Power Craft 1020W Manual técnico
After Sales Support
Now you have purchased a Power Craft
product you can rest assured in the
knowledge that as well as your 3 year
parts and labour warranty you have
the added peace of mind of dedicated
helplines and web support.
1020W ANGLE GRINDER
User Guide & Warranty
AFTER SALES SUPPORT
UK HELPLINE NO 0905-460005
IRELAND HELPLINE NO 1520-932626
WEB SUPPORT www.heltec.eu
MODEL NUMBER: PAG-125/1020
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
02
Contents
03 Introduction
04 Machine specifications
06 Safety instructions
-General Safety Instructions
-Additional safety instructions
12 Assembly
- Assembling the hand grip
- Assembling and removing the protective cover
- Mounting a grinding disc
- Mounting cutting, grinding discs and roughing
discs
15 Operation
- Deburring
- Cutting
18 Maintenance
22 Exploded view
23 Warranty
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
03
Introduction
Congratulations on choosing to buy a
PowerCraft product.
By doing so you now have the assurance and peace of mind that comes with
purchasing a product made by one of Europe’s leading distributor.
All products brought to you by PowerCraft are manufactured to the highest
standards of performances and safety, and, as part of our philosophy for
customer service and satisfaction, are backed by our comprehensive
3Year Warranty.
We hope you will enjoy using your purchase for many years to come.
1020W ANGLE GRINDER
Always read the instructions for electrical products carefully before
use. It will help you understand your product better and avoid
unnecessary risks. Keep this instructions manual in a safe place for
future use. Include these instructions when giving the appliance to
another user.
The angle grinder is suitable for non-professional use for cutting or deburring
masonry, concrete and metal or separating materials.
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
04
Machine specifications
Technical specifications
Product information
Fig. A
Voltage 230 V~
Frequency 50 Hz
Power input 1020 W
No-load speed 11000/min
Disc diameter 125 mm
Spindle thread size M14
Weight 2.6 kg
Lpa (sound pressure) 94.0 dB (A)
Lwa (sound power) 107.0 dB (A)
Vibration value 8.26 m/s2
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
05
Machine specifications
Fig. A (page 4)
1. On/off switch
2. Guard
3. Grinding disc (not included)
4. Spindle lock
5. Side handle
6. Switch lock
Package contents
1 Angle grinder
1Side handle
1Spanner
1Protective guard
1Carbon brush set
1 Safety goggles
1Instructions manual
1After sales card
1 Quick start guide
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
06
Safety instructions
The following symbols are used in these instructions:
Read the instructions carefully.
Conformity with the relevant EU safety directives.
Class II machine - double insulation - earth connection not
required.
Danger of life and risk of injury as well as risk of damage to the
machine in case of non-adherence to the safety instructions in
these instructions of use.
Danger of electric shock.
Remove the plug from the mains socket.
Keep bystanders away.
Risk of fire.
Wear ear and eye protection.
Wear protective gloves.
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
07
Safety instructions
Faulty and/or discarded electrical or electronic machines have to
be collected at the appropriate recycling locations.
General Safety Instructions
Attention!
When using electric machines always observe the safety regulations
applicable in your country to reduce the risk of fire, electric shock and
personal injury. Read the following safety instructions and also the enclosed
safety instructions. Keep these instructions in a safe place!
For safe working:
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use power tools in damp or
wet locations. Keep work area well lit. Do not use power tools in presence
of flammable liquids or gases.
3. Guard against electric shock.
Prevent body contact with grounded surfaces (e.g. pipes, radiators,
refrigerators).
4. Keep visitors away.
Visitors should be kept away from the work area at all times. Do not let
visitors handle the machine at any time.
5. Storeunused tools.
When not in use keep tools out of reach of children. Store in a dry and
securelocation.
6. Do not force tool.
Do not apply undue pressureas this may affect performance and may
cause damage to the machine. Forcing the job also increases the potential
for accidents.
7. Use right tool.
Do not force small tools or attachments to do the job of heavy duty tool.
Do not use a tool for purposes not intended.
8. Dress properly.
Do not wear loose clothing or Jewellery. They can be caught in moving
parts. Rubber gloves and nonskid footwear are recommended when
working outdoors. Wear protective hair covering to contain long hair.
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
08
Safety instructions
9. Use safety glasses.
Also use face or dust mask when operation is dusty. Use ear protection.
10. Connect dust extraction equipment
If devices areprovided for the connection of dust extraction and
collection facilities ensure these are connected and properly used.
11. Do not abuse cord.
Never carry tool by cord or yank it to disconnect it from electrical socket.
Keep cord from heat, oil and sharp edges.
12. Secure work.
Use clamps or a vice to hold work. It’s safer than using your hand and it
frees both hands to operate tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords
periodically and, if damaged, have repaired by authorized service facility.
