Planex Cloud Connect CS-W06N Manual de usuario
CS-W06N
Planex Cloud Connect
CS-W06N
2
Table of Contents
1. INTRODUCTION..........................................................................................................................4
2. HARDWARE DESCRIPTION AND QUICK INSTALLATION/USAGE ................................6
2.1. MAJOR HARDWARE COMPONENTS.......................................................................................6
2.2. QUICK INSTALLATION AND USAGE ........................................................................................8
2.3. WIRELESS CONNECTION (IF ROUTER/AP HAS WPS BUTTON)..........................................12
2.4. WIRELESS CONNECTION (IF WPS NOT SUPPORTED ON ROUTER/AP)..............................12
2.5. PUSH NOTIFICATION ............................................................................................................13
3. WEB CONFIGURATIONS........................................................................................................15
3.1. INFORMATION ......................................................................................................................16
3.2. VIDEO DISPLAY ...................................................................................................................17
3.3. NETWORK............................................................................................................................18
3.4. WIFI SECURITY....................................................................................................................19
ADVANCED NETWORK.......................................................................................................................21
3.5. VIDEO SETTINGS.................................................................................................................22
3.6. MOBILE VIDEO SETTINGS....................................................................................................24
3.7. NIGHT MODE CONTROL .......................................................................................................25
3.8. EMAIL/FTP ALARM ...............................................................................................................26
3.9. SPEAKER ALARM SETTINGS ...............................................................................................29
3.10. NAS SETTINGS....................................................................................................................30
3.11. SD-CARD SETTINGS ...........................................................................................................32
3.12. SCHEDULING .......................................................................................................................34
3.13. LED DISPLAY CONTROL......................................................................................................36
3.14. DATE/TIME...........................................................................................................................37
3.15. ADMIN..................................................................................................................................38
3.16. UPGRADE ............................................................................................................................39
3.17. REBOOT...............................................................................................................................40
3.18. SET TO FACTORY DEFAULT..................................................................................................41
4. FEATURES AND SPECIFICATIONS......................................................................................42
4.1. FEATURES ...........................................................................................................................42
4.2. SPECIFICATIONS..................................................................................................................43
APPENDIX A. MAXIMUM ALLOWED VIDEO USERS.................................................................45
APPENDIX B. PERFORMANCE INFORMATION .........................................................................46
APPENDIX C. TROUBLE SHOOTING............................................................................................48
CS-W06N
3
APPENDIX D. SNAPSHOT PICTURE ON ANY BROWSER.......................................................50
CS-W06N
4
1. Introduction
The IP Camera is designed for all day video surveillance on your
iPhone/iPad and Android mobiles/pads. The setup is truly 1-2-3 :
1. Connect the camera to the network
2. Download the app Touch2See into your iPhone/iPad or Android
3. View video by the camera ID/password
The push notification is supported, so that you will get the notification from
your iPhone/iPad and Android once there is any events detected through the
PIR body sensor or sound detector on the camera, even when your mobile is
on sleep mode.
The SD card recording is supported, and you could playback the recorded
video on your iPhone/iPad and Android. You could also do the SD card
recording only when there is PIR or sound detection to save the SD card
storage size. The PIR and sound detected recording has a 5 seconds
pre-recording, so that you will always catch the critical moment.
For day & night usage, there are two video sensors/lens on the camera,
one for day and one for night. The day lens and night lens focus are separately
tuned for day light and Infra Red light for best video quality. No ICR, no
mechanical problem.
Two-way audio is supported. You can monitor the synchronized
video/audio and talk to or warn the people around the camera from your
iPhone/iPad and Android once you got the push notification. The speaker jack
is supported so that you could connect any high power speaker to the camera
for your needs.
The WPS(WiFi Protected Setup) is supported. You could set up the WiFi
connection of the camera with the router by clicking the WPS button on the
camera and on the router at the same time. No more complicated WiFi
configuration.
The IP Camera is ideal for securing small businesses, home offices and
residences. The IP Camera is a perfect replacement of the alarm system and
CS-W06N
5
baby monitor in your house and shop. .
The differences
It’s very easy to see the video of the Day&Night IP Camera, you only need to key
in the ID/Password of the IP CAM any where in the world, you do not need to
remember the IP address or domain name or DDNS name or port number. And you
do not need to modify the settings(like port mapping, fixed IP, DDNS, virtual server) of
the NAT/router devices, it’s just a plug & play usage.
CS-W06N
6
2. Hardware description and quick installation/usage
The IP CAM is designed to be very easy to install and use. First, let’s see the
major components of the IP CAM products.
2.1. Major hardware components.
The major components on the front panel of the IP CAM products are the built-in
microphone, lens and LEDs :
1. Microphone – for receiving the audio/voice. Effective distance is about 5 meters.
2. Lens – the lens is inside the camera body and the focus of the lens is fixed, you do
not need to spend time to adjust the focus, the effective focus range is from 30cm
to infinity. There are two lens for day and night usage separately.
