PolyJohn Comfort XLT PH04 Manual de usuario
PH04 Comfort XLT Grab Bar - June 2019
Page 1 of 3
PH04 Comfort XLT™
Grab Bar
Mounting Instructions
POLYJOHN
USA
PolyJohn Enterprises Corp
2500 Gaspar Ave.
Whiting, IN 46394
Phone: 800-292-1305
Fax: 219-659-0625
www.polyjohn.com
POLYJOHN
WORLDWIDE
PolyJohn (UK) Ltd.
Equinox 1 Audby Lane
Wetherby, England LS22 7RD
Phone: 44 (0) 1937-583333
Fax: 44 (0) 1937-583322
POLYJOHN
CANADA
PolyJohn Canada
P.O. Box 2300
199 Forest Plain Rd.
Orillia, Ontario LV3 6S2
Phone: 800-465-9590
Fax: 705-325-8250
Thank you for purchasing the optional grab bar kit for the
Comfort XLT unit. The 2019 redesign of the Comfort XL
unit to incorporate a larger tank with ushing capabilites
does not require internal grab bars. Please read through
these instructions prior to installing the grab bars. If your
unit has the optional urinal installed, the left side grab bar
will not be used. If your unit has the optional sink (required
for the fresh ush option), you will be installing the shorter
PH04-0020 grab bars on the rear and right side wall.
All references to left and right will be from viewing the
unit from the front.
GENERAL OVERVIEW
~~Tools Required for Assembly~~
• 13/64” Drill Bit • Rivet Gun w/ 3/16” nose piece • Tape Measure
PH04 Comfort XLT Grab Bar - June 2019
Page 2 of 3
PC-000106 Washer
PC-000105 Rivet
To mark the holes to mount the left side grab
bar (if no urinal is installed), use the diagram
to the right as a reference, and mark the
mounting hole locations as shown. There are
a total of 8 hole locations for each grab bar.
Five (5) of the holes are located at a height of
32-1/4” from the top of the base surround, and
three (3) holes at a height of 30-1/4” . The
hole locations on the corner panels are lo-
cated halfway between the center rib and the
corner/side connection.
For units without a sink installed: Repeat
this for the rear and left panel grab bars.
For units with a sink: For the rear panel, make
marks in the same locations, eliminating the
3 locations in the right rear (when viewing
the unit from the front). For the left side pan-
el, make marks in the same locations, eliminating
the 3 spots in the right rear
Using a drill with a 13/64” drill bit, drill holes in the locations just marked.
Step 1. Grab Bar Mounting Locations
32-1/4”
30-1/4”
ASSEMBLY INSTRUCTIONS
Step 2. Grab Bar Installation
On the inside of the right side panel, mea-
sure and position the bottom of the grab
bar at 26” up from the top of the base sur-
round. If installing the grab bars with the
sink, simply insert the straight end of the
grab bar into the corresponding slot of teh
sink surround and level the grab bar. With
one person holding the grab bar in place
on the inside of the unit, have another per-
son drill
13/64” diameter holes through the holes
drilled in the previous step.
Be sure to drill through only one wall of the
grab bar.
Place PC-000106 Back-Up Washers on
PC-000105 rivets, and rivet the grab bar in
place. Repeat this step for the rear and
left panel grab bars.
26”
PH04 Comfort XLT Grab Bar - June 2019
Page 3 of 3
We highly recommend membership in the Portable Sanitation Association International (PSAI); the world-
wide authority on portable sanitation services. The PSAI, “Portable Sanitation Industry Certication Program”
manual contains a wealth of information of standards and service procedures. For more information contact
the PSAI:
PORTABLE SANITATION ASSOCIATION INTERNATIONAL
7800 METRO PARKWAY, SUITE 104
BLOOMINGTON, MINNESOTA 55425 USA
800-822-3020 / 612-854-8300 (FAX: 612-854-7560)
www.psai.org
PolyJohn Enterprises Corporation publishes a series of technical manuals of guides for the Portable Sanita-
tion Association International. Contact your area sales representative for further details.
For a source of cleaning, deodorizing, and paper products contact:
POLYJOHN
2500 GASPAR AVE.
WHITING, IN 46394-2175
800-292-1305
“PolyJohn is a family owned, state of the art, plastics manufacturing company dedicated to providing its
employees with a work environment committed to excellence, and its customers with innovative products,
services and technology that meet or exceed their requirements.”
OUR MISSION STATEMENT
Look for us on the Web @ www.PolyJohn.com
THANK YOU FOR PURCHASING POLYJOHN PRODUCTS!
• Use a mild soap to clean all surfaces and component parts.
• Minor scratches and abrasions can be lightly sanded or scrubbed with a mild abrasive cleaner (such as
“Soft Scrub”) that contains calcium carbonate, hypochlorate bleach, and detergents. Be sure to follow the
cleaning product directions since these ingredients may cause hazardous gases when mixed with other
chemicals. Rinse the cleaned areas and buff with a conventional wax.
• Some light scratches may also be hidden by using an industrial hot air gun.
CLEANING AND MAINTENANCE
• To keep the interior smelling fresh, spray with a deodorant spray.
Otros manuales para Comfort XLT PH04
1
Otros manuales de Baño de PolyJohn
PolyJohn
PolyJohn Comfort XLT FLUSH Series Hoja de instrucciones
PolyJohn
PolyJohn Comfort XLT Series Hoja de instrucciones
PolyJohn
PolyJohn FLEET Series Hoja de instrucciones
PolyJohn
PolyJohn Comfort Inn PH03 Manual de usuario
PolyJohn
PolyJohn PH04 COMFORT XLT Series Hoja de instrucciones
PolyJohn
PolyJohn PJP4 Series Hoja de instrucciones
PolyJohn
PolyJohn PJN3 Series Hoja de instrucciones
PolyJohn
PolyJohn PolyLift PL01-1000 Manual de usuario
PolyJohn
PolyJohn Comfort XLT PH04 Manual de lista de piezas
PolyJohn
PolyJohn MINI-FLUSH MF02-1000 Hoja de instrucciones
Manuales populares de Baño de otras marcas
Better Bathrooms
Better Bathrooms BUN/BeBa 27555/78725 Manual de usuario
American Standard
American Standard CONCEPT Cube TF-2704 Manual de usuario
BIOLAN
BIOLAN ECO Manual de lista de piezas
Thetford
Thetford C260 Series Manual de usuario
KELISS
KELISS T162A Series Manual de usuario
Kohler
Kohler K-22241K Instrucciones de montaje
