Portfolio WL126WW Manual de usuario

ITEM #0398473

0398474

MODEL #WL126WW

WL126BK

WALL LANTERN

Français p. 11

Español p. 21

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday,

8 a.m. - 5 p.m., EST, Friday.

Portfolio® is a registered trademark

Lowes.com/

ortfolio

EB1596

For Wet

Location

PACKAGE CONTENTS

HARDWARE CONTENTS (shown actual size)

Wire

Connector

Qty. 3

Decorative

Screw

Qty. 2

Lowes.com/

ortfolio

H Housing Screw 1

(preassembled to Housing Cover (E))

A Fixture 1

C Housing 1

B Mounting Plate 1

PART DESCRIPTION QUANTITY

D Panel 4

E Housing Cover 1

F Cap 1

G Bottom Finial 1

CC DD

Top Finial

Qty. 1

Top Finial

Screw

(preassembled

to Top Finial

(CC))

Qty. 1

READ AND SAVE THESE INSTRUCTIONS.

DANGER

• For your protection and safety, carefully read and understand the information provided in this manual

completely before attempting to assemble, install or operate this product. Failure to do so could lead

to electrical shock, fire or other injuries that could be hazardous or even fatal.

• If using this light fixture in a WET or DAMP location, this light fixture must be connected to a supply

circuit that is protected by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal

injury, electrical shock or death.

• DO NOT connect this fixture to an electrical system that does not provide a means for equipment

grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an

electrical system not having a proper grounding means could cause metal parts of the fixture to carry

electrical currents if any of the fixture wires, wire connections or splices were to become broken, cut

or loose during the mounting or normal operation of the fixture. Under this condition, anyone coming

in contact with the fixture would be subject to electrical shock, which could cause serious injury or

death.

• DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying

wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture ground wire to the

black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this

condition, anyone coming in contact with the fixture will receive electrical shock, which could cause

serious injury or death.

• DO NOT damage or cut the wire insulation (covering) during installation of fixture. DO NOT permit

wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation,

which could cause serious injury or death from electrical shock.

WARNING

• All electrical connections must be in agreement with local codes and ordinances, the National

Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn

about your local codes, permits and/or inspections.

• To avoid personal injury, the use of gloves may be necessary while handling fixture parts with sharp

edges.

• DO NOT suspend any fixture by the house wires.A fixture must always be mounted directly to a

mounting plate that is first attached to the outlet box. All fixtures must be mounted to an outlet box that

is supported by the building structure. Wire connectors will not support the weight of a fixture.

Suspending a fixture by the house wires and wire connectors will result in the fixture falling, with the

possibility of personal injury and the danger of electrical shock or fire.

• To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light

fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture.

If your house wire is larger than 12-gauge or there is more than one house wire to connect to the

corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.

• To avoid water damage to fixture or possible electrical malfunction, install fixture at least 4 ft. above

the ground/floor.

• Failure to caulk fixture mounting surface with silicone weather sealant may result in water damage

in outlet box, which may cause electrical malfunction or electrical shock.

SAFETY INFORMATION

Lowes.com/

ortfolio

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents. If any part is missing or damaged, do not attempt to assemble

the product.

Estimated Assembly Time: 40 minutes

Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Wire

Strippers, Pliers, Wire Cutters, Safety Glasses, Stepladder, Electrical Tape, Silicone Weather Sealant

Helpful Tools (not included): A/C Tester Light, Do-It-Yourself Guide, Soft Cloth, Level

ASSEMBLY INSTRUCTIONS

OFF

Turn off circuit breakers and wall switch to

the fixture supply line leads.

DANGER: Failure to disconnect power

supply prior to installation may result in

serious injury or death.

PREPARATION

CAUTION

• TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by

removing the fuse (or switching the circuit breaker off).

• If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture.

Contact a qualified, licensed electrician for information regarding the proper grounding methods as

required by the local electrical code in your area.

