point KS49WN Manual de usuario
User Manual
UPRIGHT FRIDGE
KS49WN/KS49XN
Thank you for purchasing your new POINT Upright Fridge. These
operating instructions will help you use it properly and safely. We
recommend that you spend some time reading this instruction manual
in order that you fully understand all the operational features it oers.
Read all the safety instructions carefully before use and keep this
instruction manual for future reference.
Takk for at du kjøpte ditt nye POINT stående kjøleskap. Denne
bruksanvisningen vil hjelpe deg med å bruke den på en trygg og riktig
måte. Vi anbefaler at du tar deg tid til å lese gjennom hele
bruksanvisningen for å bli fortrolig med alle funksjonene som tilbys.
Les alle sikkerhetsanvisningene nøye før bruk, og oppbevar
bruksanvisningen for fremtidig referanse.
Kiitos, kun valitsit uuden POINT-jääkaappi. Nämä käyttöohjeet
opastavat sinua käyttämään laitetta oikein ja turvallisesti. On
suositeltavaa käyttää aikaa tämän käyttöoppaan lukemiseen, jotta
ymmärrät täysin, mitä toiminnallisia ominaisuuksia tuote tarjoaa. Lue
kaikki turvallisuusohjeet huolellisesti ennen laitteen käyttöä ja säilytä
käyttöopas myöhempää käyttöä varten.
Tak for købet af dit nye køleskab fra POINT. Disse brugervejledninger
hjælper dig med at bruge dette apparat rigtigt og sikkert. Vi anbefaler,
at du læser denne brugervejledning, så du får en fuld forståelse af
hvordan alle funktionerne virker. Læs sikkerhedsforskrifterne grundigt
inden brug, og gem denne brugervejledning til senere brug.
Tack för att du har köpt ditt nya stående kylskåp från POINT. Denna
bruksanvisning hjälper dig att använda den på ett säkert och korrekt
sätt. Vi rekommenderar att du tar dig tid att läsa igenom denna
bruksanvisning för att till fullo förstå alla driftfunktioner som den
erbjuder. Läs noga igenom alla säkerhetsinstruktioner före användning
och spara bruksanvisningen för framtida bruk.
4 - 22
23 - 41
42 - 60
61 - 79
80 - 98
3
54
1. WARNING Keep ventilation openings, in the
appliance enclosure or in the built-in structure, clear
of obstruction.
2. WARNING Do not use mechanical devices or other
means to accelerate the defrosting process, other
than those recommended by the manufacturer.
3. WARNING Do not damage the refrigerant circuit.
4. WARNING Do not use electrical appliances inside the
food storage compartments of the appliance, unless
they are of the type recommended by the
manufacturer.
5. The appliance has to be unplugged after use and
before carrying out user maintenance on the
appliance.
6. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
7. Children should be supervised to ensure that they do
not play with the appliance.
8. If the mains power cable is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
Warning
9. Please abandon the refrigerator-freezer according to
local regulations because it uses flammable blowing
gas and refrigerant.
10. Disconnect the mains power supply before replacing
the lamp.
11. Follow local regulations regarding the disposal of the
appliance because of its flammable refrigerant and
blowing gas. Before you scrap the appliance, take o
the doors to prevent children being trapped inside.
76
(Built-in)
Display control panel
Tray on
the door
Tray on
the door
Tray on
the door
Tray on
the door
Tray on
the door
Glass shelf
Glass shelf
Big fruit
and
vegetable
box
Some of the features and accessories of the refrigerator you bought might
not match with the illustrations; always refer to the packing list in the
refrigerator.
Names of the components
(Built-in)
Except the solutions recommended by the manufacturer, do not use
mechanical equipment or other means to accelerate defrosting.
Except the types recommended by the manufacturer, do not use any
electrical appliance inside the food closet.
The refrigerator is provided with R600a refrigerant and cyclopentane
foaming material and both are combustible materials. Obsolete
refrigerator should be isolated from fire and combustion treatment is
forbidden.
Preparation before using
Warning
Remove all packing materials before using, including the bottom seating
washer, the foam pads and the gummed paper inside.
Use a warm and wet cleaning cloth to wipe the refrigerator's interior and
exterior (add a little detergent in the warm water and use clean water to
clean up).
Prepare a separating grounding receptacle with both polarities. Do not
share multi- purpose socket with other electrical appliances.
Connect earth wire. Earth electrode of the socket must be equipped with
a reliable grounding wire.
New refrigerator
98
Place the refrigerator in a well ventilated place, far away from any heat
sources and direct sunlight. In order to avoid rust or reduce insulation
result, do not place it in a damp place.
Space above the refrigerator shall not be less than 30cm. The distance
against the two sides shall not be less than 10cm. Distance from the wall
shall not exceed 75mm, providing convenience to open and close the door
and disperse the heat.
Place the refrigerator on a flat and solid floor. (if it is not stable, you can
level the refrigerator with the regulating legs)
Placement
Attention
Make sure the mains power cable is not pressed by the refrigerator or
other articles. Before connecting to the mains power supply, make sure
the voltage range of the refrigerator follows with that of the mains
power supply.
