in the following text refer to the drawings on page 2
For your own safety and for the safety of others, please read these instructions
carefully before using this appliance. It will help you understand your product more
easily and avoid unnecessary risks. Keep this instruction manual in a safe place for
future use.
Contents
1. Machine data
2. Safety instructions
3. Operation
4. Maintenance
1. MACHINE DATA
Technical specifications
Productinformation
Fig. A + B
The belt sander is the perfect tool to sand wood and to grind iron, plastic or similar materials.
The belt sander must be used for the rough work, for the normal sanding work an orbital sander
must be used.
1. Rear handle
2. Front handle
3. Front belt roller
4. Clamping lever
5. Direction indicator
6. Cover carbon brush
7. On/off switch
8. Blocking switch
9. Dust collection opening
10. Dust bag
11. Drive belt cover
12. Adjusting knob aligning sanding belt
13. Sanding belt
Voltage | 230 V~
Frequency | 50 Hz
Power input | 950 W
No load sander paper speed | 370m/min
Sanding belt size | 75 x 533 mm
Sanding pad size | 75 x 150 mm
Weight | 3.7 kg
Lpa (Sound pressure) | 94 dB(A)
Lwa (Sound power level) | 170 dB(A)
Vibration value | 2.4 m/s2
Powercraft 3
Spare parts list PBS-950
Powercraft nr. Description Position
409232 Carbon brush (set) 26
409233 Adjusting knob (set) 28 till 30
409234 Rear wheel 35
409235 Bottom plate 48
409236 Belt 49
409237 Switch 61
409238 Dustbag -
UK
UK
Package contents
1 Belt sander
3 Sanding belts
1 Dust collection bag
1 Instruction manual
1 Safety instructions
1 Guarantee card
Check the machine, loose parts and accessories for transport damage.
2. SAFETY INSTRUCTIONS
Explanation of symbols
In this manual and/or on the machine the following symbols are used:
Read instructions carefully
In accordance with essential applicable safety standards of European directives
Class II machine – Double insulation – You don’t need any earthed plug.
Denotes risk of personal injury, loss of life or damage to the tool in case of non-
observance of the instructions in this manual.
Indicates electrical shock hazard.
Wear a dust mask. Working with wood, metals and other materials may produce
dust that is harmful to health. Do not work with material containing asbestos!
Wear eye protection.
Immediately unplug the plug from the mains electricity in the case that the cord gets
damaged and during maintenance
Faulty and/or discarded electrical or electronic apparatus have to be collected at the
appropriate recycling locations.
Electrical safety
When using electric machines always observe the safety regulations applicable in your
country to reduce the risk of fire, electric shock and personal injury. Read the following safety
4Powercraft Powercraft 9
UK
UK
instructions and also the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating plate.
The machine is double insulated in accordance with EN-50144; therefore no earth
wire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The
minimum conductor size is 1.5 mm2. When using a cable reel always unwind the reel
completely.
Special safety precautions
• If you are working with the sanding machine, wear always ear protectors and dust mask.
• The sanding machine is not suitable for wet sanding.
• Check if the switch is not in position “ON”, before you connect the mains plug to the mains
voltage.
• Keep the mains lead always away from moving parts of the tools.
• Use safety glasses, especially when you sand above your head.
• Do not bring pressure to your machine, this will only delay the sanding.
The dust that is produced while working can be detrimental to health, inflammable or
explosive. Suitable safety measures are required. Always wear suitable safety
equipment, for example a dust mask, and use the dust bag.
Immediately switch off the machine when:
• Excessive sparking of the carbon brushes and verticiliosis in the collector.
• Interruption of the mains plug, mains lead or mains lead damage.
• Defect switch
• Smoke or stench of scorched isolation
3.OPERATION
Always observe the safety instructions and applicable regulations.
Choice of the sand-paper
Coarse sand-paper (grain 50) removes in general the bigger part of the material and fine sand-
paper is used for the finishing. If the surface is not even, then start with rough sand-paper.
Further you use middle coarse sand-paper(grain 80) to remove the scratches left behind by the
coarse sand-paper and finally you take fine sand-paper (grain 120) for the finishing.
Environment
In order to prevent the machine from damage during transport, it is delivered in a sturdy
packaging. Most of the packaging materials can be recycled. Take these materials to the
appropriate recycling locations.
Take your unwanted machines to your local Ferm-dealer. Here they will be disposed of in an
environmentally safe way.