• DO NOT use bulbs having a wattage greater than the maximum value stated on the fixture. The use

of bulbs with higher wattage than specified will increase temperatures and risk of fire.

•If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct

type to use as well as the electrical rating required.

• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F. Consult a qualified

electrician before installation.

SAFETY INFORMATION

Lowes.com/

ortfolio

ASSEMBLY INSTRUCTIONS

Remove existing fixture and disconnect all

electrical wiring.

Lowes.com/

ortfolio

Feed wires from outlet box (not included)

through center of mounting plate (B). Attach

mounting plate (B) to outlet box using the

existing outlet box screws and washers. Use a

level (not included) to adjust mounting plate (B)

so fixture screws are parallel with floor and

ceiling. Tighten outlet box screws to secure

mounting plate (B).

Make sure the outlet box can support 35 lbs.

hanging weight. Use metal outlet box; plastic

outlet boxes are not recommended.

4. Attach bottom finial (G) to bottom of fixture (A).

Align small gap in opening at bottom of housing

and press down very firmly. Make sure housing

Outlet Box

Screws and

Washers

Small Tab

Lowes.com/

ortfolio

ASSEMBLY INSTRUCTIONS

Connect WHITE wire from fixture (A) to WHITE wire

from outlet box using existing wire connector or wire

connector (AA). Connect BLACK wire from fixture (A)

to BLACK wire from outlet box using existing wire

connector or wire connector (AA). Connect

BARE/GREEN ground wire from outlet box to BARE

wire from fixture (A) using existing wire connector or

wire connector (AA).

NOTE: Screw wire connectors (AA) on in a clockwise

direction.

WARNING: Never connect ground wire to white

or black power supply wires.

WARNING: To reduce the risk of fire, electrical

shock or personal injury, wire connectors provided

with this light fixture are designed to accept only one

12-gauge house wire and two lead wires from the

light fixture. If your house wire is larger than

12-gauge or there is more than one house wire to

connect to the corresponding fixture lead wires,

consult an electrician for the proper size wire

connectors to use.

x 3

Insert panels (D), beveled side out, into each slot

on inside of housing (C).

Tip: When inserting last panel (D), slide the panel

(D) down as far as possible on one side. Then,

while pressing in with your fingers at the bottom of

the panel (D), bring the top of the panel (D) in

toward the corner until the panel (D) slips into

place. This may require quite a bit of pressure but

be careful not to press so hard that you break

one or more panels (D).

Unwrap BARE wire from BLACK and WHITE wires

on fixture (A). Prepare wire by stripping 3/4 inch of

insulation from wire ends using wire strippers (not

included).

6a.

6b.

Hardware Used

Wire Connector

Outlet

Box

BARE/

GREEN

WHITE

BLACK

AA AA

BARE

ASSEMBLY INSTRUCTIONS

Lowes.com/

ortfolio

Align holes in fixture (A) with corresponding screw

holes in mounting plate (B).

Secure fixture (A) to mounting plate (B) with

decorative screws (BB).

Wrap electrical tape (not included) around each

individual wire connector (AA) down to the wire.

WARNING: Make sure no bare wire or wire

strands are visible after making connections.

Carefully arrange excess wiring and wire

connectors (AA) within outlet box.

9. 9

x 2

Hardware Used

Decorative Screw

Install one standard-base bulb (not

included). Use either a 60-watt max.

incandescent or a 13-watt CFL.

IMPORTANT: When replacing bulb, please

allow bulb and fixture (A) to cool down

before touching them.

Outlet

Box

Bulb

ASSEMBLY INSTRUCTIONS

Lowes.com/

ortfolio

Position housing cover (E) onto housing (C),

making sure to align notches and small

triangles on housing cover (E) with top edge

of housing (C) before positioning slots with

larger triangles.

Lower housing cover (E) so that housing

screw (H) fits in keyhole slot in top edge of

housing (C).