Correct application of the refrigerator
Ensure that the refrigerator is placed correctly and stably. Be aware of all
safety matters that needing attention.
1. Connect the electricity
After connecting the electricity, it will enter into ex-factory state.
2. Put food into the refrigerator
Suggestion: after some time, the refrigerator will reach food storage
temperature or after the first stop of the compressor, put food into it, which
is beneficial to retain food freshness.
Note: if the set temperature is altered or new food is put in, the temperature
inside the box will balance after a time, which is determined by the
temperature alteration degree, temperature of ambient environment,
opening frequency, quantity of the food inside and so on.
Do not invert, traverse, press or shake the refrigerator. When moving the
refrigerator, the angle of inclination shall not be larger than 45°.
When moving, do not make excessive pressure to the door or top cover,
otherwise deformation will occur.
Slightly angle the refrigerator backwards (less than 20°) to move a short
distance.
Transportation and placement of the refrigerator
Transportation
2 31
A
B
C
D
1. Keys
Hi Humidity: High Humidity Mode
ON/OFF: start up or shut down the system
Increase temperature of the cooling chamber
Decrease temperature of the cooling chamber
2. Names of functions of display screen
High Humidity figure
Temperature region digitron
Temperature (°C) icon
Under normal operation, it will not illuminate any more after thirty
seconds without opening and key operation.
When the door is open, the display will illuminate all the time and it will
stop illuminating thirty seconds after the door is closed.
When a failure happens and it is within "Failure Code", the display will
illuminate for one time and stop to illuminate after thirty seconds (if the
buzzer has been ringing for a long time, press any key to cancel the failure
bell).
Display control:
3. Display control
Power on for the first time: all illuminate for three seconds with ringing of
start bell. Defaulting temperature of the cooling chamber is 5°C.
Normal operation display:
Temperature display region: when there is a failure, it will show failure codes
in turn at a priority order; without failure, it will show the set temperature.
High Humidity figure: shine when the system is under High Humidity Mode.
Function introduction
1110
4. User Mode operation
Start-up and shutdown
Under start-up mode, press and hold ON/OFF key (B key) for three seconds,
the start bell will ring and the system will shut down immediately;
Under shut down mode, press and hold ON/OFF key (B key) for three
seconds, the start bell will ring and the system will start immediately.
Press ON/OFF key for three seconds to shut down the system and the display
will not illuminate any more. Except ON/OFF key (B key), other keys will stop
responding, and compressor, door lamp and other loads will be shut down
immediately;
Press ON/OFF key for three seconds to start up the system. Before starting,
if the system is at High Humidity Mode, the High Humidity figure will
illuminate, otherwise the system will only illuminate the set temperature and
will run the mode having been set before shutdown.
The following functions must be worked under the start state.
High Humidity Mode
When the system is not at High Humidity Mode, press and hold Hi Humidity
key (A key) for three seconds to start the High Humidity Mode and High
Humidity figure will illuminate.
When the system is at High Humidity Mode, press and hold Hi Humidity key
(A key) for three seconds to exit from the High Humidity Mode and High
Humidity figure will not illuminate any more.
When starting High Humidity Mode, the cooling chamber will work under
High Humidity mode to improve the relative humidity of the air inside the
cooling chamber.
Set the temperature of the cooling chamber
Press temperature regulation keys ∧ (C key) and ∨ (D key) to set the
temperature inside the chamber and the set temperature will illuminate. The
setting range is between 2°C to 8°C (non-periodic temperature regulation); it
(within five seconds after finishing the setting, press A key or B key to
confirm the setting state manually and make the setting valid.)
5. Illuminating lamp control
When the door is open, the cooling chamber's lamp will illuminate. When the
door is closed, the cooling chamber's lamp will not illuminate any more.
6. Door-opening hint and door-opening alarming control
If the door has been open for 120 seconds, it will ring warning bell, and the
bell will ring every 2 seconds until the door is closed. Press any key to cancel
the door-opening warning.
7. Power-interruption memory and initial power-up state
When there is a power interruption, the refrigerator can automatically
memorise the operating mode and state before the power interruption;
When the power returns, it will return to the state before the interruption
and run the mode having been set before interruption.
Initial power-up state: the set temperature of cooling chamber is 5°C and
the system is not at High Humidity Mode.
Memory: include set temperature of cooling chamber, "High Humidity"
Mode and cumulative working hours of compressor.
For example, if the system has a power failure under High Humidity state,
it will continue to work at "High Humidity" mode after recovery.
8. High temperature warning of the cooling chamber
When the temperature of the cooling chamber has been above 15°C for six
hours, the high temperature warning will ring. The buzzer will ring every
second for ten times and then ten times every thirty minutes, and
temperature display region will show failure code (E9); the ringing will stop
when the temperature of the cooling chamber is below 10°C. Press any key to
cancel the warning buzzer (if it does not buzz after thirty minutes). But the
failure code display state is not canceled, until the failure is solved.
1312
9. Failure hint
Failure code
E1
E4
E7
E6
E9
EC
Failure codeHint
Cooling sensor failure
Hint
Communication failure
Cooling defrosting sensor
failure
High temperature warning
of the cooling chamber
Ambient temperature
sensor failure EEPROM circuit failure
Note: when there is a failure, the system will display all failures' codes i n
turn.
