Plus BF-030 S Operation Manual de usuario
PLUS
BF-030S
OPERATION MANUAL
First of all, we would like to thank you very much
for purchasing a Plus Board Fax CONFERENCE
MODEL.
Please read this Operation Manual before using
the machine to get the best performance out of
the product.
We recommend that you keep this manual for
future reference.
FEATURES ......................................................... 1
PRODUCT FEATURES ...................................... 2
CONTROL FUNCTIONS..................................... 3
HOW TO USE ..................................................... 4
MAINTENANCE/HOW TO STORE..................... 7
HANDLING PRECAUTIONS............................... 7
CHECK LIST OF SIMPLE FAILURES ................ 8
SPECIFICATIONS .............................................. 9
CONTENTS
EXPLANATION OF UL REGULATORY LABEL
(USA ONLY)
PLEASE NOTE: The description "Computer Rooms" on the
label located on the rear of the copyboard, refers to areas where
an abundance of computer control equipment (such as high output
servers) is being used, It does NOT refer to environments such
as offices or classrooms where there are simply PC's being used.
UL regulations require that we place a warning label in regard to
this item being used in a "Computer Room". Please understand
that this equipment will in no way interfere with the running of
computer equipment or peripherals. The UL regulation simply
applies to all items that contain flammable material in excess of a
specified area, We would like to further stress that there is no
inherent risk of this equipment causing a fire. It is only pointing
out that should a fire occur, then this equipment will also burn
along with any other flammable materials contained in the room.
Should you have any questions whatsoever about this information,
please call PLUS Corporation of America directly at (201)818-
2700
1
BF-030S BOARD FAX CARTON CONTENTS
Please be sure all of the following items are included in
the carton with the BF-030S BOARD FAX
Board Fax main unit........... 1
ACCESSORIES
Set of Dry-eraseble markers (one each black, red
and blue).
Dry-Eraser (1)
Fax Paper (30m(96ft) , 12mm(w/1/2") core)
Operation Manual with warranty card
OPTIONAL ACCESSORIES
PC interface board - to enable integration of the
BF-030S and your Personal Computer
The board size is W1200mm H920mm-large enough to show
all the ideas that you discuss during your meetings, without any
omissions.
Information on the large screen can be copied immediately onto
a sheet of A4/Letter paper.
Those who attend a meeting can concentrate on the subject,
as there is no need to waste time jotting down notes.
The board screen can be slid easily, and it is a simple user-
friendly unit with a power cord storage hook that comes in handy
when moving the unit, a powder tray enabling easy disposal of
powder, etc.
The BF-030S can be easily upgraded for use with your PC
(with optional PC interface board)
FEATURES
2
REAR
FRONT
Tray
PRODUCT FEATURES
Printer
Caster
T-shaped stand
Expansion slot
(for optional upgrades)
Optional accessory sold separately:
PC interface board - to enable down-
loading of board information from the
BF-030S to the PC
()
Board screen 50mm 50mm
gridded surface area
Operation panel
Printer cover
T-shaped stand
3
Opening button ............................. Press this button to open the printer hatch when replacing
the thermal paper.
Power switch ................................. Press "I" to turn ON the power when starting machine
operation.
Power lamp .................................... Press the switch, and the green lamp will blink on and off.
The lamp will stay lit (green) when the read sensor inside
the machine is ready for operation.
Paper warning lamp ....................... When the thermal paper has run out, the red lamp will
light. Load new recording paper.
One-surface copy key.................... This is used when one page of the screen is copied onto
A4 paper. The machine produces a copy at a reduced
scale of the same length and breadth.
Two-surface reduction copy key ..This is used when copying two pages of the screen at a
reduced size onto A4 paper. At this time, the copy is
reduced horizontally.
Repeat key ...................................... For use with optional PC interface kit.
PC COPY key ..................................For use with optional PC interface kit.
Feed/stop key ................................. This is used when the screen slides to the left.
Pressing this key advances the screen by one page and
then automatically stops.
Pressing the key while the board screen is being moved
stops it immediately. This can also be used when paper
has run out and must be refilled.
If this key is pressed during the copying operation, the
copying performance ends and the printer stops.
OPERATION PANEL
CONTROL FUNCTIONS
4
BEFORE USE...
HOW TO USE
WHEN COPYING...
Cut-off Recording Paper
When copying is completed, pull the tip of the recording
paper upwards and cut it off with the edge of the outlet.
When copying reduced two-surfaces:
Press two-surface reduction copy key. At this time the board
screen slides forward two pages, and the written contents are
reduced to A4 size and copied.
When copying one surface:
Press the one-surface copy key. At this time the board screen
slides forward one page and the written contents are copied
onto A4 paper.
POWER
POWER ON
PAPER OUT
Press the caster lock switches ON and keep
the casters in a locked position.
Plug in and turn ON the power switch. After
the power lamp blinks for 2-3 seconds, it
should turn green.
Press the feed/stop key to half the copying operation
immediately. The printer stops after completion of copying
up to that point.
5
HOW TO USE
WHEN SLIDING THE SCREEN FORWARD...
Manual sliding
It is also possible to slide the board screen manually. In
this case, it can be slid in either direction; to the right and
left. However, manual sliding at an excessively high speed
must be avoided as it occasionally causes problems.
Sliding by using key
Press the feed/stop key. Then, the board screen slides to
the left by one page and stops. It stops immediately when
the feed/stop key is pressed during the sliding operation.
Press the opening button to open
the printer cover.
Take out the core left over from the thermal paper.
WHEN REPLACING RECORDING PAPER...