10. 10

Remove top finial screw (DD) from top finial (CC).

Locate hole at top of housing cover (E) and insert

top finial screw (DD) through hole from underside

of housing cover (E).

Align hole in cap (F) with top finial screw (DD).

Secure with top finial (CC).

NOTE: Make sure to align cap (F) with housing

cover (E) after tightening top finial (CC).

11.

x 1

Hardware Used

Top Finial

x 1

Top Finial Screw

Notches

Slots

Keyhole Edge

ASSEMBLY INSTRUCTIONS

13. After completing installation, caulk fixture

(A) mounting surface with silicone weather

sealant (not included).

WARNING: Failure to caulk fixture

mounting surface with silicone weather

sealant may result in water damage in

outlet box, which may cause electrical

malfunction or electrical shock.

Lowes.com/

ortfolio

Restore power and test fixture (A).

If light does not function, please refer to

TROUBLESHOOTING on the next page.

12. 6

Portfolio® is a registered trademark

Printed in China

Lowes.com/

ortfolio

CARE AND MAINTENANCE

The distributor warrants all of its lighting fixtures against defects in materials and workmanship for

five (5) years from the date of purchase. If within this period the product is found to be defective, take

a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of

purchase. The distributor will, at its option, repair, replace or refund the purchase price to the

consumer. All costs of installation and removal of the fixture is the responsibility of the consumer. This

warranty does not cover fixtures becoming defective due to misuse, accidental damage or improper

handling and/or installation and specifically excludes liability for direct, incidental or consequential

damages, improper packaging of returned products and acts of God. As some states do not allow

exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply.

This warranty gives you specific rights and you may also have other rights which may vary from state

to state.

WARRANTY

TROUBLESHOOTING

WARNING: Before beginning work, shut off the power supply to avoid electrical shock.

Bulb will not light.

Fuse blows out or

circuit breaker trips.

1. Bulb is burned out.

2. Power is OFF.

3. Faulty connection.

1. Crossed wires.

2. Power wire is grounding out. 1. Check wiring.

2. Check all connections.

1. Replace bulb.

2. Make sure power supply is ON.

3. Check wiring and all connections.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

•Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean

panels. Do not use an abrasive cleaner on panels or fixture.

PWLI1502

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Luz exterior de Portfolio

Portfolio

Portfolio DL6906RBS Instrucciones de instalación

Portfolio

Portfolio SS39P-P3-BK-C1 Manual de usuario

Portfolio

Portfolio P1015B Manual de usuario

Portfolio

Portfolio RS60M-F10-BK-C Manual de usuario

Portfolio

Portfolio 18224 Manual de usuario

Portfolio

Portfolio E3A Manual de usuario

Portfolio

Portfolio B10065 Manual de usuario

Portfolio

Portfolio 34253 Manual de usuario

Portfolio

Portfolio PL127MBK Manual de usuario

Portfolio

Portfolio LBSHC01MT Manual de usuario

Portfolio

Portfolio 16073 Manual de usuario

Portfolio

Portfolio 00768 Manual de usuario

Portfolio

Portfolio FY09-010 Manual de usuario

Portfolio

Portfolio 16025 Manual de usuario

Portfolio

Portfolio LBSHC007 Manual de usuario

Portfolio

Portfolio 00686 Manual de usuario

Portfolio

Portfolio 00751 Manual de usuario

Portfolio

Portfolio SL26Cb-R5-ORB-2 Manual de usuario

Portfolio

Portfolio Q91EL1001-08 Manual de usuario

Portfolio

Portfolio 00744 Manual de usuario

Portfolio

Portfolio 00605 Manual de usuario

Portfolio

Portfolio RD11C-R5-SV-2 Manual de usuario

Portfolio

Portfolio RD13M-M25-BK-4 Manual de usuario

Portfolio

Portfolio 0688491 Manual de usuario

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

BEGA

BEGA 84 253 Manual

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario