PMI BRAVO Manual de usuario
PMI®
BRAVO
HARNESS
SG51301
Manufacturer’s Instructions
PERSONAL GEAR HARNESSES
PMIROPE.COM 1-800-282-ROPE
T
PRODUCT DESCRIPTION
FEATURES
The Bravo offers specic features for tactical operation, theatrical use, or
any rigging and rescue applications at height as seen in Diagram A.
The Bravo is a lightweight, comfortable harness that provides a clean, low
prole for tactical operations, theatrical use, or any rigging and rescue
applications at height. Gear loops for this harness can be added and are
intentionally not pre-sewn for tactical and theatrical uses where gear loops
may interfere with desired performance and function. It is black to remain
unseen with tactical/theatrical clothing, has a Quick Clip Bent Bar D front
attachment point, secure Double Back Buckles on the leg loops, a Quick
Adjust Sliding Bar Buckle at the waist belt and it comes with a custom kit
that can add multiple gear loops for carrying additional equipment.
DIAGRAM A
.
Quick Adjust Sliding Bar
Buckle on adjustable
waist belt.
Secure Double Back
Buckles on adjustable leg
loops.
Elastic rear straps keep
leg loops positioned
correctly.
Lightweight.
Comfortable padding.
Black in color and low
prole so as not to be
easily seen.
Custom gear loop kit.
Sewn vertical webbing
attachment points for
custom gear loops.
DIAGRAM B
V1-0420
CERTIFICATIONS
SPECIFICATIONS
EN358:99; EN813:08
WARNING!
ABOUT YOUR PERSONAL SAFETY
• You are responsible for your own safety and decisions while using this
product.
• Before using this product you must thoroughly read and understand all
Manufacturer’s Instructions.
• Activities involving the use of this product are inherently dangerous;
you must understand and accept the risks involved.
• Special training and knowledge are required for the use of this product.
• Failure to follow these stated warnings may result in serious injury or death.
• Keep these Manufacturer’s Instructions, all product labels and the
Equipment Inspection Log WITH the equipment so that any potential
user can read them prior to use and make entries after use.
• Please contact PMI at 706-764-1437 to answer any additional
questions regarding safety and use of this equipment.
WARNING!
This harness is intended for use in tactical operations, theatrical rigging,
rescue applications and related activities at height. It should be used
with compatible life safety equipment and by a person with sufcient
knowledge of its proper use. The information in these instructions is
not a substitute for the training and experience necessary to use the
harness safely.
WARNING!
The Bravo Harness is tted with two different types of buckles for the
waist belt and the leg loops. The waist belt has a Quick Adjust Sliding
Bar Buckle to allow easy adjustment when properly rigged. The leg loops
have Double Back Buckles that function differently than the Quick Adjust
Sliding Bar Buckle. If not used properly, the buckles will not hold and
can result in serious injury or death. Inspect the buckles on receipt of the
harness and on the ground before using at height to ensure that they are
functioning properly. See Diagram C and D for proper use and threading for
both types of buckles.
MATERIALS: Nylon webbing, nylon stitching, steel buckles.
SIZE: WAIST 81-137 CM (32”-54”) LEGS 56-79 CM (22”-31”)
COLOR: Black WEIGHT: 1.1 KG ( 2.43 LBS) SKU# SG51301
WARNINGS
V1-0420
WARNING!
Harness should not be used near moving machinery, electrical hazards,
sharp edges, or abrasive surfaces without proper additional safety
measures in place. All webbing tails should be properly secured before use.
WARNING!
Any accessory gear loop that is added to the harness is designed
to attach equipment only and should NEVER be used for life safety
applications such as belaying, anchoring a person, or tying into a life
safety system.
WARNING!
The user should have a rescue plan prepared and the means available to
implement it while wearing this harness.
WARNINGS (continued)
DIAGRAM C
DIAGRAM D A properly fastened
Double Back Buckle.
A Properly Threaded Quick Adjust Sliding Bar Buckle
on the waist belt.
Pull tail end of webbing to
tighten waist belt.
Tilt buckle forward to
loosen waist belt.
This harness is designed to have a low prole and remain unseen in desired
situations. Often in tactical operations and theatrical rigging, there is less
need for gear loops. We give you the option to attach your own gear
loop(s) if you choose by providing a custom gear loop kit with this harness.
To secure gear loop(s) properly, see the section of these instructions
titled, “Bravo Gear Loop Attachment Instructions”. The Bravo Harness is
also designed to have a waist belt buckle that adjusts easily and quickly.
