Plas-Ties TTP TWIST-TIE Manual de usuario
TTP MSDS FOR INKJET CARTRIDGES
4052 BLACK (RED GREEN BLUE) - FOR POROUS SURFACES
This ink is made expressly for use with Inkjet printers manufactured by PLAS-TIES, CO.. For best
results, please follow the instructions contained in the manual provided with the printer.
HEALTH 1
FLAMMABILITY 1
REACTIVITY 0
PERSONAL PROTECTION B
Reorder Part No. 4052BK or 4052RD or 4052GR or 4052BL
Distributed by:
PLAS-TIES, CO.
14272 CHAMBERS RD
TUSTIN, CA 92780
RISK PHRASE(S)
Large doses irratating to eyes and respiratory system. Ingestion may cause acute gastro-intestinal upset.
PRECAUTIONARY MEASURES
Wear safety glasses. Use solvent-resistant gloves and vapor respirator for spills, leaks or other high
exposures.
FIRST AID MEASURES
INHALATION: REMOVE TO FRESH AIR.
EYE CONTACT: CONTACT WITH THE EYES MAY CAUSE MILD IRRITATION. IMMEDIATELY
FLUSH WITH LARGE AMOUNTS OF CLEAN, LUKEWARM WATER (LOW
PRESSURE) FOR AT LEAST 15 MINUTES. SEEK MEDICAL ATTENTION IF EYE
IRRITATION PERSISTS.
SKIN CONTACT: WASH AFFECTED AREAS THOROUGHLY WITH SOAP AND WATER.
CLOTHING SHOULD BE LAUNDERED BEFORE REUSE. SEEK MEDICAL
ATTENTION IF SKIN IRRITATION PERSISTS.
INGESTION: INGESTION OF INK MAY CAUSE STOMACH UPSET. SEEK MEDICAL
ADVICE. SEEK MEDICAL ATTENTION IF STOMACH UPSET PERSISTS (THIS
INK CONTAINS ETHYLENE GLYCOL).
Guarantee Exclusion and Limitation of Liability: For a period of one year from the date of manufacture,
PLAS-TIES, CO.
(“Seller”) warrants that the ink shipped shall conform to Seller’s specifications.
EXCEPT FOR THIS WARRANTY, SELLER MAKES NO WARRANTY OF ANY KIND, INCLUDING
THE WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. On any
claim accepted by the Seller, SELLER’S LIABILITY SHALL NOT EXCEED ITS OBLIGATION TO
REPLACE THE ALLEGEDLY DEFECTIVE INK, OR TO RETURN THE PURCHASE PRICE PAID
BY THE PURCHASER FOR ALLEGEDLY DEFECTIVE INK. IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL OR SPECIFIC DAMAGES,
WHETHER IN TORT OR CONTRACT OR ANY THEORY OF LAW.
i
TTP PRINTING SYSTEM MANUAL
TWIST-TIE PRINTER (TTP) CONTROLLER
PRINT HEAD
CABLE PLUGS
IN HERE
ACCESSORY PLUG FOR
PRODUCT DETECT AND
ENCODER INPUT
TTP
CONTROLLER
KEYBOARD
POWER
SWITCH
WSYWIG LCD
GRAPHICS
DIAPLAY
INPUT POWER
110 VAC 60HZ
REFER TO USER
MANUAL FOR 220VAC
SETTINGS
SYSTEM
INK JET
TWISTTIE
STOPPED
- - - - > SPEED- 60
E F DELAY- 40
TWIST TIE PRINTER
ii TTP Printing System Manual
TTP TWIST-TIE INK JET PRINTING SYSTEM
INSTALLATION AND OPERATION MANUAL
TABLE OF CONTENTS
PART 1 Installation Procedures 1-1
PART 2 Operation Procedures 2-1
PART 3 Maintenance Procedures 3-1
PART 4 Troubleshooting and Repairs 4-1
PART 5 Parts List 5-1
iii TTP Printing System Manual
AMENDMENT RECORD
Amendment Date
All Pages at First Issue 19 SEPT 2003
iv TTP Printing System Manual
PART 1: INSTALLATION PROCEDURES
CONTENTS
INSTALLING THE TTP PRINTING SYSTEM 1–2
PLAS-TIES Model HD38, HD58, HD78 1–3
THREADING THE TTP PRINT CARRIAGE 1–11
INPUT POWER CONNECTION AND MODIFICATION 1–12
INSTALLING THE PRINT CARTRIDGE 1–13
CONNECTING THE TTP CONTROLLER TO THE CARRIAGE 1–14
CONFIGURING THE TTP PRINTING SYSTEM 1–15
TTP QUICK START 1–16
Creating a Message 1–17
Saving and Loading a Message 1–18
Special Fields in a Message 1–19
TTP SYSTEM QUICK SETUP 1–20
1 TTP Printing System Manual
INSTALLING THE TTP PRINTING SYSTEM
Determine the correct manufacturer and model number for your current equipment.