The warning will be automatically canceled after recovery of the failure or
press any key to cancel the warning. When failure happens, it is a priority to
show failure code till failure recovery, otherwise the set temperature and
High Humidity state cannot be displayed. If a failure has been displayed all
the time and automatic recovery fails, contact After-sale Department or
professional maintenance personnel.
Refrigerator maintenance
In order to avoid accidental
harm caused by closing a
child inside or refrigerator
falling, do not allow the
children to enter into or climb
the refrigerator.
Do not put heavy
things on the
refrigerator,
otherwise it will easily
fall and cause harm.
Do not put too
much food into the
refrigerator.
Do not open the door and drawers
for a long time or frequently open
the door and drawers, otherwise it
would weaken the eciency of the
complete machine and increase
operating load.
When the refrigerator is not
operating normally, turn o
the mains power supply and
inform local service center.
Do not splash water on the top
or back of the refrigerator,
otherwise it would reduce
insulation eect.
Attention:
The product is a household refrigerator. According to the national standards,
household refrigerator is only applicable to store food and cannot be used for
other purpose such as storing blood, drugs, biological products, etc.
Do not arbitrarily dismantle or
repair. Choose the repair
shops designated by the
manufacturer to replace the
accessories.
In order to
avoid fire, do
not use
combustible
solvents
nearby the
refrigerator.
Use standard professional
three-hole power socket
(above 10A). Socket
grounding must be good.
In order to avoid, fire and other accidents,
do not put anything combustible, explosive,
volatile and strongly corrosive into the
refrigerator. In order to avoid freezing,
rupture and other losses, do not put the
bottles with fluids or sealing containers into
the refrigerating box.
Pesticide
Cosmeti cs
Amyl
accetate
Binde r
Alcohol
1514
Cleaning
Alkaline or alkalescent detergents; (may cause the inner liner and plastic
components to crack)
Soap powder, benzine, amyl acetate, alcohol, etc.; (may destroy the
plastic components)
If cooking oil or seasonings blot on the refrigerator's external surface,
clean it immediately. (may cause the plastic components to crack)
Do not use the following products to clean refrigerator interior:
Unplug the mains power to avoid an electric shock or
fire due to mains power cable aging; clean up
refrigerator interior; open the door for a time and
close it after the interior become completely dry.
Non-use within a
long time
Reduce opening times as many as possible; and do
not put fresh food in.
Power failure
When discarding unused refrigerator, door seal must
be dismantled o, so that children cannot be closed
inside by accident.
Discard
Fingerprints are easily left on exterior. Use a dry towel to wipe away.
Periodically clean away the dust left at the back of and under the
refrigerator.
Refrigerator interior should be cleaned frequently so as to avoid
foreign odor. After the mains power is turned o, use a soft towel and
neutral detergent to clean and wipe with the clean water.
Lamps and replacement
Halt
If the lamp fails to illuminate, contact professional personnel for home
service.
Door Right-Left Change
Remove the two nut caps and two hinge cover plates from the top beam
(open the door toward right).
Remove decorating components from the top beam.
Remove the two bolts fixed with hinges, pull the hinges out from one side
and dismantle the door at the same time. As last, take the hinges out
from the door.
Left cover plate Nut cap Right cover plate
Top-beam
decoration
Top-beam
decoration
Two bolts Hinge
Top-beam
decoration
Wiring bundles
1716
Reassemble the lower hinge axis: dismantle the original hinge axis and
assemble it at the graphic position.
Reassemble the upper hinges axis: dismantle the hinge axis and assemble
by rotating it from the other end of the screw hole.
Install the upper hinges fixed leg (on the left) at the right side.
Install the lower hinge at the right side of the refrigerator.
Install the upper hinges into the relative axle holes on the right (upon the
door) at first, then place the door on the lower hinges, press upper hinges
into hinge fixed legs and fix the upper hinges at last.
Install top-beam decoration, nut caps and hinge cover plates.
Lower hinge
1918
Connecting guide for refrigerator and freezer cabinets
Step 1: Put two cabinets together with
only 10mm gap. Fix the connecting hinge
to the place as shown in the picture.
Step 3: Put the bar inside the gap between two cabinets. The connecting Step
finished.
Step 2: Fit the lower connecting hinge at
the bottom of two cabinets.
Door handle installation
Assembly steps
a. Use cross screwdriver to fix screws ② into the screw hole ① tightly.
b. Assemble the screw hole caps ③ on the screw holes of the handle.
c. The reverse operation is for disassembly.
Screw hole
Screw cover
Screw
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Refrigerador de point
point
point FS70W21 Manual de usuario
point
point KI3795E Manual de usuario
point
point RF32NW20N Manual de usuario
point
point RF32NW23E Manual de usuario
point
point PR855EW1 Manual de usuario
point
point RF33NW23E Manual de usuario
point
point FI3791E Manual de usuario
point
point RFI376E Manual de usuario
point
point RS900BSN Manual de usuario
point
point RS350BS23 Manual de usuario