The design of the leg loop buckles allows them to stay secured by using
buckles that are fastened correctly when doubled back. Make sure you
understand the section, “How to put the harness on correctly” in order
know the differences in the buckles and how they function.
HOW TO PUT THE HARNESS ON CORRECTLY
• To ensure a proper t of the Bravo Harness, please follow the tting
steps in consecutive order in the section below.
DIAGRAM E
FITTING & USE
• Loosen the waist belt by
tilting the Quick Adjust Cam
Buckle and sliding the slack tail
end of the webbing towards the
buckle. Do not unthread the
webbing from the buckle.
Delta Double Back Buckle:
• Loosen leg loops by
sliding the slack tail end of the
webbing towards the buckle so
that you create a bight of
webbing that is positioned in the
middle of the buckle. Pull the
slack bight of webbing out of the
buckle opposite of the tail end of
the webbing to adjust the
harness to its largest size. Do not
pull the webbing completely
through the buckle.
•
Bravo Quick Adjust Sliding Bar
Buckle:
• Loosen the waist belt by
tilting the Quick Adjust
Sliding Bar Buckle and sliding
the slack tail end of the
webbing towards the buckle.
Do not unthread the webbing
from the buckle.
Bravo Double Back Buckle:
• Loosen leg loops by sliding
the slack tail end of the
webbing towards the buckle
so that you create a bight of
webbing that is positioned in
the middle of the buckle. Pull
the slack bight of webbing
out of the buckle opposite of
the tail end of the webbing
to adjust the harness to its
largest size. Do not pull the
webbing completely through
the buckle.
V1-0420
FITTING & USE (continued)
• Step through the top of the waist
belt, inserting a leg into each leg
loop with the buckles facing out in
front of your body. The elastic rear
strap should be oriented at the top
of the leg loops and there should be
no twists in the straps. The harness
webbing should not be twisted and
both buckles should look the same
on each leg.
DIAGRAM F
DIAGRAM G
• Position the harness so that the waist belt wraps over the top of the
hip bones and so that the Quick Clip Bent Bar D front attachment point.
is at about belly button level. Secure by slightly tilting the buckle and
by pulling back on the tail end of the waist belt webbing, as shown in
Diagram G.
FITTING & USE (continued)
• Secure the leg loops comfortably
around the thigh by pushing the leg
loop webbing to create a bight of
webbing in the center of the buckle.
Pull the side of the bight of webbing
farthest from the tail end of the
webbing out so that the slack is taken
out of the leg loop and is snug around
the thigh.
• Pinch the buckle and webbing to hold
in place, then with the other hand pull
the tail end of the webbing until the
bight and all slack gets taken out of
the webbing and the leg loop stays
rmly in place.
• When each buckle is tightened to the
desired snug t, take the tail end of
the webbing, tilt the buckle slightly
and slide the webbing though the
far side of the slot in the buckle and
pull tight to double back the buckle.
Once the webbing is doubled back
through the buckle, there should be
no less than 3 inches of the tail end
of webbing left. If there is less, then
readjust until you get 3 inches of
webbing or choose a larger size Bravo
Harness. A Double Back Buckle that is
fastened correctly so that it is secure
and will not slip is pictured in Diagram
D.
• Ensure that the leg loops and waist
belt are comfortable but snug enough
so that the harness stays rmly in the
proper position. You SHOULD NOT be
able to slide the harness down over
the hips once fastened correctly.
• Finally, adjust the rear straps so that
the slack is taken out.
DIAGRAM H
DIAGRAM I
V1-0420
Your harness should be thoroughly inspected before each use. Any
harness that does not pass inspection should be retired from service,
destroyed and discarded.
Inspections should include:
• Examination of all load-bearing components for signs of damage.
• Inspection of all stitching for signs of wear, fraying, breaks, loosened/
pulled threads, or cuts.
• Inspection of webbing for signs of cuts, burns, discoloration, broken
bers, hard/soft sections, or excessive wear.
• Examination of buckles and attachment points for proper function.
• Examination of all metal components for corrosion, damage or sharp
edges.
• Inspection of webbing rigging and buckles to ensure that harness has
been properly assembled.
• Inspection for any signs of damage from heat, chemical exposure, or
other environments.
• Inspection of date of manufacture and date placed in service to
determine if retirement of harness is needed (See “Retirement Criteria”
section).
• Inspections should be recorded and maintained in an Equipment
Inspection Log. A sample is provided in these instructions.
CARE AND MAINTENANCE
Maintaining your harness properly will provide a longer service life and
ensure the highest level of safety during use.
The following maintenance guidelines should be followed:
• Store harness loosely packed in a clean, dry environment.
• Thoroughly air dry a wet harness before storing it; never dry in a heated
dryer.
• Keep your harness away from exposure to direct ame or high
temperatures such as in a hot car.
• Prevent exposure of your harness to chemicals or other damaging
substances.
• No repairs or modications to this harness should be performed by
anyone other than the manufacturer, excluding the addition of the
gear loop kit, or warranty shall be voided and safety features could be
compromised.
Cleaning your PMI®Bravo Harness
Washing - If your harness is dirty, you can wash it by hand or in a front-
loading commercial washing machine. Use a PMI® Laundry bag for
keeping the harness from getting tangled/damaged when washing in a
machine. Wash harness by using cool to warm water <30°C (<86°F)
with a mild soap. PMI recommends using PMI® Rope Soap; otherwise
non-detergent soaps are best. Soap used should not contain any
bleaching agents.
Inspection, Care and Maintenance continued on next page...
INSPECTION, CARE & MAINTENANCE
DO NOT:
• DO NOT use top loading washing machines with agitators because
they tangle/damage the harness severely and can cause damage to the
machine.
• DO NOT use a commercial dryer to dry the harness.
• DO NOT leave a wet harness on a surface where contaminants may
leach (such as concrete).
• DO NOT expose the harness to exhaust fumes.
Disinfecting - Disinfection of a harness may occasionally become
necessary, such as when exposed to bloodborne pathogens. To disinfect
a harness from suspected bloodborne pathogens, PMI recommends
following the NFPA standard for cleaning rescue gear of bloodborne
pathogens. Keeping in mind that undiluted household bleach is known to
damage nylon, NFPA calls for using a diluted solution of household bleach
to clean rescue gear. Add 60 ml of household bleach per 4 liters of tap
water. That’s about one quarter (1/4) cup of bleach per gallon of water.
Be aware that some commercial bleach solutions are stronger than the
recommended 1.5% that is typical for household bleach. Soak the gear in
the diluted solution for ten minutes, then rinse thoroughly with tap water.
The rinsing cycle is critical to prevent any damage to the nylon from the
bleach. It is good to soak the gear in tap water for the same amount of
time it soaked in the bleach solution. Never store gear while it is wet.
WARNING!
The use of bleach over a long period of time, in repeated uses, can cause
damage to bers such as nylon. Disinfection of the harness using bleach
should be used sparingly and only when needed.
Drying - Dry your harness in a clean, dry area out of direct sunlight.
For best results, it should be hung up to air dry in a low-humidity
environment. DO NOT leave a wet harness on a surface where
contaminants may leach (such as concrete).
Write It Down - Remember to record the cleaning on the Equipment Log.
Keep It Clean - Store your harness in a clean, dark, dry environment, away
from exposure to acids, other harmful chemicals, noxious fumes or other
abuse.
RETIREMENT CRITIERIA
• RETIRE IMMEDIATELY any harness where the stitching is cut, torn,
excessively worn or visibly damaged.
• RETIRE IMMEDIATELY if harness has been in service for 5 years or
more, it must be retired even if a visual inspection reveals no concerns.
• RETIRE IMMEDIATELY any harness whose strength may have been
compromised during use.
• RETIRE IMMEDIATELY any harness which is subjected to a major fall or
uncontrolled or excessive loading.
• RETIRE IMMEDIATELY any harness with a manufacture date which is
greater than 10 years old, regardless of history and usage.
• RETIRE IMMEDIATELY any harness whose history and past usage you
INSPECTION, CARE & MAINTENANCE (continued)
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de seguridad de PMI
PMI
PMI SG51112 Manual de usuario
PMI
PMI SG51029 Manual de usuario
PMI
PMI SG51038 Manual de usuario
PMI
PMI HD26232 Manual de usuario
PMI
PMI SG51123 Manual de usuario
PMI
PMI FAST Manual de usuario
PMI
PMI AVATAR HARNESS Manual de usuario
PMI
PMI ACCESS PRO Manual de usuario
PMI
PMI Avatar Deluxe Manual de usuario
PMI
PMI CS TECH Manual de usuario
Manuales populares de Equipo de seguridad de otras marcas
Innova
Innova Xtirpa Manual de instrucciones
bolle SAFETY
bolle SAFETY B810 Manual de usuario
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manual de usuario
Hiltron security
Hiltron security POWER8E Guía
Hatco
Hatco B-950P Manual de usuario
Sitec
Sitec TX MATIC Manual de usuario