Warranty
For the conditions of guarantee, please refer to the separately provided guarantee card.
CE DECLARATION OF CONFORMITY (UK)
We declare under our sole responsibility that this product is in conformity with the following
standards or standardized documents
EN60745-1, EN60745-2-4, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
in accordance with the regulations.
98/37/EEC
73/23/EEC
89/336/EEC
from 01-03-2005
ZWOLLE NL
W. Kamphof
Quality department
It is our policy to continuously improve our products and we therefore reserve the right to
change the product specification without prior notice.
8Powercraft Powercraft 5
UK
UK
the belt sander continuous over the work piece.
• Do not bend the sanding belts
• Do no use the same sanding belt for sanding wood and metal
• Do not bring too much pressure to your machine, this will only delay the sanding.
Troubleshooting
In case the belt sander does not work well, we give you some possible causes and solutions.
1. The electromotor gets hot
• The cool ventilation slots in the motor are stopped up with dirt.
Clean the cool ventilation slots.
• The motor is defect.
Have your belt sander repaired or checked by your local Ferm dealer.
2. The connected machine does not work
• Interruption in the mains connection.
Check mains connection for fracture.
Have your belt sander repaired or checked by your local Ferm dealer.
3. The dust is not absorbed
• This can be caused by a stopped up dust extraction
Clean your dust collection opening
Repairing of electric appliances may be carried out only by experts.
4. MAINTENANCE
Make sure that the machine is not live when carrying out maintenance work on the
motor.
The Ferm machines have been designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends upon proper machine care and
regular cleaning.
Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the motor.
Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt. If the dirt does not come off use a soft cloth moistened
with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please contact your local Ferm dealer.
In the back of this manual you find an exploded view showing the parts that can be ordered.
Powercraft 7
Removing and Installing the sanding belt
Fig. C1 + C2
Before assembly the sanding belt always remove the plug from the mains.
• Put the machine on its side, with the drive belt cover down wards.
• Loosen the sanding belt fastener (4).
• Remove the sanding belt from the machine
• Put a new sanding belt on the machine, make sure that the direction arrows on the sanding
belt are pointing in the same direction as the direction indicator (5).
• Fasten the sanding belt fastener again (4).
Aligning the sanding belt
Fig. B
If the sanding belt doesn’t run parallel with the outer edge of the housing, the sanding belt
must be aligned. Move the sanding belt in the correct position with the adjusting knob (12).
By turning the adjusting knob clockwise the sanding belt will move to the inside and by
turning anti-clockwise the sanding belt will move to the outside.
Switching on and off
Fig. B
• To switch the machine on press the on/off switch (7).
• To switch the machine off release the on/off switch.
If continuous operation is required the blocking switch (8) must be used:
• Switch the machine on to press the on/off switch.
• Press the blocking switch and release the on/off switch.
• To switch the machine off press the on/off switch again and release the on/off switch.
Mounting dustbag
Fig. B
A complete dust bag is enclosed. Put the wire-bracket (inside the dust bag) into to the adapter
of the dust bag (when not mounted). The end of the bracket has to point upwards. Use the dust
bag to collect dust which is released during sanding.
• Put the dust bag on the dust collection opening
• Empty the dust bag regularly in order to obtain an efficient dust extraction.
The adapter of the dust bag can also be used to connect a vacuum cleaner to the machine.
Grip
The use of the belt sander is made easier because of the two grips one on the front side and one
on the back. Through that you can hold the machine with two hands, you have a better control
of the machine and there is less risk to becoming in touch with the moving parts. Hold the belt
sander always with both hands.
Operating instructions
Make sure that the machine has reached its full speed before placing the machine on the work
piece. This will prevent an overload of the machine.
For sanding wood, place the machine approximately 15° out of the grains of the wood. Move
6Powercraft
UK
UK
Otros manuales para PBS-950
1
Tabla de contenidos
Otros manuales de Lijadora de Power Craft
Power Craft
Power Craft 80146 Manual de usuario
Power Craft
Power Craft 62000 Manual de usuario
Power Craft
Power Craft PTS-280 Guía de instalación
Power Craft
Power Craft POS-450 Manual técnico
Power Craft
Power Craft PROS-450 Manual técnico
Power Craft
Power Craft 60219 Manual de usuario
Power Craft
Power Craft PBS-950N Manual técnico
Power Craft
Power Craft 81531 Manual de usuario
Power Craft
Power Craft 55999 Manual de usuario
Power Craft
Power Craft PDS-180N Manual de usuario