3. Status indication LED (red) – this LED is to indicate the Internet connection status.
When the Internet connection is connected, the LED will be constant red light. If
there is any Internet connection problem, the LED will be blinking red light.
4. Ethernet indication LED (blue) – this LED is to indicate if the Ethernet link is ok
and packet traffic is sending/receiving. When the Ethernet cable is connected, the
LED is on. When there is packet sending/receiving, the LED is blinking blue light.
5. SD card indication LED(yellow) – this LED is to indicate the status of the Micro-SD
card recording, it will be on when the Micro-SD card is inserted and will blink
during recording.
6. Micro-SD card slot – for inserting the Micro-SD Card. (support up to 32G bytes)
7. WPS button – this is to automatically synchronize the WiFi settings with a WPS
capable WiFi router.
8. Speaker jack – connect to an external speaker for two way audio and speaker
alarm usage.
9. PIR sensor – for the detection of the human body.
10. IR LED – for the Infra Red lighting of the night mode usage.
CS-W06N
7
Figure 2-1: Major components in the front and side panel
The major components on the back panel of the IP CAM products are the bracket
screw jack, power jack, Ethernet jack and reset button:
1. Bracket screw jack – this is the position to screw in the bracket of the IP CAM.
With the bracket, you can put the IP CAM on the desk, on the wall or on the
ceiling.
2. Power jack – this is the place to plug in the power adaptor. The power needed for
this IP CAM is 12V/1.0A, please make sure you are using the correct power
adaptor.
3. Ethernet jack – this is the place to plug in the RJ45 Ethernet cable. When the
Ethernet link is ok, the Ethernet indication LED on the front side will be blue light.
4. Reset button – this is the button to reset the IP CAM to default factory settings.
You need to use a small stick like pencil or tooth stick to press the reset button for
more than 3 seconds to enable the reset function. Usually when you forgot the
administrator account, you will probably need to do this reset action to reset to the
default factory settings. Please refer to section 3.19 for more details.
CS-W06N
8
Figure 2-2: Major components in the back and bottom panel
2.2. Quick installation and usage
There are only three things that you need to do to see the video from the IP CAM.
1. Connect the IP CAM to the home/office network.
2. Install the Touch2See software on the notebook/PC.
3. Key in the ID/password of the IP CAM(from the ID/Password card) on the
Touch2See, and then you can see the video.
First, Connect the IP CAM to the home/office network
Please connect the IP CAM accessories to the IP CAM body correctly, including
the power adapter and Ethernet cable. And connect the other end of the Ethernet
cable to the home network or office network. Usually, this Ethernet cable is plugged
into a home NAT/router device or an Ethernet switch if in the office, as shown in
Figure 2-4. Since the default settings of the IP CAM use DHCP function and very often
there is a DHCP server on most of the Home/office network, the IP CAM should be
connected to the Internet immediately. The Internet status LED is constant red light to
indicate this good connection status. If the LED is blinking, please refer to section
3.3~3.5 to try other network settings.
CS-W06N
9
Figure 2-4: Connect Ethernet cable to a switch/router.
Second, Install the Touch2See software on the notebook/PC
Please download Touch2See from Web site, and install it on your notebook or
personal computer (must be running Microsoft Windows OS).
Windows 7 : http://www.planex.com.tw/FileHandler.ashx?id=1248
Windows XP/Vista : http://www.planex.com.tw/FileHandler.ashx?id=1250
Execute the program Touch2SeeInstaller-xxx.exe on the disk. The program will
pop-up some windows about the installation options, please press the “next” button to
proceed with the installation. After the installation is complete, there will be a
Touch2See icon on the desktop of your computer screen, please execute this icon.
The Touch2See program will run immediately.
Third, Use Touch2See program to see the video
If the computer and IP CAM is connected to the same network, the IP CAM ID
will be displayed in the “Auto Search” list. You can double click the “Auto Search” to
search all the connected IP CAMs any time. The only thing left right now for seeing
the video is to double click the IP CAM ID item in the “Auto Search” list.A window
asking for password input will pop up. Please key-in the password in your
ID/Password card into this field and click “ok”. The video will then be displayed on the
window.
CS-W06N
10
Figure 2-6: The ID/Password card
Notice 1:
1. You can modify this play-video password by entering into the web configuration
pages. Please refer to section 3.6 for more information.
2. You can also add the IP CAM into the CameraList in the Touch2See software to
have more convenient video display, please refer to the user manual of the
Touch2See software for more functions.
Seeing the video in a remote location
After the IP CAM is installed and you can see the video from the Touch2See
software in the local network, it’s very easy to see the video in a remote location. All
you need to do is add a camera item in the “CameraList” folder of the Touch2See
software, key in the IP CAM ID and Password(from the ID/Password card). And then
double click this camera item. You will then see the Camera video immediately. No
further NAT/router setting modifications are needed.
Tabla de contenidos
Otros manuales de Cámara IP de Planex
