Posligne ODP 200 Manual de usuario
ODP 200
Thermal Receipt Printer
Technical Manual
ODP 200 Technical Manual
2
TABLE OF CONTENTS
1. eneral Specifications
1.1 Printing Specifications
1.2 Character Specifications
1.3 Auto Cutter
1.4 Paper Roll Supply Device
1.5 Paper Specification
1.6 Printa le Area
1.7 Printing and Cutting Positions
1.8 Internal Buffer
1.9 Electrical Characteristics
1.10 EMI and Safety Standards Applied
1.11 Relia ility
1.12 Environmental Conditions
2. Configuration
2.1 Interface
2.1.1 RS-232 serial interface
2.1.2 Specifications
2.1.3 Switching etween on-line and off-line
2.1.4 Interface connector terminal assignments and signal functions
2.1.5 Serial interface connection example
2.1.6 Centronics parallel interface
2.1.7 Data Receiving Timing(Compati ility Mode)
2.1.8 USB Interface
2.1.9 Interface Connector
3. Connectors
3.1 Interface Connectors
3.2 Electrical Characteristics
3.3 Drawer kick-out Connector (Modular Connector)
4. Commands
4.1 Command Notation
4.2 Control Commands
ODP 200 Technical Manual
3
1. eneral Specifications
1.1 Printing Specifications
1) Printing method: Thermal line printing
2) Dot density: 180dpi x 180dpi
203dpi x 180dpi
3) Printing direction: Unidirectional with friction feed
4) Printing width: 72mm(2.83"), 576 dot positions (203dpi)
72.2mm(2.84"), 512 dot positions (180dpi)
80mm(3.15"), 640 dot positions (203dpi)
5) Characters per line(default): Font A: 42
Font B: 56
6) Printing speed: High speed mode:
35.5lines/second maximum
(1/6inch feed) (at 24V, 20℃)
Approximately 150mm/sec maximum
(approximately 5.9inchs/sec maximum)
☞ NOTE: Speeds are switched depending on the applied voltage to the printer and head temperature
conditions automatically.
☞ NOTE: There may e variations in printing after switching the mode of the printing speed. To prevent this
for logo printing with ESC* command, using a downloaded it image is recommended. Change in printing
speed does not occur during down loaded it image printing.
7) Line spacing (default): 1/6 inch (4.23mm)
Programma le y control command.
ODP 200 Technical Manual
4
1.2 Character Specifications
1) Num er of characters: Alphanumeric characters: 95
Extended graphics: 128 × 11 pages
(including one space page)
International characters: 32
① English
② Hangul
③ Chinese (GB2312,Big5)
④ Kanji
2) Character structure: Font A: 12 ℃ 24
Font B: 9 ℃ 17
Hangul, Chinese: 24 ℃ 24
Font A is selected as the default
3) Character size:
EPSON Emulation STAR Emulation
Dot density 0.141℃0.141mm/dot
(180*180dpi)
0.125℃0.141mm/dots
(203*180dpi)
[dpi: dots per 25.4mm{1"}]
3)Printing direction Unidirectional With friction feed
4)Paper width
82.5mm
(3.25")
80mm
(3.15")
60mm
(2.36")
58mm
(2.28")
82.5mm
(3.25")
80mm
(3.15")
60mm
(2.36")
58mm
(2.28")
5)Maximum
printable area
72.2mm
(512dots)
72.2mm
(512dots)
54.1mm
(384dots)
50.8mm
(360 dots)
80mm
(640dots)
72mm
(576 dots)
54.5mm
(436 dots)
52.5mm
(420 dots)
6)Character / line
Font A (12℃24) 42 42 32 30 53 48 36 35
Font B (9℃17) 56 56 42 40 71 64 48 46
Kanji Font (24℃24) 21 21 16 15 26 24 18 17
1.3 Auto Cutter
Partial cut: Cutting with one point center uncut
NOTE: To prevent dot displacement, after cutting, paper must e fed approximately 1mm(14/360 inches) or
more efore printing.