*Concerning replacement of recording
paper
Replace with new recording paper in the following cases:
When a red line appears at the end of the recording paper.(A
red line appears when only about one meter or so of
recording paper is remaining.)
When the paper warning lamp lights red.
As illustrated, set it in so that the
tip of the new roll of recording
paper extends about 20cm from
the outlet.
6
When a red line appears at the edges of the recording paper. The red line will
appear when there is only about one meter (3 feet) or so of recording paper left on
the roll.
When the paper out lamp lights red.
HOW TO USE
Note:
Please use only the correct type of recording paper.
Particular attention must be given to the winding direction of the recording paper, since
copying cannot be performed if the winding direction of the recording paper is reversed.
Be sure to keep the recording paper straight when loading, failure to do so may cause
wrinkling or tearing of the paper during the copy function.
Push both ends of the hatch
closed until it locks with a clicking
noise. At this time, make sure that
the recording paper has not
slipped.
Replace the recording paper in the following situations
Cut off extra recording paper from
the printer outlet.
*Automatic Power Cut-off Function
If there is no key operation for about an hour, a fluorescent lamp inside the main unit automatically
goes off and the machine enters a state of power conservation. (At this time, the power lamp is lit.)
If at any time any key is pressed, the fluorescent lamp light again, and the normal operating
condition is restored.
7
<FOR SAFE USE>
1. Avoid placing the machine in hot spots where it is exposed to direct sunlight or
where an air conditioning duct.
2. When using sticky tape on the surface of the board screen, do not leave it on for a
long time. Moreover, after removing it, wipe the screen clean. Do not hit or pierce
the board screen with any hard or sharp objects.
3. Do not leave writing or marks on the board screen for a long time since it sometimes
become difficult to erase.
4. Be careful not to stain the joints of the board screen as there have been very rare
cases where such stains have been copied.
5. As thinner, benzine, alcohol, etc., may discolor or mark the main unit and the
board screen, never use such chemicals when cleaning.
6. Use only the correct type of recording paper.
When storing thermal recording paper, avoid the following places. This is important
because storage in such places may cause color development or discoloration.
(1) Places where the paper is exposed to direct sunlight.
(2) Places where the paper is exposed to temperatures of more than 35˚C and
humidity of 85% or over.
(3) Places adjacent to alcohol, thinner, benzine, ammonia, etc.
MAINTENANCE/HOW TO STORE
HANDLING PRECAUTIONS
Carry out the following maintenance procedures periodically to ensure high quality
copying performance at all times.
(1) Cleaning of the surface
When the surface gets stained, wipe it off with a slightly damp cloth. Also, if the stain
is particularly stubborn, use a solution of water-thinned neutral detergent to wipe it
off. Do not start using the machine until the sheet has completely dried.
(2) Cleaning of tray and decorative frame
Wipe away any dirt or residue left by the markers in the tray and the decorative
frame with a slightly damp cloth.
8
CHECK LIST OF SIMPLE FAILURES
HANDLING PRECAUTIONS
7. When replacing recording paper, do not place any objects on the open printer
cover or do not put your elbows on it.
8. After use, make sure to turn OFF the power switch. In addition, when it is not to be
used for a long time, make certain that the plug of the power cord is pulled out form
the outlet.
9. Always use the correct type of marker. Be careful not to use other markers as the
sheet may be damaged or, in some cases, the ink may be difficult to remove.
10. Write within an area of a size that can be easily read.
<BEFORE ASKING FOR A REPAIR SERVICE>
CONDITIONS CHECKPOINTS
If no satisfactory result can be achieved even after the above, contact the suppliers or our
company.
11. When moving this machine, turn OFF the caster lock switches, hold both the right
and the left sides of the main unit firmly, and avoid any sudden jolts or shocks.
When the power fails
When pressing copy key does not result
in copying
Although printer is functioning, nothing is
copied on recording paper
When characters written on board screen
cannot be rubbed out even by the use of
an eraser
When copy is dirty
Check if power cord is pulled out of outlet.
Check if paper warning lamp (red) is lit.
Check if winding direction of recording
paper is set on reverse. (No copying is
made on back of recording paper)
Check if any marker except the correct type
has been used. Wipe off with a damp cloth
or neutral detergent.
Check for ink residue on the screen. If it is
stained, wipe off carefully with a soft damp
cloth.
30mm 30mm
20mm
20mm
Otros manuales para BF-030 S Operation
2
Tabla de contenidos
Otros manuales de Proyector de Plus
Plus
Plus PLUS U7-132HSF Manual de usuario
Plus
Plus U2-X2000 Manual de usuario
Plus
Plus U5-512 Manual de usuario
Plus
Plus UP-1100 Manual de usuario
Plus
Plus DLPTM Technology Projector Manual de usuario
Plus
Plus U5-432 Manual de usuario
Plus
Plus U5-111 Manual de usuario
Plus
Plus U5-111 Manual de usuario
Plus
Plus V-339 Manual de usuario
Plus
Plus U4-112 Manual de usuario
Plus
Plus U4-232 Manual de usuario
Plus
Plus KJ-200 Manual de usuario
Plus
Plus U7-132 Manual de usuario
Plus
Plus PLUS Piano HE-3200 Manual de usuario
Plus
Plus U3 Manual de usuario
Plus
Plus U4-232 Manual de usuario
Plus
Plus V-1080 Manual de usuario
Plus
Plus U5-732 Manual de usuario
Plus
Plus U7-137 Manual de usuario
Plus
Plus U2-1150 Manual de usuario