Inspect extension cords periodically and replace if damaged. Keep handles
dry, clean and free from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing accessories such as
blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Formthe habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
17. Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch. Be sure switch is off
when plugging in.
18. Outdoor use extension cords.
When tool is used outdoors, use only extension cords intended for use
outdoors and so marked. Always use tool in conjunction with a residual
circuit breaker device.
19. Stay alert.
Watch what you aredoing. Use common sense. Do not operate tool when
you are tired.
20. Check damaged parts.
Check the angle grinder for damaged parts before use. Check for
alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation. Any
part that is damaged should be properly repaired or replaced by our
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
09
Safety instructions
customer service centre unless otherwise indicated elsewhere in this
instructions manual. Have defective switches replaced by our customer
service centre. Do not use tool if the switch does not turn on and off.
21. Warning.
The use of any other accessory or attachment other than recommended in
this operation instructions or the catalogue may present a risk of personal
injury.
22. Have your tool repaired by an expert.
This appliance is manufactured to very high standards and meets relevant
safety regulations. Repairs should only be done by a suitable qualified
electrical engineer or otherwise.
23. Hearing protection should be worn.
24. Never use a power tool with a defective switch.
Any power tool which can no longer be switched on or off is dangerous
and must be repaired.
25. If the connecting line is damaged, it must be replaced by the
manufacturer or by the manufacturer’s customer service representative to
protect people from hazards.
Additional safety instructions
•Check that the maximum speed indicated on the grinding disc corresponds
to the maximum speed of the machine. The speed of the machine must not
exceed the value on the grinding disc.
• Make sure that the dimensions of the grinding disc correspond to the
specifications of the machine.
• Make sure that the grinding disc has been mounted and fastened properly.
Do not use reducing rings or adapters to make the grinding disc fit
properly.
•Treat and store grinding discs in conformance with the supplier’s
instructions.
•Do not use the machine for grinding workpieces with a maximum thickness
exceeding the maximum grinding depth of the grinding disc.
• Do not use grinding discs for deburring.
• When grinding discs have to be mounted on the thread of the spindle,
make sure that the spindle has sufficient thread. Make sure that the spindle
is sufficiently protected and does not touch the grinding surface.
• Before use, inspect the grinding disc for any damage. Do not use grinding
discs which arecrack-ed, ripped or otherwise damaged.
•Beforeuse, let the machine run idle for 30 seconds. Immediately switch off
UK Helpline 0905-460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PAG-125/1020
10
Safety instructions
the machine in case of abnormal vibrations or occurrence of another defect.
Carefully inspect the machine and grinding disc before switching the
machine on again.
• Make sure that sparks do not put people into danger or that they contact
highly flammable substances.
• Make sure that the workpiece is sufficiently supported or clamped. Keep
your hands away from the surface to be cut.
• Always wear safety goggles and hearing protection. If desired or required
also use another kind of protection like for example an apron or helmet.
• Ensure that mounted wheels and points are fitted in accordance with the
manufacturer’s instructions.
• Ensure that blotters are used when they are provided with the bonded
abrasive product and when they are required.
• If a guard is supplied with the tool never use the tool without such a guard.
• For tools intended to be fitted with threaded hole wheel, ensure that the
thread in the wheel is long enough to accept the spindle length.
• Ensure that ventilation openings are kept clear when working in dusty
conditions. If it should become nessesary to clear dust, first disconnect the
tool from the mains supply (use non metallic objects) and avoid damaging
internal parts.
• Use the side handle supplied with the equipment. Any loss of control over
this machine can lead to injuries.
• Though poor conditions of the electrical mains, shortly voltage drops can
appear when starting the equipment. This can influence other equipment
(eq. blinking of a lamp). If the mains-impedance Zmax <0.348 Ohm, such
disturbances are not expected. (In case of need, you may contact your local
supply authority for further information.
• Do not use cutting discs for grinding.
• If a protective cover or guard is supplied with a power tool, never operate
that tool without it.
• Always wear protective gear such as gloves and a dust mask.
Always check that the power supply corresponds to the voltage on
the rating plate.
Your machine is double insulated in accordance with EN 50144;
therefore no earthwire is required.
Tabla de contenidos
Otros manuales de Amoladora de Power Craft
Power Craft
Power Craft S1J-135A Manual de usuario
Power Craft
Power Craft PAG-115/1020 Manual técnico
Power Craft
Power Craft PAG-230/2100 Manual técnico
Power Craft
Power Craft 69162 Manual de usuario
Power Craft
Power Craft AGM6022 PAG-125/1020 Manual de usuario
Power Craft
Power Craft 69780 Manual de usuario
Power Craft
Power Craft PAG-230/2100K Manual de usuario
Power Craft
Power Craft PAG-230/2100K Manual de usuario
Power Craft
Power Craft 11940 Manual de usuario
Power Craft
Power Craft PSM-200 Manual de usuario