ODP 200 Technical Manual
5
1.4 Paper Roll Supply Device
1) Supply method: Drop-in paper roll
2) Near-end sensor:
a) Detection method: Photo Reflector
) Paper roll spool diameter:
Inside: 12mm(.47″)
Outside: 18mm(.71″)
c) Near-end adjustment: Adjusting LEVER
d) Remaining amount: Fixed position #1 (approximately 20mm(0.78″) #2
(approximately 26mm(1.02″)
NOTE: You can use a command to stop printing upon detection of a paper near-end.
1.5 Paper Specification
1) Paper type: Specified thermal paper
2) Form: Paper roll
3) Paper width:
(82.5mm paper width model)
82 ±0.5mm (3.23" ±0.02")
(80mm paper width model)
79.5 ±0.5mm (3.13" ±0.02")
(60mm paper width model)
59.5 ±0.5mm (2.34" ±0.02")
(58mm paper width model)
57.5 ±0.5mm (2.26" ±0.02")
4) Paper roll size: Roll diameter : Maximum 102mm
Take-up paper roll width:
80 ± 0.5, 1.0mm(3.15"±0.020", 0.04")
5) Paper roll spool diameter: Inside: 12mm(.47")
Outside: 18mm(.71")
NOTE: Paper must not e pasted to the paper roll spool.
ODP 200 Technical Manual
6
1.6 Printable Area
<EPSON Emulation>
6.8mm
0.141mm
<82.5mm { 3.25"} paper width model>
82± 0.5mm
3mm
512 dots
72.2mm(dot # 1- # 512)
4.3mm
<80 mm
{
3.15"
}
paper width model>
0.141mm
79.5± 0.5mm
3mm
512 dots
72.2mm(dot # 1- # 512)
ODP 200 Technical Manual
7
59.5± 0.5mm
<60mm { 2.36"} paper width model>
0.141mm
3mm 2.4mm
384 dots
54.1mm(dot # 1- # 384)
57.5± 0.5mm
0.141mm
3mm 3.7mm
360 dots
<58mm { 2.28"} paper width model>
50.8mm(dot # 1- # 360)
Figure 1.6.1 Printable Area for EPSON Emulation
ODP 200 Technical Manual
8
<STA Emulation default setting>
57.5± 0.5mm
<58mm { 2.28"} paper width model>
0.125mm
2.65mm
420 dots
2.35mm
52.5mm(dot # 1- # 420)
Figure 1.6.2 Printable Area for STAR Emulation (for Default Setting)
4.85mm
0.141mm
79.5± 0.5mm
<80mm { 3.15"} paper width model>
2.65mm
576 dots
72mm(dot # 1- # 576)
0.125mm
ODP 200 Technical Manual
9
59.5± 0.5mm
<60mm { 2.36"} paper width model>
0.125mm
2.65mm 2.35mm
420 dots
54.5mm(dot # 1- # 436)
Figure 1.6.3 Printable Area for STAR Emulation (When the Paper Width Is Changed)
NOTE : The numeric values used here are center values to e used in designing. The printa le area may e out of
alignment y 2 mm maximum to the left or right, due to the paper position or tolerance of parts.
ODP 200 Technical Manual
10
1.7 Printing and Cutting Positions
Center of the print dotline
Auto- cutter blade position
Manual- cutter position
[ Units: mm(Al the numeric values are typical.)]
Appro *12.6
Paper feed direction
Appro * 30.5
Figure 1.7.1 Printing and Cutting Positions
NOTE: Numeric values used here are center values to e used in designing. The values may vary slightly as a
result of paper slack or variations in the paper. Take this into account when setting the cutting position of the auto
cutter.
Appro*21
Appro*11.6
Tabla de contenidos
Otros manuales de Impresora de Posligne