Manufacturers model numbers are affixed to a label located at the rear of the machines. If
you have any questions as to the correct make and model of your equipment, contact your
local equipment supplier.
Caution should be taken while installing the TTP printing system on your equipment.
PLAS-TIES, CO. has taken every precaution to ensure a safe and accurate instruction
set to guide the installer through the installation process.
Follow the operational guidelines in the correct installation procedures.
The TTP Printing System is shipped from the factory configured specifically for the
twist tie machinery requested. If it is necessary to re-configure the TTP Printing
System for a different twist tie machine follow the procedure on SYSTEM RESET
TO FACTORY DEFAULT SETTINGS.
VERIFY THAT YOUR EQUIPMENT IS IN PROPER
OPERATING CONDITION
LOCATE THE CORRECT MAKE AND MODEL OF YOUR
EQUIPMENT
FIND THE PROPER INSTALLATION INSTRUCTIONS FROM
THE FOLLOWING INSTALLATION PROCEDURES
READ CAREFULLY ALL INSTALLATION PROCEDURES
BEFORE PROCEEDING
INSTALL THE TTP PRINTING SYSTEM ON YOUR
EQUIPMENT. THERE IS NO EXTRA HARDWARE
REQUIRED OTHER THEN THAT SUPPLIED IN THE
INSTALLATION KIT. THERE ARE NO EXTRA HOLES TO
BE DRILLED. DO NOT DISCARD ANY SCREWS REMOVED
IN THE INSTALLATION PROCESS; THEY WILL BE USED
FOR THE INSTALLATION.
2 TTP Printing System Manual
INSTALLATION FOR PLAS-TIES MODEL6+'+'+'
To install the printer, first remove and retain the two screws and washers that hold the
Brake Arm Assembly in place. Using the two screws supplied in the installation kit,
attach the Extension Arm Assembly (C20821) to the two holes in the Brake Arm
Assembly. Attach the Brake Arm Assembly to the twist tie machine base using the two
existing hardware.
TTP-+' MOUNTING ASSEMBLY
Re-install the existing
arm assembly with the 2
existing mounting
screws
Remove the 2
mounting screws
that hold the
existing bracket and
attach the extension
bar assembly
C20821 with the
two 10-32 screws
supplied with the
mounting kit
3 TTP Printing System Manual
Install the print head as shown in the diagram below. Note the orientation and tighten the
two knurled knobs to fasten the print head to the extension bar.
TTP-+' ASSEMBLY
Mount the print
head mounting
bar C20821with
the two 10-32
screws supplied
with the
installation kit
Mount the print head
assembly C20812 to the
mounting assembly C20837
and justify the head assembly
to the extreme back of the
b
racket as shown and tighten
the two knurl knobs
4 TTP Printing System Manual
THREADING THE TTP PRINT CARRIAGE
The TTP print carriage is threaded the same for all TTP models. During the threading
process make sure that the twist tie material has the paper side facing toward the ink
cartridge. The inks used are intended for a porous material and WILL NOT ADHERE
TO THE PLASTIC SIDE OF TWIST TIE MATERIAL.
To thread the TTP print carriage C20812 insert the end of the twist tie material between
the notch in the TAPE GUIDE (paper side faces as shown). Pull back on the PRESSURE
ARM in the direction depicted by the arrow and continue to completely pass the twist tie
material through the carriage assembly. Continue to pull the twist tie material and insert
into the twist tie machine per manufacturer recommendations.
TAPE GUIDE NOTCH
TAPE DIVERTER
PRESSURE ROLLERS
PRESSURE ARM
TAPE GUIDE
11 TTP Printing System Manual
Tabla de contenidos
Otros manuales de Impresora de Plas-Ties
