POS-X ION BLUETOOTH Manual de usuario
Table of Contents
Chapter 1 System Information
1.1 Setup Scanner with PC
1.2 Setup Scanner with Mobile Device
1.3 Configure iOS On-Screen Keyboard
1.4 Memory Mode
1.5 Sleep Settings
1.6 How to Configure the Scanner
Chapter 2 System Setup
2.1 Terminator
2.2 Beeper Tone
2.3 Trigger Mode
2.4 String Options (Prefix & Suffix)
2.5 Setup Insertion
Chapter 3 Barcode Configuration
3.1 UPC-A 17
3 2 UPC-E 20
3 3 EAN-13 23
3.4 EAN-8 25
3.5 Code 39 27
3 6 Codabar 30
3.7 Code 93 34
3 8 Code 128 36
3 9 Interleaved 2 of 5 39
41
43
45
47
49
51
53
55
3.10 Industrial 2 of 5
3.11 Matrix 2 of 5
3.12 China Postage
3.13 MSI/Plessey
3.14 Code 32
3.15 Code 11
3.16 Telepen
3.17 GS1 DataBar
Appendix 61
3
4
4
5
6
7
9
10
11
12
13
Scan Bluetooth SPP Mode
Scan Cradle Pairing Mode
Plug Cradle into Computer
Scan Pairing Mode
Chapter 1 - Scanner Setup
About this manual
This User's Guide provides detailed programming instructions. Barcode
scanners are factory programmed for the most common communication
settings. If you need to change these settings, programming is
accomplished by scanning the barcodes in this guide.
1.1 Setup Scanner PC
To use the scanner with a Windows PC, simply connect the base to your
PC with the provided cable. The scanner is paired with the base by
default. To re-pair the scanner with the base, or to pair the scanner with
a different base, use the instructions below. After scanning each barcode
wait until the scanner beeps before proceeding to the next step.
Wait until the Blue LED on the scanner
and base turn solid
Unplug Cradle from Computer
3
Scan Disconnect Previous Pair
1.2 Setup Scanner with Mobile Device
To use the scanner with a mobile device (iOS, Android, or
Bluetooth Windows device) use the instructions below.
Scan HID Mode
Enable/Disable iOS Quick
Keyboard Shortcut
Toggle iOS
On-Screen Keyboard
To toggle the iOS on screen keyboard a single time, use the
barcode below.
Scan Pairing Mode
Open Bluetooth settings on your mobile device and tap on
"Bluetooth Scanner" to pair with the scanner. The Blue LED on the
back of the scanner will turn solid once it is successfully paired.
1.3 Configure iOS On-Screen Keyboard
When the scanner is connected to an iOS device, rapidly pulling
the trigger twice will toggle the iOS on-screen keyboard. If this
functionality is not needed use the barcode below to disable it.
4
Scan Disconnect Previous Pair
1.4 Memory Mode
The scanner can be configured to store all scanned barcodes in the
scanners internal memory. While in memory mode the scanner will
not transmit any barcodes until the "Transmit Stored Data" barcode
is scanned. The scanner can hold a maximum of X barcodes in
internal memory.
Scanning "Transmit Count of Stored Barcodes" will transmit the
number of barcodes currently held in memory mode. "Clear All
Stored Data" will erase all stored barcodes from the scanners
memory and can not be un-done.
Enter Memory Mode
Transmit Stored Data
Exit Memory Mode
Transmit Count of Stored Barcodes
Clear All Stored Data
5
1.5 Sleep Settings
If the scanner has not been used for a set amount of time the
scanner will automatically enter sleep mode. To take the scanner
out of sleep mode simply press and hold the trigger for 1 second.
To change the amount of time before the scanner enters sleep
mode, scan one of the barcodes below.
WARNING: Longer sleep times may result in shorter battery life
20 Seconds
30 Seconds
1 Minute
2 Minutes
5 Minutes
10 Minutes
20 Minutes
Never
6
1.6 How to configure the scanner
(1) Scan Start Configuration to enter programming mode
(2) Scan all necessary barcodes for settings that meet your needs.
(3) Scan End Configuration to exit programming mode.
Start Configuration End Configuration
Default Settings
Check Version
An asterisk (*) next to an option indicates it is the default setting.
Power Off
7
Most of time the scanner only requires one barcode when changing to
new values. You will hear two beeps when you successfully change a
setting. For some special settings, multiple barcodes are needed to
complete the configuration. When using these special settings, you might
need to read one or more barcodes, such as:
Hexadecimal barcodes. For example: prefix, suffix, etc.
Numeric barcodes. For example: inter-character delay, max/min length
To complete changing the setting you will need to scan the “Confirm”
barcode after scanning from the hexadecimal table. Below is the flow chart
for the two different types of configuration.
8
Chapter 2 - Scanner Configuration
Start Configuration End Configuration
2.1 Terminator
ITEM OPTION
None
*CR+LF
CR
LF
Tab
Output Characters
9
Start Configuration End Configuration
ITEM OPTION
* Ref: Appendix (00-10H)
Beep Tone
(Default : 09H)
* Ref: Appendix (00-10H)
Beep Sound Duration
(Default : 05H)
* Enable
Power On Beeper
Disable
* On
Beeper
Off
2.2 Beeper Tone
10
Otros manuales para ION BLUETOOTH
2
Tabla de contenidos
Otros manuales de Lector de código de barras de POS-X
POS-X
POS-X ION Linear Manual de usuario
POS-X
POS-X Xi3000 Manual de usuario
POS-X
POS-X Xi3000 Manual de usuario
POS-X
POS-X Xi1000 Manual de usuario
POS-X
POS-X ION Short Series Manual de usuario
POS-X
POS-X xi3000 Manual de usuario
POS-X
POS-X EVO Laser Manual de usuario
POS-X
POS-X Xi3000BT Manual de usuario
POS-X
POS-X ION 2D Bluetooth Manual de usuario
POS-X
POS-X ION BLUETOOTH Manual de usuario
